SD-2H086MB
Features
Low cost and good high-speed torque
14 selectable resolutions
Supply voltage up to +80VDC
Suitable for-2-phase and 4-phase motors
Output current up to 5.86A
Dip switch current setting 8different values
Optically isolated input signals
Pulse frequency up to 200KHz
Automatic idle-current reduction
Small size (107*97*48),Weight:1KG
Introduction The d2hb882mb is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80vdc Suitable for-2-phase and 4-phase motors Output current up to 5.86a Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200khz Automatic idle-current reduction Small size (107*97*48), weight:1kg
Introduction The d2hb542ma is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque Supply voltage up to +45vdc Output current up to 5.86a Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200khz Dip switch current setting 8 different values Small size (122.2*90*33), weight:0.3kg
SD-2H044MA Features Low cost and good high-speed torque Supply voltage up to +45VDC Output current up to 5.86A Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200KHz Dip switch current setting 8 different values Small size (122.2*90*33),Weight:0.3KG
Q2HB88M Features (1) High performance, low price (2) Two group 32 channels constant angel and constant torque subdivision. Highest subdivision: 480 (3) The motor phase current is reduced to set current value 100 ms after receiving the last pulse edge (4) Bipolar constant current chopping circuit (5) Opto-isolated input/output (6) Driven current is adjustable continuously from 0.5A/phase to 8A/phase (0.4A/phase to 6.4A/phase) (7) Single power supply, voltage arrange from DC24/V to 80V (DC40V to130V) (8) Highest response frequency: 200Kpps (9) Over voltage protection, overheat protection, over current protection
PMD006P3E is a kind of micro integrated stepper motor microstepping driver, which can be directly installed in the rear 42/57/86 etc series stepper motor, and which has the advantages of small size, strong driving force, and low heat and so on. PMD006P3E stepping motor driver can provide 0~6 continuous adjustable peak current, maximum 128 microstepping, free current which can be adjusted continuously.
Export European quality!
Q2hb34ma is a constant angle and constant torque stepper drive. The drive voltage range from dc12v to 40v. It can match 2-phase hybrid stepper motors whose rated current is under 3a and shaft diameter range from 42mm to 86mm. Owe to bipolar constant chopping circuit, it can make motors low noise, operated smoothly. It is widely used in the small size of numerical control device with higher resolution such as carving machine, laser labeling machine, inner laser curving machine and etc. Features high performance, low price 4 channels constant angel and constant torque subdivision, the highest subdivision: 64 highest response frequency: 200kpps the motor phase current is reduced to approximately 50% of the set current value 100ms after receiving the last pulse edge bipolar constant current chopping circuit opto-isolated input/output driven current is adjustable continuously from 0.5a/phase to 3a/phase single power supply, voltage arrange from dc12 to 40v. Size:136x82x25mm Weight:0.5kg
This item inculdes : 1 PC Closed loop Stepper Motor Nema23 57HBM10-1000 4A 110N-cm(155oz-in) 1 PC Mactching Driver WTSS570 Technical Specifications Part No.: 57HBM10-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 1.6V Current: 4.0A/phase Resistance: 0.44 Ohm/phase Inductance: 1.2 mH/phase Holding torque: 1.1N.m 155oz-in Rotor inertia: 300g-cm2 Number of wire leads: 4 Weight: 2 kg Length: 77mm
1 PC Closed loop Stepper Motor Nema34 86HBM80-1000-1 6A 900N-cm(1270oz-in) 1 PC Mactching Driver WTSS880 1 pc extra 3 M length cable Technical Specifications Part No.: 86HBM80-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 2.4V Current: 6.0A/phase Resistance: 0.4 Ohm/phase Inductance: 6.5 mH/phase Holding torque: 9N.m 1275oz-in Rotor inertia: 2300g-cm2 Number of wire leads: 4 Weight: 5 kg Length: 142mm
