Ipp Power Plant Rubber Bladder Nxqa 1 6 20 L A Suppliers and Manufacturers

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

Turmeric is one of nature's most powerful healers. The active ingredient in turmeric is curcumin. Tumeric has been used for over 2500 years in India, where it was most likely first used as a dye. The medicinal properties of this spice have been slowly revealing themselves over the centuries. Long known for its anti-inflammatory properties, recent research has revealed that turmeric is a natural wonder, proving beneficial in the treatment of many different health conditions from cancer to Alzheimer's disease. Here are 20 reasons to add turmeric to your diet: 1. It is a natural antiseptic and antibacterial agent, useful in disinfecting cuts and burns. 2. When combined with cauliflower, it has shown to prevent prostate cancer and stop the growth of existing prostate cancer. 3. Prevented breast cancer from spreading to the lungs in mice. 4. May prevent melanoma and cause existing melanoma cells to commit suicide. 5. Reduces the risk of childhood leukemia. 6. Is a natural liver detoxifier. 7. May prevent and slow the progression of Alzheimer's disease by removing amyloyd plaque buildup in the brain. 8. May prevent metastases from occurring in many different forms of cancer. 9. It is a potent natural anti-inflammatory that works as well as many anti-inflammatory drugs but without the side effects. 10. Has shown promise in slowing the progression of multiple sclerosis in mice. 11. Is a natural painkiller and cox-2 inhibitor. 12. May aid in fat metabolism and help in weight management. 13. Has long been used in Chinese medicine as a treatment for depression. 14. Because of its anti-inflammatory properties, it is a natural treatment for arthritis and rheumatoid arthritis. 15. Boosts the effects of chemo drug paclitaxel and reduces its side effects. 16. Promising studies are underway on the effects of turmeric on pancreatic cancer. 17. Studies are ongoing in the positive effects of turmeric on multiple myeloma. 18. Has been shown to stop the growth of new blood vessels in tumors. 19. Speeds up wound healing and assists in remodeling of damaged skin. 20. May help in the treatment of psoriasis and other inflammatory skin conditions.

Important Note: We can also do OEM/ Private Labeling Port of Loading: Semarang, Indonesia Baby Diapers FLUFFY Tape (Velcro) Type. Available Variants: 1. FTS10 (S Size. 1 Box = 10 Bag x 30 Pcs) 2. FTS 20 (S Size. 1 Box = 20 Bag x 15 Pcs) 3. FTS 40 (S Size. 1 Box = 40 Bag x 6 Pcs) 4. FTM 9 (M Size. 1 Box = 9 Bag x 30 Pcs) 5. FTM 18 (M Size. 1 Box = 18 Bag x 15 Pcs) 6. FTM 36 (M Size. 1 Box = 36 Bag x 6 Pcs) 7. FTL 8 (L Size. 1 Box = 8 Bag x 30 Pcs) 8. FTL 32 (L Size. 1 Box = 32 Bag x 6 Pcs) 8. FTX 7 (XL Size. 1 Box = 7 Bag x 30 Pcs) 9. FTX 14 (XL Size. 1 Box = 14 Bag x 16 Pcs) Baby Diapers FLUFFY Pants Type. Available Variants: 1. FPS 20 (S Size. 1 Box = 20 Bag x 12 Pcs) 2. FPM 8 (M Size. 1 Box = 8 Bag x 24 Pcs) 3. FPM 18 (M Size. 1 Box = 18 Bag x 12 Pcs) 4. FPM 34 (M Size. 1 Box = 34 Bag x 6 Pcs) 5. FPL 7 (M Size. 1 Box = 7 Bag x 24 Pcs) 6. FPL 18 (L Size. 1 Box = 18 Bag x 12 Pcs) 7. FPL 30 (L Size. 1 Box = 30 Bag x 6 Pcs) 8. FPX 16 (L Size. 1 Box = 16 Bag x 12 Pcs) 9. FPX 26 (L Size. 1 Box = 26 Bag x 8 Pcs)

important Note: We can also do OEM/ Private Labeling Port of Loading: Semarang, Indonesia Baby Diapers Mamamia Tape (Velcro) Type. Available Variants: 1. MTS10 (S Size. 1 Box = 10 Bag x 24 Pcs) 2. MTS 20 (S Size. 1 Box = 20 Bag x 12 Pcs) 3. MTM 10 (M Size. 1 Box = 10 Bag x 24 Pcs) 4. MTM 20 (M Size. 1 Box = 20 Bag x 12 Pcs) 5. MTM 40 (M Size. 1 Box = 40 Bag x 6 Pcs) 6. MTL 10 (L Size. 1 Box = 10 Bag x 24 Pcs) 7. MTL 20 (S Size. 1 Box = 20 Bag x 12 Pcs) 8. MTL 36 (S Size. 1 Box = 36 Bag x 6 Pcs) 9. MTX 10 (XL Size. 1 Box = 10 Bag x 24 Pcs) 10. MTX 20 (XL Size. 1 Box = 20 Bag x 12 Pcs) Baby Diapers Mamamia Pants Type. Available Variants: 1. MPS20 (S Size. 1 Box = 20 Bag x 12 Pcs) 2. MPM9 (M Size. 1 Box = 9 Bag x 16 Pcs) 3. MPM 20 (M Size. 1 Box = 20 Bag x 12 Pcs) 4. MPM 34 (M Size. 1 Box = 34 Bag x 6 Pcs) 5. MPM 60 (M Size. 1 Box = 60 Bag x 4 Pcs) 6. MPL 8 (L Size. 1 Box = 8 Bag x 16 Pcs) 7. MPL 20 (L Size. 1 Box = 20 Bag x 12 Pcs) 8. MPL 30 (L Size. 1 Box = 30 Bag x 6 Pcs) 9. MPL 54 (L Size. 1 Box = 54 Bag x 4 Pcs) 10. MPX 18 (XL Size. 1 Box = 18 Bag x 12 Pcs) 11. MPX 26 (XL Size. 1 Box = 26 Bag x 8 Pcs)

2-Naphthol Basic information Chemical Properties Application Preparation Product Name: 2-Naphthol Synonyms: c.i.37500;c.i.azoiccouplingcomponent1;c.i.developer5;Developer A;Developer AMS;Developer BN;developera;developerams CAS: 135-19-3 MF: C10H8O MW: 144.17 EINECS: 205-182-7 Product Categories: Fluorescent;Naphthalene;pigments;alcohol;MICROCIDIN;Color Former & Related Compounds;Developer;Functional Materials;Intermediates;Aromatic Compounds;Alphabetical;Bioactive Small Molecules;Biochemicals and Reagents;Building Blocks;C9 to C20+;Cell Biology;Chemical Synthesis;Fluorescent Indicators and Probes;Fluorescent Probes;Labels;N;Organic Building Blocks;Oxygen Compounds;Particles and Stains;pH Sensitive Probes and Indicators;Phenols;Dyestuff Intermediates;Aromatics Mol File: 135-19-3.mol 2-Naphthol Chemical Properties Melting point 120-122 C(lit.) Boiling point 285-286 C(lit.) density 1,28 g/cm3 vapor density 4.97 (vs air) vapor pressure 10 mm Hg ( 145.5 C) refractive index 1.5762 (estimate) Fp 153 C storage temp. Refrigerator solubility methanol: soluble1g/10 mL, clear, colorless to light yellow pka 9.51(at 25C) form Powder, Crystals or Granules color White PH Range Non& uorescence (8.5) to blue & uorescence (9.5) Water Solubility 1 g/L (20 C) �»max 226nm, 265nm, 275nm, 286nm, 320nm, 331nm Merck 14,6384 BRN 742134 Stability: Stable. Combustible. Dust may form explosive mixture with air. Incompatible with strong oxidizing agents, phenol. Major Application Display device, semiconductors, photoimaging materials, inks, toner, chalk, security paper, molding materials, tin plating method, rubber, adhesive, leather, detergent, hair dyes, antimitotic drug, anticancer agent, antiinflammatory agent, treatment of acne vulgaris (pimples) and other dermal ailments (rashes, scratches, blemishes, hair loss), disorders InChIKey JWAZRIHNYRIHIV-UHFFFAOYSA-N CAS DataBase Reference 135-19-3(CAS DataBase Reference) NIST Chemistry Reference 2-Naphthalenol(135-19-3) EPA Substance Registry System 2-Naphthalenol (135-19-3) Safety Information Hazard Codes Xn,N Risk Statements 20/22-50 Safety Statements 24/25-61 RIDADR UN 3077 9/PG 3 WGK Germany 2 RTECS QL2975000 F 8 Autoignition Temperature 430 C TSCA Yes HazardClass 9 PackingGroup III HS Code 29071590 Hazardous Substances Data 135-19-3(Hazardous Substances Data) Toxicity LD50 orally in Rabbit: 1960 mg/kg LD50 dermal Rabbit > 10000 mg/kg 2-Naphthol Usage And Synthesis 2-Naphthol Preparation Products And Raw materials

Shubhlaxmi industries are one of the pioneer manufacturer and exporter of naturally selected and assorted best quality coriander seeds. We thrive to keep our standards high in terms of the product richness and quality. We maintain its basic aroma and flavor till it reaches you. The botanical name of coriander seeds is Coriandrum sativum L. It belongs to family Apiaceae. The plant has two types of seeds. One when dried is, used as dry spice. The other when ripe is yellowish brown in color and longitudinal shape. Coriander seeds are distinctly aromatic and they are used as one of the common Indian spices to enhance flavor to the dishes. Coriander seeds are usually used in whole form if they are roasted to make powder. They can be grounded to make powder than can be used in making Indian curry masala. It can be added to rice to enrich its fragrance. They can also be used to make chutneys and gravies. Coriander seeds are known to lower down diabetes. They are carminative. They are anti inflammatory and thus are used as medicine in arthritis. Specification HS Code : 09092190 Type : Machine Cleaned & Sortex Cleaned Variety : Eagle, Scooter, Parrot, Super Xo & Spits Flavour : Aromatic With A Penetrating Flavor Moisture : 9% Max Style : Dried Immatured Seeds : 1% Max Total Ash : 9.5% Max Acid Insoluble Ash : 1.75% Salmonella : Absent/25gms Origin : Gujarat,rajasthan,uttarpradesh Packing : 5/15/25/50 Kg Net Pp Bag/ Jute Bag/ Cartoon Quality Assurance : Sgs,geo-chem, Bureau Veritas Loading Capacity : 10mt In 20'fcl & 20mt In 40'fcl

Origin: Vietnam. Moisture: 10-12% max. Taste: crispy, lightly sweet. Shelf life: at least 24 months from production date (no air leak) No Co2, no SO2, no preservatives. Process: Air Drying, with 1-5% sugar. Quantity capacity: 50 tons/month. Min order quantity: 2,000 kg. Packaging: in 7 kg NW carton, 1x20'HQ = 6 mts, buyerâ??s brand available. Price: please contact for updated price. Payment & delivery: L/C at sight or T/T 30% in advance. Lead time: 2 weeks/ 1*20'FCL.

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Las 4NF- Lactose Substitute Non- Fat Solid is an Enzymatically Modified, Clean Label, Vegan, Gluten-Free, Plant-based and Non-GMO starch used as a special additive for improving texture of Paneer. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). APPLICATIONS 1. Milk is first heated (pasteurizing) to 85�°C and held for 12 minutes. 2. Add 2% to 20% of LAS 4NF based on the Protein Content of the Milk to the pasteurized milk and stir slowly to ensure full dissolving at 80C. 3. LAS 4NF itself contains coagulant. If necessary add coagulant as per the costumer requirement slowly to the milk by slow stirring, maintaining the temperature at 70�° C. 4. Keep Slow stirring for complete separation of solids and whey. (Indication: Whey will turn to light green color and small lumps of solids will settle down) 5. The whey water is filtered through a fine mesh of muslin cloth. The separated particles remain in muslin cloth and it is held in hoofer. 6. Apply pressure on the covered solid spread evenly on hoofer, with a flat lid in lay till water droplets stop. 7. Then the Paneer is pre-cooled in pure water at room temperature for 10 mins or till the external sides can be held in hand water for 10 mins , then dip in chilled water for 4 hours. DOSAGE Use 2 to 20% of LAS 4NF of total batch size, based on the protein content of the milk. For lower protein content in the milk higher LAS 4NF need to be used.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

We at GREENLAND FRESCO procure Peanuts in the most professional way and always ensure that fresh and healthy products are delivered to our clients. We keep pace with the latest technology and market requirements to ensure stability & sustainability towards fulfilling the clients demand. We have built a cost-effective and reliable supply chain to deliver Java & Bold varieties of Peanuts in one click. We maintain aflatoxin level & moisture content at minimal level. Peanuts are processed at processing plants to obtain the required specifications specified by our clients. Specifications of Bold / Java / Blanched Bold / Blanched Java Peanut kernels : - Type - Peanut kernels Peanuts counts per Ounce - 38/42, 40/50, 50/60, 60/70, 70/80 Origin - India Admixture - 1% max Oil content - 42% - 48% max Foreign Material - 0.50% max OR 1% max Moisture - 7% max OR 8% max Aflatoxin - Aflatoxin negative 5/10 PPB Gross Wt. per Bag - 10/15/25/50 Kgs Packaging Material - New Jute Bags Load Ability : One 20" FCL can load 19 MTS or 380 Bags of 50 Kgs New Jute Bags One 20" FCL can load 19 MTS or 760 Bags of 25 Kgs Vacuum Bags New vacuum pack inside and outer layer with PP woven bags 25 Kgs Gross Specifications of Peanuts in Shell Bold / Java : - Type - Peanuts in shell Bold : HPS- Ground nuts Peanuts bold shell - 18/22, 20/24, 22/26 Counts/Ounce Origin - India Moisture - 6-8% Max Admixture - 1% Max Imperfect - 5% Max Aflatoxin(B1+B2+G1+G2) - 5-10 ppb (as per clients specifications) Packing - In Strong Jute Bags of 30 Kgs Net/Gross Each One 20" FCL can load 12-14 MTS One 40" FCL can load 19-20 MTS Health Benefits 1. Peanuts have a strong nutritional Profile 2. Peanuts can reduce the risk of Heart disease 3. Peanuts are excellent source of plant based protein, fiber and many key vitamins and minerals. 4. Peanut consumption reduces the risk of weight loss and obesity 5. Peanut consumption reduces the risk of colorectal cancer

Ball clay, or plastic clay as it is also known, is an extremely rare mineral, only found at a handful of locations around the world. It is a kaolinitic clay that commonly consists of 20 - 80% kaolinite, 10 - 25% mica, 6 - 65% quartz as well as organic matter. Ball clay is formed from the weathering and transportation by water of parent rocks which are deposited in ancient river basins from where it is extracted. Applications: - Ball clays are prized for the production of traditional ceramics such as sanitaryware, tableware, wall and floor tiles as well as for technical ceramics and electrical porcelains. Ball Clay products are immensely used in the manufacturing of Ceramics, Sanitaryware, Vitrified Tiles, Glazes and Engobes ultramarine and in various other purposes. As per requirement Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. BRIGHTNESS: - 96+ AS PER REQUIREMENT Index Compound Result 1. Silica - (SiO2) 50 - 65 % 2. Alumina - (AI2O3) 20 - 35 % 3. Iron - (Fe2O3) 0.33 - 2 % 4. Titanium - (TiO2) 0.31 - 3 % 5. Potash - (K2O) 0.19 - 2 % 6. L Value 60 - 88 %

MOQ : 500 Kilogram Business Type : Manufacturer, Exporter, Supplier Product Details Type : Fresh Fruit Cultivation Type : Common, Organic Shelf Life : 3 Months Purity : 100% Feature : Excellent Quality Taste : Delicious Packaging Type : Boxes Benefits : Improves Eyesight, Lowers Risk Of Cancer Packaging Size : 1-10KG10-20kg, 20-30KG, 30-50KG Country of Origin : India Additional Information Payment Terms : L/C, D/P Preferred Buyer From Location : All Countries Except India In one 6-ounce serving of dragon fruit cubes, you'll get: Calories: 102 Fat: 0 grams Protein: 2 grams Carbohydrates: 22 grams Fiber: 5 grams Sugars: 13 grams

M. oleifera is a fast-growing, deciduous tree that can reach a height of 10 -12 m (32- 40 ft) and trunk diameter of 45 cm (1.5 ft). The bark has a whitish-grey colour and is surrounded by thick cork. Young shoots have purplish or greenish-white, hairy bark. The tree has an open crown of drooping, fragile branches and the leaves build up a feathery foliage of tripinnate leaves. The flowers are fragrant and hermaphroditic, surrounded by five unequal, thinly veined, yellowish-white petals. The flowers are about 1.0 - 1.5 cm (1/2) long and 2.0 cm (3/4) broad. They grow on slender, hairy stalks in spreading or drooping flower clusters which have a length of 10 -25 cm. Flowering begins within the first six months after planting. In seasonally cool regions, flowering only occurs once a year between April and June. In more constant seasonal temperatures and with constant rainfall, flowering can happen twice or even all year-round. The fruit is a hanging, three-sided brown capsule of 20 - 45 cm size which holds dark brown, globular seeds with a diameter around 1 cm. The seeds have three whitish papery wings and are dispersed by wind and water. In cultivation, it is often cut back annually to 1 - 2 m (3 - 6 ft) and allowed to regrow so the pods and leaves remain within arm' s reach.