Products Properties : 1. high tensile strength, large ductility, strong applicability for contraction or deformation of the substrate. 2.large width of material, high construction efficiency, small product consumption 3.Good diffusivity of water vapor, easy discharge of condensate, easy discharge of moisture left in the substrate 4.Root penetration resistance, chemical corrosion resistance and aging resistance 5. good flexibility at low temperature even at -30â?? and heat resistance 6.No liquid flow at high temperature 7. Cold construction and good safety performance. Size & Specification Size: 2m (width)*20m (length) Thickness: 1.2mm; 1.5mm; 2.0mm Type: Homogeneous, Reinforced, Fabric back,also we can make self adhesive style Exposed and Non-exposed Color: white, Grey or customized Certificate: ISO9001/14001, Root Resistance Certificate Product Application Widely used for waterproof and anti-seepage, caverns, tunnels, subway, bridge, water conservancy dam basement, landfills, sewage treatment pool, municipal construction
polyethylene(PVC) geomembrane, as a high performance waterproof and impermeable material, has many remarkable advantages. Thickness: 0.1mm-3mm Width: 2m-6m Color: Black/White/Other colors Following is our PVC geomembrane Thickness 1.6mm spceifications: Tensile Strength (vertical and horizontal): 20MPa/mm Elongation at Break (vertical and horizontal): 580% Right-angle tearing strength (vertical and horizontal): 180N/mm Water vapor permeability coefficient: Using temperature range: +70â??~ -70â?? Puncture strengthâ?¥360N Water impervious: 100% Root resistance: 100% Difference Between PVC Geomembrane and HDPE Geomembrane PVC geomembrane and HDPE geomembrane have significant differences in physical properties, treatment difficulty, joint treatment, puncture resistance, and resilience to deformation. Physical Properties and Suitable Environment: PVC membrane: relatively soft and easy to bend, suitable for general waterproofing projects, swimming pools, and wastewater treatment, etc. HDPE membrane: has higher strength and wear resistance, suitable for engineering projects with higher strength and durability requirements, such as water conservancy projects and landfills. Handling Difficulty: PVC membrane: Due to its flexibility, we can make seams in controlled factory conditions, typically requiring fewer on-site seams than HDPE geomembrane. HDPE membrane: Handling in cold weather conditions can be challenging and requires sewing outdoors. Puncture Resistance: PVC membrane: It is harder to penetrate than HDPE and has high elongation characteristics, allowing it to adapt to site changes without reinforcement. HDPE membrane: While it has elasticity, it becomes plastic after exceeding its yield point and no longer has elasticity. Deformation Recovery: PVC membrane: Most of the deformation can be recovered, with a high tensile elongation, suitable for engineering projects with larger design strain limits. HDPE membrane: Deformation after exceeding the yield point cannot be recovered, and the material properties will change. We should select the appropriate geomembrane according to the specific project requirements and the use environment. HDPE geomembrane is suitable for projects that require high strength and durability, while PVC geomembrane is suitable for general waterproofing projects and water treatment.
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards. We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm) APPLICATIONS Road and Highway surfaces Constructions or Civil work Railway Ballast To make Concrete or Asphalt Filling
test app vikasgo4wb
Plastic scrap (ldpe, pp, pvc, pet, pmma, hdpe, bopp, pe, ps, abs etc)., textile waste (cotton hosiery clips, cotton thread waste), denim, unbleached, selvedges rama string, rags for mattresses, wiping rags, licekrin dropings 100% cotton bales, card fly etc.) paper scrap.
Shampoo, soap, toothpaste, shaving razor, hand body lotion, household cleaning products, coffee beans, instant coffee, coffee mix, tea, chocco, biscuits, wafer, cookies, milk, candy, canned food.Buying & sourcing agent
Aluminium ( ingots, t bars, sows, rods), copper (cathodes, cakes, billets, ingots, rods), lead (ingots), nickel (cathodes both cut and uncut briquettes, pellets, discs, etc.), tin (ingots, etc.), zinc (ingots both regular size and jumbos), steel billets (all types including crc, hrc, hdgc, plates, sheets), concentrates and ores for above items including bauxite, manganese, clinker and iron ores etc), scraps of above items including hms 1&2 and steel scraps.
It uses PVC resin as the main raw material with a variety of special additives and anti-aging agents. Advantage: 1. High compressive strength, high elongation and small size change in heat treatment. 2. Good low temperature flexibility. 3. The lap side can be welded with high strength. 4. Chemical resistance. 5. Good plasticity. Application: Waterproof and moisture proof works for roof and underground space of various buildings. Specification: 1. Thickness: 1.2/1.5/2.0mm 2. Width: 1000/2000mm 3. Length: 20m
PVC waterproofing membrane Production description: The pvc waterproofing(waterproofing membrane)rolls formulas are based upon polyvinyl chloride resin with other assistants added to provide flexibility and stability such as anti-oxidant, absorbent of ultraviolet light, plasticizer and plastic filling agent Features: 1. Exposed to sunshine: UV rays resistance, long service life and aging resistance 2. Easy installation and dimensional stability: can be wieldable under wide range of temperature and experience minus dimensional change in thermal treatment 3. High tensile strength and elongation thus can accommodate movements of substrates 4.Good flexibility under low temperature, good adaptability to ambient temperature difference 5, secure anti-puncture and good rooting resistance, no pollution caused to environment when being welded and good waterproofing choice for plant roofs 6. Good plasticity: convenient and fast treatment of detailed parts of corners and edges 7. 2 meters width reduce the joints and help saving materials or labor cost Type: 1. PVC membrane (h) 2.Pvc membrane with fiber composite backing sheet (l) 3. Reinforced pvc membrane within fabric (p) 4. Reinforced pvc membrane within glass fiber (g) 5. Reinforced pvc membrane within glass fiber and fiber composited backing sheet (gl) Application range : Pvc membranes form an effective barrier to liquid water or water vapor in the roof construction for industrial and civil engineering, underground engineering such as subway & tunnel, water conservancy such as water pools & ditch, shelter, grain depot, land filling, dyke, sewage treatment and basement. Thickness(mm); 1.2 1.5 2.0 Width(m); 2 Length(m); 20
Grocery items such biscuits, air freshener, instant coffee, snack, tea bag, instant noodles, toothbrush, toothpaste, personal care, food and beverage, female napkin, detergent powder, floor liquid cleaner, dishwashing liquid soap.
Hpm-p polyvinyl chloride (PVC) series waterproof rolling materials, is a new type of polymer waterproof rolling materials processed with polyvinyl chloride resin as raw material, plasticizer, antioxidant, filler, ultraviolet absorbent and other auxiliary agents. Product Feature * superior aging resistance * resistant to root penetration, especially suitable for planting roofing * welding construction, weld solid and reliable and environmental protection and pollution free * high tensile strength, good elongation, good dimensional stability * has good plasticity * with self-extinguishing function * colorfast and pollution-free Product advantage * flexible material, suitable for various architectural shapes * quick construction and short time limit * less affected by weather conditions, flexible construction
Roof Basement Waterproof Material Pvc Membrane Description: PVC membrane roll is an excellent high-quality polymer waterproof sheet, made of PVC resin by adding plasticizer, anti-UV agent, anti aging agent, and stabilizer and other processing aids through extrusion and molding. As the highly-recommended product by the Ministry of Construction, it is featured by high tensile strength, great elongation, good stability, small shrinkage, low-temperature performances, good resistance to weathering and root penetration, and long service life. Specifications: Product name PVC roof sheet waterproof membrane with UV protection Brand MINGDING Thickness 0.8mm, 1.0mm, 1.2mm, 1.5mm, 2.0mm Width 1.05m, 2.05m, 2.1m Length 20m or customized Type H type, L type, P type Property: Strong tensile strength, high elongation, good dimensional stability after heat treatment. 2)Excellent flexibility at low temperature, excellent resistance to the low and high temperature. 3)Excellent resistance to impact and perforation. 4)Excellent resistance to chemical etching. 5)Fireproof : the membrane extinguish immediately after away from the fire source. 6)Easy and fast construction without pollution. 7)Excellent resistance to the aging, long service life. Service life: more than 20 years as roof waterproof material, more than 50years if used in underground waterproof . 8)Repair project: Repair the damage place only and reduce the repair cost. 9)Various colors are available.
Company in Israel interested in selling pvc reinforced waterproofing membranes for roofing and swimming pools/uv resistant-in KG-several colors, widths, thickness and widths. Membranes have optical defects like spots, color. non standard lenghts Rolls are on pallets and selling is per KG
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years. APPLICATIONS Soil stabilization Mortar Used in combination with Portland cement Pre-cast concrete Ready mix concrete Specialist projects
Feldspar is the name given to a group of minerals distinguished by the presence of alumina and silica (SiO2) in their chemistry. This group includes aluminum silicates of soda, potassium, or lime. It is the single most abundant mineral group on Earth. They account for an estimated 60% of exposed rocks, as well as soils, clays, and other unconsolidated sediments, and are principal components in rock classification schemes. The minerals included in this group are the orthoclase, microcline and plagioclase feldspars. APPLICATIONS Glass making Ceramics Porcelain Electrodes Abrasion We at CEMENTATION produce Feldspar of minerals containing Potassium and Sodium. Our supply is available in Lumps, Granules and Powder form.
Quartz is the most abundant and most common mineral on the Earth. It is found in almost every geological environment and also it is at least a component of almost every rock type. It has a hexagonal crystal structure and is made of trigonal crystallized silica. It is most varied in terms of varieties, colours and forms. The most important distinction between the types of quartz is that one is of macro crystalline, which is individual crystal visible to the unaided eye, and the other is microcrystalline or cryptocrystalline varieties, aggregates of crystals visible only under high magnification. Chalcedony is the generic term for cryptocrystalline quartz. The transparent variety tends to be microcrystalline and the cryptocrystalline varieties are either translucent or mostly opaque.
Bauxite is a naturally occurring mineral comprising mainly of aluminium hydroxides (the trihydrate Gibbsite Al(OH)3and the AlOOH monohydrate polymorphs boehmite and diaspore), with other components in the mineral typically being silica, iron oxide, titania and aluminosilicates (clay etc). It’s a rock from Laterite soil and it is a primary Ore of Aluminium. Properties of Bauxite include low iron content; a high Polished Stone Value (PSV) for high friction surfacing applications; a high melting point and density. APPLICATIONS Gunning materials High friction surfacing Minerals for abrasion Refractory castables Mouldable and Ramming Mixes Refractory mineral blends CEMENTATION believes in supplying quality bauxite with consistency to its customers across the world, according to their needs.
The CORI is the product for the direct reduction unit: First, it will be stored in product passivation silos, its transportation by conveyors. After that, it will be stored in the warehouse for further use. Production rate fo312 T/H. Assuming 8,000 hours of annual operation, this equates to in annual production of 2,500,000 tonnes. -IRON: (Rod a Benton):Hot-rolled product in multipurpose steel for high-adherence construction, weldable in RB 500 grade. NA 8634(2015) and ISO 6935-2 (2015). Diameter: A wide range of diameters: 8,10,12, 14, 16,20,25,32,40 mm. Length :12m (-0mm +100mm) with the possibility of making specific lengths of less than 12m according to customer demand for diameters ranging from 8mm to 16mm. 12m to 18m for diameters ranging from 16mm to 40mm. Marking : A specific AQS marking is engraved on the rebar bars for the diameters: 8,10,12,14,16mm And the identifying code AQS-diameter-RB500 for the diameters: 16,20,25,32,40mm - Portland Cement 42.5 (Bags, Bulk) -Wire rod: of round section with a diameter varying between 5.5 mm to 14 mm, of high quality. The round and smooth wire rod is obtained by hot rolling in accordance with the Algerian standard an 8634 and according to international standards.-The Fields Of Use Of Wire Rod Are As Follows:- Drawn Wire-Welded Mesh-Nail, Tie Wire, Galvanized Wire- Gabions- Barbed Wire-Spring Wire- Bolt-Nut-Screw- Paperclips-Pickup Wire-Welding Wire -BILLET: A billet is a section of metal used to roll into bars and shapes. It can be produced with ingots or directly by continuous casting. Billets are used as raw materials or for extrusion, forging, rolling and other metal processing operations.
