Printed Circuit Board Assembly Test Probe Pogo Pin PQ75 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ75 series here. Its test center is 75 mil. The diameter is 1.02 mm and the total length is 33.02 mm. Various tip styles, for example, H, K, L, BK, etc., are available for test probes. There are three types of receptacles, namely CR, SC and WW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 112/150/198 gf (4/5.5/7 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
Test Probe Pogo Pin PL50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PL50 series here. Its test center is 50 mil, namely 1.27 mm. The diameter is 0.68 mm and the total length is 27.53 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles, namely CR, VCR, SC, VSC, CRW and VCRW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: Diameter 0.95 mm Full Stroke: 3.7 mm Rated Stroke: 2.54 mm Spring Force: 28/56/85 gf (1/2/3 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper/SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Test Probe Pogo Pin P166 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P166 series here. Its diameter is 1.66 mm and the total length is 48.4 mm. Various tip styles, for example, B3, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 5 mm Spring Force: 500 gf (11 oz) Materials Contact Barrel: Brass, Nickel Plated Spring: Music Wire, Nickel Plated Plunger: Steel, Nickel Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
We KAPADIYA EXPO COMPANY like to offer our clients an extensive array of Fresh Mango, Mango slices, Mango pulp & Mango juice, that is highly appreciated in the market for its quality and taste. Our clients can avail from us an excellent quality of Mangoes. Keeping in mind the varied needs of our clients, we offer an entire range of different packaging options at affordable prices. Our quality examiners execute a series of tests on different parameters, to ensure the quality of the entire array. It has a rich flavor, is hygienically processed & Long shelf life. mangoes are used for the production of jams, marmalades, jelly, sweets, drinks, and fillings of baked goods. It is used in various dishes as a flavoring agent. The mango is tasty, healthy, and flavorsome. Mangoes are rich in boasting high levels of vitamins a, c, and e, soluble fiber, pectin, and unique flavonoids such as mangiferin. mangoes are among the most widely consumed fruits in the world. We provide the Indian best types of mangoes like ALPHONSO'S, KESAR, TOTAPURI, BADAMI, and many more Health Benefits of Mangoes: Mangoes contain many VITAMINS, it is gives ENERGY, SUGAR, PROTEIN & WATER to our body. Mango is high in nutrients â?? particularly VITAMIN C, which aids immunity, and iron absorption. This fruit is not only delicious but also boasts an impressive nutritional profile. Mango is a good source of folate, several vitamins B, as well as VITAMINS A, C, K & E, all of which help boost immunity. Mango contains magnesium, potassium, and the antioxidant MANGIFERIN, which all support healthy heart function
Containers shall comply with following in their latest editions : 1) ISO/TC-104 668 - Series 1 freight containers-Classification, external dimensions and ratings 6346 - Coding, identification and marking for freight containers 1161 - Specification of corner fittings for series 1 freight containers 1496/1 - Specification and testing of series 1 freight containers. Part 1 : General cargo containers for general purposes 830 - Freight containers-Terminology. 6359 - Freight containers-Consolidated data plate 2) The International Union of Railway (UIC) code 592 OR. 3) The Customs Convention on the International Transport of Goods(TIR). 4) The International Convention for Safe Containers (CSC). 5) Transportation Cargo Containers and Unit Loads Quarantine Aspects and Procedures by Commonwealth of Australia Department of Health. (TCT) 6) provide certificates from classification society (BV, ABS, GL, CCS, LR, KR). The specifications of 20â?? one side full access containers: 1 Dimension External Dimensions Internal Dimensions Length 6,058 ( 0, -6 ) mm 5,898 ( 0, -6 ) mm Width 2,438 ( 0, -5 ) mm 2,288 ( 0, -5 ) mm Height 2,591 ( 0, -5 ) mm 2,254 ( 0, -5 ) mm 2 End Door Opening Width .................. 2,280 ( 0,-5 ) mm Height ................... 2,140 ( 0,-5 ) mm 3 Side Door Opening Width .................. 5,700 ( 0,-5 ) mm Height ................... 2,140 ( 0,-5 ) mm 4 Fork Pocket Width .................. 360 mm Height ................... 115 mm Center distance ....... 2,080 mm 5 Inside Cubic Capacity 30.5 cu.m 6 Rating Maximum Gross Weight .............. 24,000 kg Maximum Payload ............. 20,850 kg Tare Weight ............... 3,150 kg
In-circuit Test Probe Pogo Pin P078 Series for Printed Circuit Board Assembly In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P078-BK-346 series here. The diameter is 0.78 mm and the total length is 34.6 mm. Various tip styles, for example, BK, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.9 mm Rated Stroke: 4.6 mm Spring Force: 200 gf (7 oz) at load 4.6 mm Materials Contact Barrel: Phosphor Bronze, Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: SK4, Au on Ni Plated Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
The Ciptadent Classic toothbrush series has now been refined with a new brush handle shape, which is more effective in the process of brushing teeth. Ciptadent Classic comes with a brush head shape and bristle formation that has been clinically tested and developed in Japan, capable of working optimally and effectively in cleaning teeth. Available in 2 variants: -Regular (soft & medium) -Double Action (soft & medium) size: -single 72 pcs -family (3pcs) x 6 pack/ctn-6ctn/box
The Ciptadent Charcoal Protection toothbrush series has now been refined with a new brush handle shape, which is more effective in the process of brushing teeth. The combination of the two colors makes the shape of the Ciptadent Clean toothbrush handle look more attractive. Tested and developed in Japan, and technically proven to be able to work optimally and effectively in cleaning teeth. Variant Charcoal Protection soft. Size: single 72 pcs
Semiconductor Test Probe Pogo Pin SCPC035 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC035 we will introduce is 0.35 mm in barrel diameter and 7.7 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.5 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.5 mm, the loaded force is about 18 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel Phosphor Bronze, Au on Ni Plated Bottom Plunger Beryllium Copper, Au on Ni Plated Top Plunger Beryllium Copper, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 2.5 amps Contact Resistance 100 milliohms max Bandwidth 5.8 GHz at -1dB Inductance 1MHZ at -0.01039 uH Captance 1MHZ at 2.35287 uF Specifications: Full Stroke 1 mm Rated Stroke 0.5 mm Spring Force 18 �±5 gf at load 0.5 mm Mechanical Life about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPA030 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA030 we will introduce is 0.3 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 10 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.1 GHz at -1dB Inductance: 1MHZ at -0.02524 uH Captance: 1MHZ at 1.12735 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 10 ±3 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin P085 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P085 series here. Its diameter is 0.82 mm and the total length is 37 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 2 mm Spring Force: 130 gf (5oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Semiconductor Test Probe SCPA025 Series for IC Test Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA025 we will introduce is 0.25 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 14 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel�¯�¼? Ph/SP, Au on Ni Plated Bottom Plunger�¯�¼? BeCu, Au on Ni Plated Top Plunger BeCu, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 1 amp Contact Resistance 100 milliohms max Bandwidth ? 9.3 GHz at -1dB Inductance 1MHZ at -0.02384 uH Captance 1MHZ at 1.06747 uF Specifications: Full Stroke 1.1 mm Rated Stroke 0.65 mm Spring Force 4 gf at load 0.65 mm Mechanical Life about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Single-headed Pogo Pin Test Probe PQ50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ50 series here. Its diameter is 0.78 mm and the total length is 34.6 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 60 milliohms Mounting Hole Size: Diameter 1 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 85 gf (3 oz) /122 gf (4 oz)/ 150 gf (5.5 oz) at load 4.3 mm Materials Receptacle: Phosphor Bronze, Au on Ni Plated Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: Music Wire, Au on Ni Plated Plunger: Beryllium Copper, Gold Plated or Nickel Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Test Probe Pogo Pin PL75 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PL75 series here. Its test center is 75 mil. The diameter is 1.02 mm and the total length is 27.83 mm. Various tip styles, for example, H, K, L, BK, etc., are available for test probes. There are roughly six types of receptacles, namely CR, VCR, SC, VSC, WW and VWW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 4 mm Rated Stroke: 2.54 mm Spring Force: 113 gf (4 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper/SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cpu Ceramic Processor Scrap with Gold Pins CPU Ceramic Processor Scrap Gold Recovery Wholesale We have a very good quality high yield Cpu Ceramic Scrap for gold recovery We offer a wide range of high yield gold recovery for computer scrap products and below is a list of the CPU scrap types we have Intels 486 386 Cpu Intels I960 Motorola Cpu Intels Pentium Pro Cpu AMD 486 586 Cpu Gold Top Cpu Gold Top Bottom Cpu Intel Pentium 1 DLP Cpu Computer CPU Scrap Scrap Ceramic CPU Scrap Ceramic CPU with Aluminum Cap Scrap Black Plastic CPU Scrap Plastic CPUs Ceramic Pentium pro CPU 486 ceramic Huge Gold Quantity Intel 186 286 386 486 Pentium Pentium Pro i86 i960 Cyrix 486 586 MIIIBM 486 586 686 Motorola 68000 88000 series NEC Toshiba MIPS series R4000 R8000 R10000 R12000 GOLD RECOVERY FROM CERAMIC PROCESSORSScrap CPU Gold recovery from Cpu Ceramic Scrap is a very easy and profitable business Ceramic processors have a good ratio of gold Different processors have different quantities of gold Some types of ceramic processors are below Cpu Scrap recycling method is so easy You can easily recover gold and silver and make money For these processors you dont need to prepare anything like ic chips you will need to remove them from electronics boards first Minimum Order Cpu Ceramic Processor Scrap 500 Kilograms
Product Description gel accumulator 2v 800ah (OPzV800-2) OPZV800-2 Opzv Series Valve Regulated Lead Acid batteries are designed with a proven combination of GEL and Tubular technologies to offer a very high level of reliability. Opzv batteries benefit from an optimized plate design which gives capacities in excess of the DIN standard values. In addition, this series offers both a longest float life and a high cycle life in widely industrial field. Safety and Sealed No electrolyte leakage will occur from terminals or case or case of any Storace Battery ensuring safe and efficient operation. Maintenance-Free operation There is no need to add water thanks to unique gas recombination system which totally transforms the generated gas into water. Storace batteries do not need the equalizing charge As a result of monomer battery's interface resistance capacity and float voltage uniformity are fine. No Free Acid The special electrolyte retentive separators bold the acid and thus there is no free acid inside the battery, and therefore the battery can be mounted in any position. Long life Design The use of heavy -duty lead-calcium alloy grids with anti-corrosive construction enables the Storace AGM battery to remain in float service for 10-15 years; the GEL battery to remain in float service for 15-20 years. The cycle life can be more than 1000 cycles High Reliability and stable quality With advancing AGM and GEL production technology and strictly quality control system, the battery quality is stable and the battery performance is reliable. The voltage, capacity and seal are 100% tested on line. Self-discharge The self-discharge rate in room temperature is approximately 2% of nominal Capacity per month. Operating temperature TheStorace Battery can be operated between -40�°C to +65�°C.The battery can give out over40% fo nominal capacity at -40�°C.
Battery Contact Probe Test Pogo Pin BIP48 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP48 series of battery contact probes. The outside diameter is usually 4.8 mm and total length is 6.8 mm. There are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 5.95 mm (235 mil) Current Rating: 5 Amps, continuous Contact Resistance: 30 milliohms (Maximum) Full Stroke: 2.15 mm Rated Stroke: 1.27 mm Spring Force: 23 gf (0.8 oz)/ 56 gf ( 2 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Brass, Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Gold-plated Probe Pogo Pin PE100(90) Series for In-circuit Test In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE100(90) series here. Its test center is 100 mil. The diameter is 1.36 mm and the total length is 34 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 30 milliohms Mounting Hole Size: Diameter 1.75 mm Full Stroke: 6.5 mm Rated Stroke: 4.3 mm Spring Force: 284 gf (10 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-ended Pogo Pin Test Probe SCPA058 Series for Semiconductor Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA058 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3.5 Amps Contact Resistance: 100 milliohms, max Bandwidth: 8.5 GHz at -1dB Propagation Delay: 21 ps Inductive Reactance: 1MHZ at -0.02506 uH Capacitive Reactance: 1MHZ at -1.01245 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 25�±7 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
