Oilfield drill pipe clean wiper Product Description Oilfield drill pipe clean wiper are designed to place around the pipe to remove mud and debris from the pipe to provide safer handling of the pipe and a cleaner and a safe rig floor. The drill pipe wipers manufactured by us are made of a long lasting, durable rubber compound that is resistant to mud, water and oil based drilling mud. Application: 1. Drilling rig 2. Work over rig 3. Swabbing unit Item Parameters Material of pipe wiper Natural rubber, nitrile rubber Usage Oilfield drilling pipe Hardness. Shore A 60 +/- 5 Tensile strength. MPA 16 Elongation at break. % 460 Inner diameter. 2 3/8" to 7" Outer diameter. 9" to 26" Types of pipe wiper Flat type, dual type and dual split type
Drilling and civil engineering bentonite is made by API and OCMA standardIt can be used as low solid phase mud in under ground civil engineering and drilling field  The specifications Item Mud  yieldM3T Filter  loss ML30min Yield  1b100ft2 Moisture  Wet Sieve Analysis0074mm gel strength HH01 18 12 3xPV 12 4 18 25 40 HH02 1218 1218 3xPV 12 4 15 20 30
Oilfield drill pipe clean wiper are designed to place around the pipe to remove mud and debris from the pipe to provide safer handling of the pipe and a cleaner and a safe rig floor. The drill pipe wipers manufactured by us are made of a long lasting, durable rubber compound that is resistant to mud, water and oil based drilling mud. Application: 1. Drilling rig 2. Work over rig 3. Swabbing unit Item Parameters Material of pipe wiper Natural rubber, nitrile rubber Usage Oilfield drilling pipe Hardness. Shore A 60 +/- 5 Tensile strength. MPA 16 Elongation at break. % 460 Inner diameter. 2 3/8" to 7" Outer diameter. 9" to 26" Types of pipe wiper Flat type, dual type and dual split type No. Product Description Bore Size Material 1 Low profile pipe wiper 9" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 2 Flat solid pipe wiper 9" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 3 Flat solid pipe wiper 12" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 4 Low profile pipe wiper 14" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 5 Flat solid pipe wiper 14" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 6 Split dual pipe wiper 14" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 7 Flat solid pipe wiper 17" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 8 Split dual pipe wiper 17" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 9 Flat solid pipe wiper 19" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber 10 Split dual pipe wiper 19" 2 3/8, 2 7/8, 3 1/2 and 5 Natural, Nitrile Rubber Main Features 1) Remove fluids and debris from pipe. 2) Reduce fluid spillage on rig floor. 3) Steel ring molded in place for added support. 4) Oil resistant, temperature resistant, wear resistant. 5) tear resistant, acid & alkali resistant, anti-corrosion, etc .
En590, jet fuel a1, pet coke, pump, valve, cosmetic, mechanical seal, cotton bag, glass bottle, hand sanitizer, hydraulics, cosmetic bottles,socks, paper drink straw, alcohol wipe, other korean products, mask, or nitrile gloves and hand sanitizer and korean cosmetics.
Rubber Drill Pipe Wiper Product Description Detailed introduction: 1. Drill Pipe Wiper 2. Drill Pipe Wipers are made of specially designed rubber compound having tremendous resistance to cutting, tearing and abrasion. They are available for water based and oil based drilling mud. Designed for application.They are available for 5", 3.1/2", 2.3/8" and 2.5/8" drill pipes / tubings. 3.Size for 27/8",31/2" 5" 51/2"drill pipe 4.wiper is designed to clean casing,tubing in oilwell . Advantages: 1. high strength- Resistance, wear- Resistance 2. Resistance to high temperature 3. Absorption oscillation resistance to high speed 4. Resistance to heavy load 5. Internationally advanced quality level, can be designed to meet the specific needs Description: Material: Butyronitrile rubber is the basic material. The inner steel skeleton is to prevent deformation. Main application: prevent drilling fluid returning from the drilling. Clear drilling fluid on the drill pipe wall to prevent the corrosion of metal. Hardness: 8 to 95 ±5 shore A ,±3 shore A tolerance specially Color: for rubber, usually black, for silicone, can be in any color as you want Machine type: 50 to 400 tons Mold/samples lead-time: For prototype mold, usually in 7days For mass production mold, usually in 2 weeks For some special molds, can be in 30 days, especially for some automotive rubber molds
Couplings, gearbox, valves, pumps, bearings, conveyor systems, pipes & fittings, automation drives electrical items, rtd, cables, switchgears, transformers, measuring instruments, drilling machines. ball valves, gate valves, globe valves, butterfly valves, diaphragm valves, waffle valves, sluice valves, hydraulic valves, pneumatic valves, solenoid valves, bellow seal valves, check valves in stainless steel, ss 304, ss 316, brass, m.s, cast iron, cast steel, pvc, nylon, teflon, ceramic lining valves. fittings: flanges, elbows, tee, couplers, nipples. bearings, v belts, couplings: gear couplings, pin bush couplings,pulleys.Export, clearance, door delivery, import, automations, maintenance, retro fitting, installations
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Auto spare part, automobile tire (suv, truck, tractor, excavator and other), construction machinery and equipment (telehandlers, forklift, generator), mining machinery (drilling, jaw crusher and other), pipes and fitting, ceramic tiles, wpc products, photovoltaic panels, inverters.Exporting, quality control, international logistics and consulting/negotiation
Ferrous: hms 1/2, used rails r50, r65. used drill pipes. nonferrous :copper cathodes, aluminium ingots a7, lead ingots, zinc ingots. minerals : iron ore, copper ore concentrate, lead ore concentrate, zinc ore concentrate, manganese ore, nickel ore. metallurgical coke, petroleum coke. steam coal. agriculture food: all grade rice, wheat, soya beans, sunflower oil, virgin olive oil. petroleum products : diesel fuel, gasoil, jet fuel ai, jet fuel 54. en500, d2, d6..
Bamboo cups are completely biodegradable and do not create harmful substances for the environment. Bamboo cup products are the replacement for traditional plastic cups, glass pipes or straws. Let's join hands to use clean, environmentally friendly products. Bamboo cup is made from natural bamboo, the bottom of the cup sticks out naturally of the bamboo. Therefore, the bottom of the cup is not as flat as a glass or plastic cup. Specification: Product name: Bamboo drinking cup Material: 100% Natural bamboo Size and design: S, M, L or as customer's request Color: Natural bamboo color Feature: Eco-friendly, Durable
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Specification: 1. Drill Pipe Wiper 2. Drill Pipe Wipers are made of specially designed rubber compound having tremendous resistance to cutting, tearing and abrasion. They are available for water based and oil based drilling mud. Designed for application.They are available for 5", 3.1/2", 2.3/8" and 2.5/8" drill pipes / tubings. 3.Size for 27/8",31/2" 5" 51/2"drill pipe 4.wiper is designed to clean casing,tubing in oilwell . Advantages: 1. high strength- Resistance, wear- Resistance 2. Resistance to high temperature 3. Absorption oscillation resistance to high speed 4. Resistance to heavy load 5. Internationally advanced quality level, can be designed to meet the specific needs. Description: Material: Butyronitrile rubber is the basic material. The inner steel skeleton is to prevent deformation. Main application: prevent drilling fluid returning from the drilling. Clear drilling fluid on the drill pipe wall to prevent the corrosion of metal. Hardness: 8 to 95 ±5 shore A ,±3 shore A tolerance specially Color: for rubber, usually black, for silicone, can be in any color as you want Machine type: 50 to 400 tons Mold/samples lead-time: For prototype mold, usually in 7days For mass production mold, usually in 2 weeks For some special molds, can be in 30 days, especially for some automotive rubber molds
We are interested to supply 200 MT of Post Industrial Soft Mix Color Pvc Pipe Regrind. PVC Grey Pipe Regrind Place of Origin: : JAPAN, US, EUROPE Materials: : Polyvinyl Chloride [PVC] Color : Grey Application : Water Pipe, Window, Board, Contruction... Grade : Extrusion K65-67 Type : Post Industrial Waste Quality : Clean and less than 3% shortage Form : Regrind Unit : Ton/Tons FOB Price : $400.00 - $600.00 Minimum Order : 25 Tons Payment Term : T/T 50/50 and L/C 100% at sight Estimate Lead Time : 15 - 20 days Origin : Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity : 200 tons/month Packaging : Jumbo Bag
Carbon fish meat grill oven process: A. special high temperature resisitant material,high heat deformation,the overall structure uses professtional plate ; B.all into oxygen at the bottom of the damper desigh,fast burning heat rapidly ,at teh top of the air valve design,effective control of heat loss; C. origianl putty separation technology,completely avoiding using process because of the putty mixed soot and open flame,ensure clean,health and safety ; D.equipment applied double high temperature heat insulation material,insulation system,insulation with security,external direct touch with no hidden dangers. Operation method: A. all burning charcoal in the burning charcoal ,open at the top the smooke at the bottom of the mouth and damper; B.charcoal burning closed 10 minutes to the degree of smoke-free smoke at the top of the mouth,the heat; C.after the temperature reaches the standard,in the baking objects to buy object ; D.5-10minutes,bake fish until brown on both sides,are taken from the furnace, the plate feeding . Equipment advantages : A. unique design principle ,the use of charcoal smoke all gathered in the grilled fish inside furnace,through the top of the exhaust pipe directly emitted; B.rapid heat,guarantee the production speed,let the charcoal furnace cavity fully burning rapied heating up,wind valve,and through the top to the bottom of the design of air supply outlet temperature in the furnace in a 300-350 degree,put the fish in the distribution on the stove on content cabinet ,only 8-10 minutes can be produced; C. a novel view and admire a gender ,the design of the gear type appeared in front of customers,the grilled fish process more transparent,more ornamental ,fish and clients directly face to face "communication " ; D this design flexibility ,the real achieve a multi-purpose furnace, can bakering chicken duck cattle and sheep for equipment use diversification more rich . Fuel: dual-use carbon box ,burning charcoal or alcohol (vegetable oil ) ,pump design. Installation and commissioning Overall production : have direct admission requiements,no installation commissioning ,one pace reachs the designated position . 1.Solve the smoke problem charcoal grilled fish we are familiar with most of the fish appeared in the night street food stalls ,a rectangular fish furnace ,a big fan, the air is filled with smoke smell fish .
We are ready to export 200 tons of Grey PVC Pipe Regrind on a continuous monthly basis. We wish to work with the reliable PVC Regrind buyers from worldwide. Place of Origin : JAPAN, US, EUROPE Materials : Polyvinyl Chloride [PVC] Color : Grey Application : Water Pipe, Window, Board, Contruction... Grade : Extrusion K65-67 Type : Post Industrial Waste Quality : Clean and less than 3% shortage Form : Regrind Unit : Ton/Tons FOB Price : $400.00 - $600.00 Minimum Order : 25 Tons Payment Term : T/T 50/50 and L/C 100% at sight Estimate Lead Time : 15 - 20 days Origin : Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity : 200 tons/month Packaging : Jumbo Bag
We are ready to export 200 tons of Grey PVC Pipe Regrind on a continuous monthly basis. We wish to work with the reliable PVC Regrind buyers from worldwide. Place of Origin : JAPAN, US, EUROPE Materials : Polyvinyl Chloride [PVC] Color : Grey Application : Water Pipe, Window, Board, Contruction... Grade : Extrusion K65-67 Type : Post Industrial Waste Quality : Clean and less than 3% shortage Form : Regrind Unit : Ton/Tons FOB Price : $400.00 - $600.00 Minimum Order : 25 Tons Payment Term : T/T 50/50 and L/C 100% at sight Estimate Lead Time : 15 - 20 days Origin : Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity : 200 tons/month Packaging : Jumbo Bag
We are interested to supply 200 MT of Soft Mix Color Pvc Pipe Regrind on a regular monthly basis. PVC Soft Mix Color Place of Origin: :JAPAN, US, EUROPE Materials: :Polyvinyl Chloride [PVC] Color :Mix Color Application :Sheet, Board, Bag, Packaging, Floor, Wall... Grade :Flexible Type :Post Industrial Waste Quality :Clean and less than 3% shortage Form :Roll, Sheet Unit :Ton/Tons Minimum Order :25 Tons Payment Term :T/T 50/50 and L/C 100% at sight Estimate Lead Time :15 - 20 days Origin :Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity :200 tons/month Packaging :Jumbo Bag FOB Price :$500.00 - $700.00 Minimum Order : 25 Tons Payment Term : T/T 50/50 and L/C 100% at sight Estimate Lead Time : 15 - 20 days Origin : Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity : 200 tons/month Packaging : Jumbo Bag Interested PVC Soft Mix Color Pipe Regrind buyers, please do contact us. We are waiting to hear from you.