Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Class: AAA High-class shell and foreign material (by weight) 0.05% maximum meal or dust (by weight) 1% maximum thru 3/32" color fairly uniform in color, notdarker than "amber" skin color color classication fancy mostly golden color or lighter, max 3% by weight darker than light total defects (by weight) 3% maximum, due to o-sizing moisture 2 % maximum size min / max diameter fancy x-large 8/16" not a complete half fancy large 7/16" 8/16" fancy medium 4/16" 7/16" fancy small 3/16" /4/16" fancy midget 1/16" 3/16 Nutrient ingredients: Protein, Carotene, Crude fiber, Calcium, Phosphorus, Iron and Vitamin C, B1, B2, E. Character: Easy open, Crisp kernel, pure natural processed, green & healthy, good taste. Functions: Prevent cell aging; Lower cholesterol; Improve memory, aging and moisturize the skin; Anti-cancer; Bacteriostatic antiphlogistic.
Class: AAA High-class shell and foreign material (by weight) 0.05% maximum meal or dust (by weight) 1% maximum thru 3/32" color fairly uniform in color, notdarker than "amber" skin color color classication fancy mostly golden color or lighter, max 3% by weight darker than light total defects (by weight) 3% maximum, due to o-sizing moisture 2 % maximum size min / max diameter fancy x-large 8/16" not a complete half fancy large 7/16" 8/16" fancy medium 4/16" 7/16" fancy small 3/16" /4/16" fancy midget 1/16" 3/16 Nutrient ingredients: Protein, Carotene, Crude fiber, Calcium, Phosphorus, Iron and Vitamin C, B1, B2, E. Character: Easy open, Crisp kernel, pure natural processed, green & healthy, good taste. Functions: Prevent cell aging; Lower cholesterol; Improve memory, aging and moisturize the skin; Anti-cancer; Bacteriostatic antiphlogistic.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube OD 20~405mm in theory Thickness 1.2~15.7mm Length Any Length Below 16 Meter Standard GB,ASTM,BS,EN,JIS Material Chinese Grade, Q195, Q215 Q235, Q345 ASTM, Grade B,Grade C,Grade D,Grade 50 EN, S185,S235JR,S235JO,E335,S355JR,S355J2 JIS, SS330,SS400,SPFC590 Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery Ends Plain, Beveled, Thread With Couplings Or Sockets; Plastic Caps And Steel Rings Can Be Provided If Possible Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment Technique Hot Rolled Or Cold Rolled ERW Package Covered With Tarpaulin, Containers Or In Bulk
Product name: 3-O-Ethyl-L-ascorbic acid Other Name: 3 O Ethyl Ascorbyl Ether INCI Name: 3-o-ETHYL ASCORBIC ACID Molecular Formula: C8H12O6 Molecular Weight: 204.18 Appearance: White crystalline powder Purity: 99% CAS NO.: 86404-04-8 EINECS No.: 617-849-3 Supplier: ZHENYIBIO 3-O-Ethyl ascorbic acid is a new generation of vitamin C derivatives with excellent whitening effects and strong anti-aging activity,which can promote collagen synthesis and protect skin from DNA damage.3 O ethyl ascorbate ether has a powerful inhibitory effect to inhibit melanogenesis,reduce dark spots and age spots,combat photoaging by interfering with inflammatory cytokines (such as IL-6),and reverse the generation of ROS to achieve the purpose of scavenging free radicals.3-O-Ethyl ascorbic acid is a new form of vitamin C with better overall performance.It is water-soluble and has excellent heat resistance and light stability.Most importantly,it is highly stable and easy to formulate.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE :- BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray THINNER :- Type 290 POT LIFE :- 3 hours min at 30�° C RECOMMENDED DFT :- 30-40 �µ. OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Type 290 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Type 290 Addition : Max 5% Nozzle Orifice : 0.28- 0.37 mm Nozzle Pressure : 1400-1800 p.s.i.
INTRODUCTION The product is a high molecular 30 TBN Calcium Sulphonate. The increased oil solubility of the organic portion of this Sulphonate enables the product to provide rust protection and acts as a dispersant for graphite and molybdenum disulfide. It can be used as an additive in lubricating oils, greases, rust inhibition, antiwear and hydraulic fluids. SPECIFICATION Test Method Minimum Maximum Appearance Visual Brown liquid Brown liquid Colour ASTM D 1500 2 5 Sp. Gravity @ 15.6 C ASTM D 1298 0.95 1.05 Flash Point C (COC) ASTM D 92 175 - Viscosity @ 100 C, cst ASTM D 445 40 70 Avg. Molecular wt. ASTM D 3712 1000 1100 TBN (mg KOH/gm) ASTM D 974 28 35 Calcium Content %[w/w] GL EDTA 1A 2.8 3.0 FORMULATION The product is recommended for use at 0.5% to10.0%wt. In suitable base stocks to provide detergency & anti-rust performance characteristics to oils. It is compatible with mineral base oils, white oils, and synthetic base stocks. APPLICATION Imparts excellent rust prevention, detergency and Anti oxidant Properties. Corrosion inhibitor in mill oils, short-term rust preventatives, coatings and greases. Dispersant and corrosion inhibitor in engine oil. Provides excellent resistance to coated Cold Rolled Steel for antirust applications. Works in extremely hostile conditions like highly acidic environment as well as highly humid atmosphere. It is non-staining having detergent, dispersant properties. Environmental Friendly, Biodegradable without side effect. HANDLING AND STORAGE Calcium Sulphonate is normally handled at room temperature. For general purposes, the following storage and handling temperatures are recommended: Storage Handling 50-70C (122-158F). For more extensive information on the safe handling and use of this product, see the Material Safety Data
We are sellers of certified halal frozen whole chicken, chicken feet, chicken , beef, pork our products meet the SGS testing, we can supply all kinds of frozen chicken cuts. Freezing Process: IQF Part: Whole Shape: Packaging: Cartons Shelf Life: 12 months We supply high quality and large quantities of Halal and non-halal frozen whole chicken, frozen chicken feet and frozen chicken parts. The different types of frozen whole chicken and frozen chicken parts that we supply are: A. Whole chicken. Please indicate the size that you want. B. Chicken leg quarter/Chicken whole leg C. Chicken drum stick D. Chicken thigh E. Chicken boneless leg F. Chicken G. Chicken wing tips H. Chicken 2 joint wing I. Chicken whole leg boneless with skin on J. Chicken feet K. Chicken gizzards L. Chicken wing middle joint M. Chicken inner fillet middle half cut N. Chicken boneless and skinless breast without inner fillet O. Chicken half breast boneless and skinless without inner fillet Q. Chicken head R. Chicken back S. Chicken front T. MDM Specifications: - Feather off - well cleaned and fresh - no bruises - no black pads or ammonia burns - no bad smells - no excessive blood or blood stains - moisture content is less than 3% weight and packaging: whole chicken each weight 800g to 2500g x 7-10 in a box Other parts from 2kg up to 10 - 15/20kg Payment Terms : TT Only
Product Data Sheet GENERAL DESCRIPTION An easy-to-use, water-based primer specifically formulated to �¢??lock-out�¢?? corrosion on a wide range of metals. Applied correctly, is guaranteed for years. USES Suitable on sheet metal, castings, wrought iron, TNT Bar, steel Bar and steelwork. This product is not recommended for automotive use. COLOURS Available in natural green. SIZES Available in 4 litre,10 litre and 20 litre COVERAGE Up to 14 square metres per litre depending upon surface porosity and application method. APPLICATION Roller, brush, dip or airless spray. Provide adequate ventilation during use. DRYING TIMES Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (30�?�°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary. DO NOT USE IN TEMPERATURES BELOW 10'c OR ABOVE 45C. DANGEROUS GOODS CLASSIFICATION Not classified as Dangerous Goods. SURFACE PREPERATION Previously Painted Surfaces : Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer. TNT BAR,STEEL BAR AND IRON: Remove all grease, dirt and other surface contaminants.Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer
Product Description gel accumulator 2v 800ah (OPzV800-2) OPZV800-2 Opzv Series Valve Regulated Lead Acid batteries are designed with a proven combination of GEL and Tubular technologies to offer a very high level of reliability. Opzv batteries benefit from an optimized plate design which gives capacities in excess of the DIN standard values. In addition, this series offers both a longest float life and a high cycle life in widely industrial field. Safety and Sealed No electrolyte leakage will occur from terminals or case or case of any Storace Battery ensuring safe and efficient operation. Maintenance-Free operation There is no need to add water thanks to unique gas recombination system which totally transforms the generated gas into water. Storace batteries do not need the equalizing charge As a result of monomer battery's interface resistance capacity and float voltage uniformity are fine. No Free Acid The special electrolyte retentive separators bold the acid and thus there is no free acid inside the battery, and therefore the battery can be mounted in any position. Long life Design The use of heavy -duty lead-calcium alloy grids with anti-corrosive construction enables the Storace AGM battery to remain in float service for 10-15 years; the GEL battery to remain in float service for 15-20 years. The cycle life can be more than 1000 cycles High Reliability and stable quality With advancing AGM and GEL production technology and strictly quality control system, the battery quality is stable and the battery performance is reliable. The voltage, capacity and seal are 100% tested on line. Self-discharge The self-discharge rate in room temperature is approximately 2% of nominal Capacity per month. Operating temperature TheStorace Battery can be operated between -40�°C to +65�°C.The battery can give out over40% fo nominal capacity at -40�°C.
