Microstep Driver Leadshine MA860H DM1182 Stepper Motor Driver Tips: Another good choice on driver is YAKO stepper motor driver. Features of MA860H stepper driver: 1) Good high speed performance 2) Output voltage is Max. 80VAC 3) Output current is Max. 7.2A 4) Self-adjustment technology 5) Pure-sinusoidal current control technology 6) Pulse input frequency is up to 300 KHz 7) TTL compatible and optically isolated input 8) Automatic idle-current reduction 9) 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev 10) Suitable for 2-phase and 4-phase motors 11) Support PUL/DIR and CW/CCW modes 12) Short-voltage, over-voltage, over-current and short-cicuit protection
Stepper driver controls the stepper motor moving, move direction and moving steps. Step driver micro the motor steps, so ensure the precision. CNC driver is widely used on CNC router, cnc laser machine, cnc plasma cutting machine, cnc wood lathe machine, etc. Besides cnc machines, we also supply original Yako drivers and Leadshine drivers to support our customers. Leadshine series we have these models: DMA860H DM856 DM542-05 DM442 DM1182 Yako series we have: YKD2608MH YKA2811MA If any other requests, also can contact with us. We will do our best to support you.
Introduction The d2hb882mb is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80vdc Suitable for-2-phase and 4-phase motors Output current up to 5.86a Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200khz Automatic idle-current reduction Small size (107*97*48), weight:1kg
Introduction The d2hb542ma is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque Supply voltage up to +45vdc Output current up to 5.86a Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200khz Dip switch current setting 8 different values Small size (122.2*90*33), weight:0.3kg
SD-2H086MB Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80VDC Suitable for-2-phase and 4-phase motors Output current up to 5.86A Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200KHz Automatic idle-current reduction Small size (107*97*48),Weight:1KG
SD-2H044MA Features Low cost and good high-speed torque Supply voltage up to +45VDC Output current up to 5.86A Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200KHz Dip switch current setting 8 different values Small size (122.2*90*33),Weight:0.3KG
Q2HB88M Features (1) High performance, low price (2) Two group 32 channels constant angel and constant torque subdivision. Highest subdivision: 480 (3) The motor phase current is reduced to set current value 100 ms after receiving the last pulse edge (4) Bipolar constant current chopping circuit (5) Opto-isolated input/output (6) Driven current is adjustable continuously from 0.5A/phase to 8A/phase (0.4A/phase to 6.4A/phase) (7) Single power supply, voltage arrange from DC24/V to 80V (DC40V to130V) (8) Highest response frequency: 200Kpps (9) Over voltage protection, overheat protection, over current protection
Constant angle, constant torque micro step driver, the drive voltage of which is from 12V to 40VDC. It is designed for use with 2 phase hybrid stepper motor of all kinds with 42mm to 57mm outside diameter, 6, 8 leads, regulated phase current from 0.5A to 3A. The unique control circuit that it adopts can reduce motor¡¯s noise, make motor run more smoothly, improve motor's performance by 30% at high speed, reduce driver¡¯s heating by 50%. It is widely used in small size of numerical control devices with higher resolution such as carving machine, laser labeling machine, inner laser curving machine and etc. FEATURES * 4 channels constant angle and constant torque micro step, highest micro step: 64 * Highest response frequency: 200Kpps * Current of winding will be reduced by approximately 50% when no step pulse command is received for 0.1 second * Bipolar constant current chopping mode * Opto-isolated signal I/O * Drive current is continuously adjustable from 0.5A/phase to 3A/phase * Single power supply voltage from 12V to 40VDC.
The DVS278 is full digital 2 phase stepper driver based on DSP control. The drive voltage of which is from 24V to 80VDC. It is designed for use with the 2 phase hybrid stepper motor of all kinds with 57mm to 86mm outside diameter, regulated phase current from 2.0A to 7.2A. The highest micro step is 40000ppr. It is widely used in small size numerical control devices such as curving machine, packing machine, CNC and etc. FEATURES * 16 channels constant angle, constant torque micro steps, highest micro step: 40000ppr * Highest response frequency: 200Kpps * Current of winding will be reduced by approximately 50% when no step pulse command is received for 1.5 second * Opto-isolated signal I/O * Drive current is adjustable in 16 channels from 2.0A/phase to 7.2A/phase * Single power supply from 24V to 80VDC.
The DVS2811 is full digital 2 phase stepper driver based on DSP control. The drive voltage of which is from 40V to 110VAC. It is designed for use with the 2 phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter, regulated phase current from 0.5A to 8.0A. The circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly without noise and vibration. The highest micro step is 40000ppr. It is widely used in small size numerical control devices such as curving machine, packing machine, CNC and etc. FEATURES * 16 channels constant angle, constant torque micro steps, highest micro step: 40000ppr * Highest response frequency: 200Kpps * Current of winding will be reduced by approximately 50% when no step pulse command is received for 1.5 second * Opto-isolated signal I/O * Drive current is adjustable in 16 channels from 0.5A/phase to 8.0A/phase * Single power supply from 40V to 110VAC * Phase terminal memory function (motor phase terminal is memorized after input pulse train stopping 3s and it is recovered when stepper driver power on or signal MF changes from low level to high level).
The DVS368 is full digital 3 phase stepper driver based on DSP control. The drive voltage of which is from 24V to 80VDC. It is designed for use with the 3 phase hybrid stepper motor of all kinds with 57mm to 86mm outside diameter, regulated phase current from 2.5A to 6.2A. The highest micro step is 60000ppr. It is widely used in small size numerical control devices such as curving machine, packing machine, CNC and etc. FEATURES * 16 channels constant angle, constant torque micro steps, highest micro step: 60000ppr * Highest response frequency: 200Kpps * Current of winding will be reduced by approximately 50% when no step pulse command is received for 1.5 second * Opto-isolated signal I/O * Drive current is adjustable in 16 channels from 2.5A/phase to 6.2A/phase * Single power supply from 24V to 80VDC * Phase terminal memory function (motor phase terminal is memorized after input pulse train stopping 3s and it is recovered when stepper driver power on or signal MF changes from low level to high level).
The DVS3722 is full digital 3 phase stepper driver based on DSP control. The drive voltage of which is from 110V to 220VAC. It is designed for use with the 3 phase hybrid stepper motor of all kinds with 57mm to 130mm outside diameter, regulated phase current from 1.3A to 7.0A. The circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly without noise and vibration. The highest micro step is 60000ppr. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, computer embroider machine, packing machine and etc. FEATURES * 16 channels constant angle, constant torque micro steps, highest micro step: 60000ppr * Highest response frequency: 200Kpps * Current of winding will be reduced by approximately 50% when no step pulse command is received for 1.5 second * Opto-isolated signal I/O * Drive current is adjustable in 16 channels from 1.3A/phase to 7.0A/phase * Single power supply from 110V to 220VAC * Phase terminal memory function (motor phase terminal is memorized after input pulse train stopping 3s and it is recovered when stepper driver power on or signal MF changes from low level to high level).
PMD006P3E is a kind of micro integrated stepper motor microstepping driver, which can be directly installed in the rear 42/57/86 etc series stepper motor, and which has the advantages of small size, strong driving force, and low heat and so on. PMD006P3E stepping motor driver can provide 0~6 continuous adjustable peak current, maximum 128 microstepping, free current which can be adjusted continuously.
Export European quality!
Q2hb34ma is a constant angle and constant torque stepper drive. The drive voltage range from dc12v to 40v. It can match 2-phase hybrid stepper motors whose rated current is under 3a and shaft diameter range from 42mm to 86mm. Owe to bipolar constant chopping circuit, it can make motors low noise, operated smoothly. It is widely used in the small size of numerical control device with higher resolution such as carving machine, laser labeling machine, inner laser curving machine and etc. Features high performance, low price 4 channels constant angel and constant torque subdivision, the highest subdivision: 64 highest response frequency: 200kpps the motor phase current is reduced to approximately 50% of the set current value 100ms after receiving the last pulse edge bipolar constant current chopping circuit opto-isolated input/output driven current is adjustable continuously from 0.5a/phase to 3a/phase single power supply, voltage arrange from dc12 to 40v. Size:136x82x25mm Weight:0.5kg
We are a manufacturer and can manufacture products according to our customer's design. Currently we are looking for qualified stocking distributors with competitive price and good discount in the world for mutually beneficial long-term relationship. We try our best to support our distributors and business partners to develop more market percentage. Please join us, let's create the glorious future together!
"The stepper driver has the advantages of miniature size, strong driving force, low heat dissipation, it can provide 0-5A peak current per phase. Main features of the integrated stepper driver Gecko are as following: Wide range of 12-36V single voltage supply Output current 1.5-5A Adjustable phase current by commands Common cathode signal,Common anode signal,Differential sign,Double pulse,pulse n direction,and other input methods P2 Max 32VDC, 2A per phase Support full, half, 4/8/16/32/64/128 microstepping resolution P3 Max 32VDC, 3A per pahse, full, half, 1/4, 1/8 and 1/16 microstepping P6 Max 6A per phase Support full, half, 4/8/16th microstepping Support 4/6/8 wires two phase stepping motor Frequency is the highest 250Khz TSD, UVLO, OCP protection Idle current can be adjusted continuously Support full torque mode for torque enhancement"
DM420 drive, and 42BYGH stepper motor with the use of Brand: ACT Product type: DM420 type DM420 type subdivision driver of two phase hybrid stepping motor drive, with 12 ~ 36V DC power supply, suitable for driving voltage of 24V ~ 36V, current is less than 2.0A diameter 42 ~ 57 mm two-phase hybrid step motor. The current loop driver adopts AC servo drive subdivision control, motor torque fluctuation a small, low speed operation is very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. I. overview DM420 type subdivision two-phase hybrid stepper motor drive, with 12 ~ 36V DC power supply, suitable for driving voltage of 24V ~ 36V, current is less than 2.0A diameter 42 ~ 57 mm two-phase hybrid step motor. The current loop driver adopts AC servo drive subdivision control, motor torque fluctuation is small, low speed operation very smooth, almost no vibration and noise. High speed torque is also much higher than other phase drives, high positioning accuracy. Widely used in engraving machine, CNC machine tools, packaging machinery demand higher resolution devices. 1 average current control, two phase sinusoidal current drive output 2 DC 12 ~ 36V power supply 3 opto isolated signal input / output 4, overvoltage, undervoltage, overcurrent, interphase short-circuit protection function 5, eight files subdivision and automatic half flow function 6, eight files output phase current setting 7 has the offline command input terminal 8 the torque of the motor is related to its speed, irrespective of the number of steps the motor has to rotate 9 high starting speed 10. high speed torque Input voltage DC 12 to 40V input The input current is less than 2 Amperes The output current is 0.44A to 2.83A Power dissipation: 40W The working temperature is -10 to 45 degrees; the storage temperature is between -40 and 70 centigrade Moisture can not dew or water Gases are prohibited from flammable gases and conductive dust Weight 70 grams
1 PC Closed loop Stepper Motor Nema34 86HBM80-1000-1 6A 900N-cm(1270oz-in) 1 PC Mactching Driver WTSS880 1 pc extra 3 M length cable Technical Specifications Part No.: 86HBM80-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 2.4V Current: 6.0A/phase Resistance: 0.4 Ohm/phase Inductance: 6.5 mH/phase Holding torque: 9N.m 1275oz-in Rotor inertia: 2300g-cm2 Number of wire leads: 4 Weight: 5 kg Length: 142mm
This item inculdes : 1 PC Closed loop Stepper Motor Nema23 57HBM10-1000 4A 110N-cm(155oz-in) 1 PC Mactching Driver WTSS570 Technical Specifications Part No.: 57HBM10-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 1.6V Current: 4.0A/phase Resistance: 0.44 Ohm/phase Inductance: 1.2 mH/phase Holding torque: 1.1N.m 155oz-in Rotor inertia: 300g-cm2 Number of wire leads: 4 Weight: 2 kg Length: 77mm
