Product Usage Programmable time relays include JSBXC-780, JSBXC-820, JSBXC-820, JSBXC1-850, and JSBXC1-870 series relays. Each type of relay has four types of warm-up time to choose from, among which JSBXC1-870 series The heating time can also be changed according to the special requirements of users. The relay is used as a delay control in the circuit. Applicable environment a) Ambient temperature: -5~+40; b) Relatively moderate: not more than 90% (temperature +25); c) Air pressure: not less than 70KPa (equivalent to an altitude below 3000m); d) Vibration: the frame rate is not more than 15Hz, and the amplitude is not more than 0.45mm; e) Rated voltage: DC 24V, voltage fluctuation range 24X (1�±10%) V; f) Working position: horizontal; g) There is no harmful gas causing explosion hazard around, and good dust-proof measures should be applied. Mechanical properties 1614996944256898.jpg Electrical characteristics .jpg Note: The error range of the resistance value of the relay coil is ±(nominal resistance value10%) Time characteristics
Applicable environment a) Ambient temperature: -5~+40; b) Relatively moderate: not more than 90% (temperature +25); c) Air pressure: not less than 70KPa (equivalent to an altitude below 3000m); d) Vibration: the frame frequency is not more than 15Hz, and the amplitude is not more than 0.45mm; e) Rated voltage: DC 24V, voltage fluctuation range 24X (1±10%V; f) Working position: horizontal; g) There is no harmful gas causing explosion hazard around, and good dust-proof measures should be applied. Mechanical properties 1614998643577125.jpg Precautions a) The identification pin numbers of the programmable time relays are the same. Please confirm the corresponding slow suction time of the corresponding type of relay before use. b) Terminals 1, 2, 3, and 4 of the two coils of the relay are directly connected in parallel with the two diodes on the printed circuit; therefore, when measuring the electrical characteristics of the relay, the positive pole of the power supply must be connected to the terminals 1, 3, and the negative pole of the power supply must be connected to the terminals 1, 3. On terminals 2, 4. C) Contacts 11 and 12 are already occupied by the relay, and the number of contacts that can be used by the user is 2QH, 1Q. d) The position of the relay contact system is shown in Figure 1. When in use, the socket must be equipped with an identification pin. e) The use environment of the relay should have good ventilation conditions and dust-proof equipment. And used in specially designed circuits; in special circumstances, the electrical characteristics and contact capacity of the relay should be considered to ensure the reliable operation of the relay.
PC/ABS regrind full container available MATERIAL : PC/ABS regrind full container available CATEGORY : PC/ABS TYPE : Regrind GRADE : Black color SPECIFICATION : 1 full container available Origin : Tunisia LOADING WEIGHT : 23 Ton FOB (USD/Ton:) : 850$ - 1000$ Packaging : Jumbo Bag Est. Shipping Time : 15, 30, 45 days
PC CD DVD without case, cover etc MATERIAL: PC CD DVD without case, cover etc CATEGORY: PC TYPE: Disc SPECIFICATION: whole disc without case, cover etc Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 850$ - 1050$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
POM regrind black color full container available POM plastic possesses the same priority features as other plastic polymers, some of the highlights of the special resin: High hardness Bearing good Low friction number High resistance to abrasion High temperature resistant Less water intake Has anti-static ability Dimensional stability, little change Less smoke burns when burning High glossy surface High crystallization In addition to the priority points, POM plastic also has some limited formats such as: Quality acid resistance and alkali High hatch rate when changing secretions Operation mode Heat range MATERIAL: POM regrind black color full container available CATEGORY: POM TYPE: Regrind GRADE: Black color SPECIFICATION: 1 full container available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS Regrind from post consumer materials Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind from post consumer materials ,Yes No Fr, NO pc abs, no iron, no circuit etc CATEGORY: HIPS TYPE: Regrind SPECIFICATION: Hips from post consumer materials.Yes No Fr, NO pc abs, no iron, no circuit etc. Hips per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS Regrind White-Mix Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind White-Mix CATEGORY: HIPS TYPE: Regrind White-Mix SPECIFICATION Product- HIPS regrind post production from Yogurt caps Contamination â?? up to 2% foil metalizing (cover of the yogurt caps). Food grade material Post - industrial Sheet Extrusion & Vacuum forming Origin: Spain LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
POM Regrind from zipper Teeth, industry lump, industry runner Definition of POM resin (polyformaldehyde resin): polyformaldehyde is a linear polymer without side chain, high density and high crystalline properties. According to different chemical structures in the molecular chain, there are two types of homoformaldehyde and copolymers. of both types of polyformaldehyde density, high crystallinity, melting point, but thermal stability, the treatment temperature range is narrow (about 10oC), slightly lower in acid and alkali stability; The density of formaldehyde, melting point, strength and copolymer is lower, but good thermal stability, not easy to decompose, wide range of treatment temperature (about 50oC), acid and alkali stability are good . Plastic has excellent all-round performance. Good physical, mechanical and chemical properties, especially with excellent friction resistance. It is commonly referred to as steel or strip, which is the general engineering plastic third. Suitable for reducing wear on parts, transmitters, chemicals, tools and other parts. One of the synthetic resins, also known as polyformaldehyde resin, POM resin and steel, etc. This is a kind of white or black plastic resin with high hardness, high steel and high wear resistance. Used for gears, bearings, auto parts, machine tools, tools, etc. MATERIAL: POM Regrind from zipper Teeth , industry lump, industry runner CATEGORY: POM TYPE: Regrind SPECIFICATION: from zipper Teeth , industry lump, industry runner,Qty per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Size: 450*640*850 The Chair Completely Used Of Natural Rubber Wood, Qualifically Dried By Modern Technology To Anti-most Anti-correcting, Warranties By Time. Chair Covered With Pu Glossy Paint (natural) Avoid Waterproof, Easy To Clean, Safe For Users.
Size: 450*640*850 The Chair Completely Used Of Natural Rubber Wood, Qualifically Dried By Modern Technology To Anti-most Anti-correcting, Warranties By Time. Chair Covered With Pu Glossy Paint (natural) Avoid Waterproof, Easy To Clean, Safe For Users.
Size: 850*650*730 The Table Completely Used Of Natural Rubber Wood, Qualifically Dried By Modern Technology To Anti-most Anti-correcting, Warranties By Time. Table Covered With Pu Glossy Paint (natural) Avoid Waterproof, Easy To Clean, Safe For Users.
PA66 GF regrind black color Pa6 / pa66 is mainly applied as follows: 1. Improves nylon water absorption and improves size stability of the product. 2. Improved nylon fire resistance to meet the requirements of electronics, electrical, communications and other industries. 3. Improved mechanical strength of nylon to achieve the strength of metal materials, metal replacement. 4. Improves nylon low-temperature resistance and enhanced resistance to environmental stress. 5. Improves nylon wear resistance to meet high wear resistance requirements. 6. Improves nylon antistatic properties to meet its extraction requirements and mechanical applications. 7. Improves nylon heat resistance to adapt to high temperature conditions such as car engines. 8. Reduce nylon cost and improve product competitiveness. Through the above modification, high performance and functionalization of nylon composite materials are realized, thereby promoting the development of industries involving high performance and high quality. MATERIAL: PA66 GF regrind black color CATEGORY: PA66 GF TYPE: Regrind GRADE: Black color SPECIFICATION: GF50. 1 full container available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 850$ - 1050$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Time relay can be widely used in machines and equipment needing self-control of high precision and reliability. It is characteristic of small size, light weight, compact structure, high dependable and efficient,long life,etc.
Features 1.Intelligent and digital led timer 2.1~4 channels, programmable and arbitrary combination and arbitrary output 3.Memory storage (10years) / mechanical life 4.Wide timing range (1millsecond~9999days) 5.Power supply (220v ac 50/60hz) 6.Capable of maintain timing in power-off state 7.100 groups of programme/time periods Additional jump function, the number of cycle is settable
Features 1.Intelligent and digital led(light-emitting ) timer 2.1~8 channels, programmable and arbitrary combination and arbitrary output 3.Memory storage (10years) / mechanical life 4.Panel mounting 5.Delay time unit:0.1s/1s/1min(option) 6.Power supply (220v ac 50/60hz) 7.Input:transistor 8.100 groups of programme/time periods
1.New high-speed MCU chip with great speed 2.Big capacity of program and stable and reliable operation 3.Accomplishes the control of time-segment, sequential-segment and the program 4.Built-in 100 time relays 5.Be used in programmable fountain, programmable lights, sewerage, water supply, irrigation, bag pulse dust, electric boiler heating, street lights, neon light, water purifier,electric valve (solenoid valve)timing mud, grit removal control and so on. 6.The 220V/1A DC or AC load. 7.16/8-channel output
ENVIRONMENTAL CONDETIONS: Temperature Range: -55~+85 C Relative Humidity: Up to 98% at +40 C Atmospheric pressure: 86kPa~106kPa, Low pressure 4 kPa Vibration: 10~2000Hz, 196 m/s2 Shock: 735m/s2 Acceleration: 490 m/s2. TECHNICAL REQUIREMENTS: Rated Voltage: 12VDC, 18VDC, 24VDC, 27VDC Insulation Resistance: 1000Mohm Dieletric Withstanding Voltage: (RMS/50Hz) 500V Contact Resistance: 0.1ohm Rated Load: 2A28VDC, 4A28VDC Life: 1x105: 1x105 / 2x104 Contact Form: 2C(DPDT); Time Delay: 0.05~500s(Nonadjustable) Outline Dimensions: 20.5 x 10.5 x 15mm Weight: 13g .
Sesame imports from South Africa include several premium varieties, such as TKG-306, SWB-32-10-1 (Savitri), and others. These sesame seeds are exported worldwide, offering diverse options suited for various climates and conditions. Below are some of the key sesame varieties exported from South Africa: 1. TKG-306 Released in 2007, TKG-306 matures in about 86-90 days. The seeds are white and weigh around 2.8 g. This variety is resistant to Phytophthora blight and moderately resistant to Macrophomina, Cercospora, powdery mildew, and Alternaria leaf spot. 2. SWB-32-10-1 (Savitri) Savitri variety contains 48-52% oil and yields around 1200-1500 kg/ha in summer. It matures in about 84-88 days and is recommended for cultivation in West Bengal. 3. Jawahar Til 12 (PKDS-12) Jawahar Til-12 has an oil content of 48-52% and an average yield of 700-750 kg/ha. This variety is suited for summer cultivation in Madhya Pradesh and is moderately resistant to Macrophomina stem/root rot. 4. Gujarat Til-3 Gujarat Til-3 has 48-52% oil content and yields 750-800 kg/ha. It is recommended for the Kharif season in the Saurashtra region of Gujarat, with a maturation time of around 84-88 days. 5. RT-346 RT-346 has oil content ranging from 49-51% and yields 750-850 kg/ha. It is recommended for the Kharif season in various regions such as Rajasthan, Haryana, Punjab, Himachal Pradesh, Gujarat, Uttar Pradesh, and Maharashtra. It matures in about 82-86 days. 6. JLT-408 With an oil content of 51-53%, JLT-408 yields 700-800 kg/ha. This variety is recommended for assured rainfall zones in Khandesh, Vidharba, and Marathwada regions, taking around 80-85 days to mature. 7. TKG-308 TKG-308 has an oil content of 48-50% and an average yield of 700-750 kg/ha. It is moderately resistant to Macrophomina, Cercospora, Bacterial leaf spot, and Leaf curl, and is tolerant to capsule borer. 8. Shubra Shubra sesame has an oil content of 48-52% and yields 800-900 kg/ha. The seeds are golden yellow and are recommended for cultivation in Orissa during both the Kharif and summer seasons. 9. RT-351 RT-351 has oil content ranging from 48-50% and yields 700-800 kg/ha. It is resistant to Macrophomina, Leaf curl, and Phillody, and moderately resistant to Cercospora and capsule borer. This variety is recommended for cultivation in states like Rajasthan, Gujarat, UP, Maharashtra, Haryana, Punjab, and Jammu & Kashmir.
ALSTOM GBCDG61EG040SGCH IDMT TWO O/C & ONE E/F RELAY WITH HIGH-S Relay Technical specification Relay model no CDG61EG040SGCH Relay type CDG 61 Case size 3D HOR. Application 2 O/C & 1 E/F Current setting - O/C 2.5 to 10 amps Aux.Contacts With Flag 3M S/R Output contacts 2M S/R C.T.Secondary 5 amps Frequency 50 Hz Burden 3 VA Operating time 1.3 secs Current setting - E/F 0.5 to 2 amps High set - O/C Setting 20 to 80 amps High set - E/F Setting 5 to 20 amps High set conts.With flag CAG 13 / 2M S/R Name plate RFG9125 903 Outline drawing MFJ 014 Wiring diagram MADZ 821.27-1
ALSTOM GBCDG61EG041SGCH IDMT TWO O/C & ONE E/F RELAY WITH HIGH-S Technical specification Relay model no CDG61EG041SGCH Relay type CDG 61 Case size 3D H 30T Application 2 O/C & 1 E/F Current setting - O/C 2.5 to 10 amps Contacts / Output contacts 3M S/R / 2M S/R C.T.Secondary 5 amps Frequency 50 Hz Burden 3 VA Operating time 3 secs Current setting - E/F 0.5 to 2 amps High set - O/C Setting 20 to 80 amps High set - E/F Setting 5 to 20 amps High set CAG 13 Name plate RFG9126 903 Outline drawing MFJ 014 Wiring diagram MADZ 821.27-1
