FIELDS OF APPLICATION According to design solutions composite rebars ALB-REBAR shall be used in the following areas: Railway construction: Elements of railway sleepers for high-speed trains and underground railroads. Residential construction and civil engineering Construction foundations; Repair & reinforcement of bearing capacity in brick and reinforcement concrete structures. Highway construction: Reinforcement of roadbed Road, airfield & gray portlandcement slabs. Industrial engineering Reinforcement of concert tanks, storages of treatment facilities, sewage wellâ??s covers; Elements of chemical manufacturing facilities; Reinforcement of concrete floor; Water development facilities. Bridge building & reconstruction: Bridge deck slabs Bridge enclosures Footways Reinforcement of onshore facilities ADVANTAGES OF COMPOSITES Application of composite rebars ALB-REBAR increases constructionâ??s life time and time between repairs by means of: Excellent corrosion resistance in acid, alkali and other aggressive environment High tensile strength; 2 times higher compared to steel 1100-1300 MPa. Low weight; �¼ the weight of an equivalent size steel bar (savings on transportation). Durability No electrical conductivity Anti-magnetic Eco-friendliness and fire safet
D16-24mm length 1200-2600mm Rod ultimate load 80-160kn Pallet size:120x120x6 120x120x10 150x150x8 150x150x10 150x150x10
Fiberglass rebar Pulwell manufactures composite r-bars by combining the pultrusion process and an in-line winding & coating process for the outside sand surface. The frp composite rebar is made from high strength glass fibers along with an extremely durable vinyl ester resin. The glass fibers impart strength to the rod while the vinyl ester resin imparts excellent corrosion resistance properties in harsh chemical and alkaline environments. For improved stiffness and mechanical properties a carbon/vinyl ester product is available. Frp rebar significantly improves the longevity of civil engineering structures where corrosion is a major factor. Package in bundles
FRP Rebar is a new kind of composite material, which is glass fiber as reinforcement material, combines with epoxy (resin) and curing agent, then through pultrusion molding process. Fiberglass imparts the strength of the rod, while resin imparts excellent corrosion resistance to harsh chemical and alkaline environments. The products are widely used in construction, transportation industry, coal mine tunnel, parking structures,half coal roadway, slope support, subway tunnel, rock surface anchoring, seawall and dam etc. Main Features Corrosion Resistance: The base materials used by the bolt are durable materials, and they are molded through the composite process. The life span is up to 100 years. High Tensile Strength: The load is approximately double that of a steel bar with the same diameter; Light Weight: The weight is only 1/4 that of a steel bar with the same diameter.Therefore, the labor intensity is greatly reduced, and the transportation cost is reduced at the same time; Anti-static: It has no electrical conductivity, and no sparks will be produced when being cut. It is particularly suitable for high gas zones. The GFRP rockbolt is a fully threaded rodmade of glass fiber and reinforced resin with filling materials such as curingagent and flame retardant, and processed by pultrusion, winding and otherprocesses. The supporting tray nut is the GFRP rockbolt. It is mainly used forthe support of coal mine rock tunnels, semi-coal rock tunnels, coal walls,surrounding rock faces, slope anchoring and other underground projects.
Fiberglass reinforcement (GFRP) is made of linear strands of glass fibers, which are collected in the beam reinforced with periodic profile, impregnated with a thermosetting resin binder, then exposed to heat (polymerization) and cooled. It turns a solid rod of high strength three times the strength of steel by tensile test results, and less weight 9 times with equal diameters. Our GFPR rebar is made of epoxy resin and glass fiber direct roving (E-glass). We produce it in coils of 50m, 100m, 150m and 200m or in rods (from 0,5m and up to 12m).
Fiberglass reinforcement (GFRP) is made of linear strands of glass fibers, which are collected in the beam reinforced with periodic profile, impregnated with a thermosetting resin binder, then exposed to heat (polymerization) and cooled. It turns a solid rod of high strength three times the strength of steel by tensile test results, and less weight 9 times with equal diameters. Our GFPR rebar is made of epoxy resin and glass fiber direct roving (E-glass). We produce it in coils of 50m, 100m, 150m and 200m or in rods (from 0,5m and up to 12m).
(1)SBR glue can keep more than 50% after 28 days NaoH test. (2)Our fiberglass yarn is from Shandong; (3)Certificates to guarantee quality: Usually width/length is: 1X50M, and we can produce big roll: 1X1000M or other sizes as your requirement.
Glass fiber rebar or GFRP is a new kind of composite material which is used as reinforcement materials that combines with epoxy resin and curing agent then through pultrusion molding process. Products Feature: 1. High Corrosion Resistance:The base materials used by the bolt are durable materials, and they are molded through the composite process. The life span is up to 100 years. They can be used as permanent support materials; 2. High Tensile Strength:The load is approximately double that of a steel bar with the same diameter; 3. Low weight-The weight is only 1/4 that of a steel bar with the same diameter, therefore, the labor intensity is greatly reduced, and the transportation cost is reduced at the same time 5. Anti-static-It has no electrical conductivity, and no sparks will be produced when being cut, it's particularly suitable for high gas zones; 6. Non-flammable-It's non-flammable and has high thermal isolation; 7. Culpability-It avoids damages to cutter heads, and does not delay excavation 8. Save cost-Use this material as reinforcing bars for road and bridge, could reduce secondary repair cost. Material: 100% glass fiber and epoxy Surface: all thread Diameter: 3-40 mm Tensile strength: 780-1200Mpa Density: 1.9-2.1 g/cm3 E-Modulus: >45 gpa
Fishing boat, business boat, passenger boat, cabin boat, fiberglass boat, FRP boat, yacht, fish speed boat, leisure boat, rowing boat, power boat. Name : Specification Boat Materials : Fiberglass Boat size: 9.8m*2.81m*1.26m Max people : 11+1 Engine : outboard :115 x 2 Waterline : 0.45m above speed : 50km/h
Glass fiber mesh cloth alkali resistant and crack resistant plastering of internal and external walls on construction site
black fiberglass tissue can offer widest range of woven fabrics which are made of E-glass yarn. Our woven glass fabrics are manufacture with state of the art weaving technology and the best control over thickness, weight and strength.We can offers the materials engineer a wide choice of control fabric properties to satisfy design needs and objectives. Our extensive range of Fibreglass fabrics are globally recognised for its quality. black fiberglass tissue with fire retardant and alkali-free performance, is suitable as a surface lamination for fiberglass wool and rock wool thermal insulation.
Sodium Silicate is an inorganic chemical wherein its formulations vary depending on amount of Na2O and SiO2. This compound is well known as Water Glass in industries. We mainly supply following types of Sodium Silicate: 1) Sodium Silicate Lumps - Neutral Grade 2) Sodium Silicate Lumps - Alkaline Grade We maintain quality consistency in bulk supplies..
The basalt fiber roving of our company adopts the new tank kiln method and 2400 hole large leakage plate to form basalt roving products With a series of advantages such as high strength, large modulus, good temperature resistance, good chemical corrosion resistance and good electrical insulation, basalt is produced with homogenized basalt raw materials, with excellent performance, stable quality and small dispersion coefficient. Basalt fiber roving is a new material to replace glass fiber and carbon fiber
Fiberglass Reinforced Plastic grating is made by interlacing glass fibers and molded by resin casting. With its many rectangular and square spaces, it provides two-dimensional homogeneous mechanical characteristics. The typical size of the product is - 1220 x 3660 mm. However, it is available in different mesh sizes and thickness - Advantages - Easy to assemble - High Load-bearing capacity - Easy to install and maintain / repair - Durable in harshest environments - Suitable for ventilation and natural lighting
FRP composite rebars are made from reinforcing elements and polymer matrix. As reinforcing elements used the continuous high-strength fibers ( fiberglass, basalt or carbon) which combined in rod by polymer binding. The outer surface of the rebar has a continuous rhombic relief.
Fiberglass rebar.
Hello We are a manufacturer of fiberglass rebar in Ukraine (FRP rebar). We can supply different kind and different sizes.
constructions.
size upon request
Fiberglass rebar area of application Fittings made of composite materials are a product of new technologies, the technical characteristics of which make it possible to successfully use it as an alternative to traditional steel fittings in construction of: Foundation; Marine and port facilities; Reinforcement of concrete tanks; Repair and strengthening of bearing capacity of brick and reinforced concrete structures; Road slabs, airfield slabs; For the production of small architectural forms; For the road paving and decking of highway bridges; The implementation of the infrastructure elements in the chemical industries; Repair of damaged brick and reinforced concrete structures; Fittings are used for constructions based on gypsum binders; Construction of swimming pools and industrial pools; The application of fiberglass fittings in civil and industrial construction is caused by many variables: Low specific gravity; High corrosion resistance; Low thermal conductivity of composite materials; High strength, several times the strength of steel fittings; Is a dielectric; Durability; As known, the main drawback of traditional low-carbon steel fittings is a low index of corrosion resistance, which limits their use in the construction of marine facilities and constructions located in the zone of variable water level.
