Nano Technology Metal conditioner NASA approved. Not an oil Not an Additive 100% Synthetic 100% Eco friendly 500+ Worldwide known brands already in use
Today, carrying out its operations in the facilities located at Gebze Organized Industry Zone on a land covering 25.500 m², with a 40.000 tons/year capacity, exporting its high quality & performance products which are also certified by international authorities, to more than 40 countries. its high-quality products in 5 main categories, -Metal Working Oils, Industrial lubricants, Automotive lubricants, Greases and Marine lubricants- in 34 product groups with 1.000 different synthetic, semi-synthetic and mineral type of products to the industry and consumers worldwide. Please contact us for order detail
Oxidized Bitumen 90-10 is made by ongoing or Staggered Blowing Process. Heated Penetration bitumen under controlled environment is blown with air which controls oil content in bitumen while it oxidized. The different grades for suited applications produced are designated by two numbers to indicate the mid-points of their softening point and penetration ranges.
OXIDIZED BITUMEN 115/15 IS BASED ON PETROLEUM BITUMEN WHICH IS MADE BY BLOWING BITUMEN 60/70 BY VERY HOT AIR.
Maximum AC Output (kVA) : 1.2 Prime Power / kVA (kW): 0.9 Rated Current (A) : 4 DC Output : 0 Output Voltage (Volt): 230 Frequency (Hz): 50 Power Factor ( Cos +): 1 Automatic Voltage Regulator : + Large Capacity Air Cleaner : 0 Large Capacity Muffler : + Oil Alert : 0 Voltmeter : + AC Circuit Breaker : + DC Circuit Breaker : 0 Fuel meter : 0 Battery : 0 4 wheel dolly kit : 0 Dimensions LxWxH (mm) : 410x305x350 Dry Weight (Kg): 23 Easy lifting and moving (Optional) Metal parts are coated with electrostatic polyester coated, powder painted Acustic insulation with rot-proof, moisture repellent and non flammable material.
What is Base Oil? Base oil, also known as base stock, is a type of oil that is used as a primary component in the production of lubricants, including engine oils, gear oils, hydraulic oils, and others. Base oil typically makes up a large portion of the final lubricant product, and its quality and properties have a significant impact on the overall performance of the finished lubricant. Base oil can be derived from various sources, including crude oil, natural gas, and synthetic materials. It undergoes a refining process to remove impurities and contaminants, which can affect the lubricant's performance and lifespan. The quality of base oil is typically classified according to its viscosity, which is a measure of its resistance to flow at a particular temperature. Base oils are classified into different groups based on their viscosity index, chemical composition, and other characteristics.
For Lubrication Oil which is considered as a basis and after adding additives to the final lubricant called based oil . In terms of volume of lubricant it is one of the most important components in the lubricant base oil formulation, on average, 95% up. Some groups, such as hydraulic and compressor lubricant, chemical additives and only 1% base oil makes up 99% combined. Other lubricants like metal working fluids, lubricants and gear oils contain additives may be up to 30%. Since crude oil containing different combinations such as paraffinic hydrocarbons, naphthenic and aromatic sulfur compounds are also, we can also make up of these compounds. It composition comprising a major effect on the properties of spent oils, paraffinic compounds, naphthenic and aromatic. The normal packing is Drum and Flexi. Also in large quantity we can supply as bulk.
Paraffin wax, colourless or white, somewhat translucent, hard wax consisting of a mixture of solid straight-chain hydrocarbons ranging in melting point from about 48 to 66 C (120 to 150 F). Paraffin wax is obtained from petroleum by dewaxing light lubricating oil stocks.
The Ozdekan EXpansion Joints are waterproof expansion joints that allow absorption of the deck movements. These joints are manufactured with rubber elements and restrained to the structure with proper anchor bolts. The reinforcing metal profiles made of steel are completely inserted and vulcanized to the rubber. This process is a total guarantee against corrosion and allows a longer life to the product. The rubber compound, too, has been intentionally formulated to resist the oil, grease, petrol, salt and sand, without besides, suffering premature ageing phenomena due to sun rays, salt and snow. All the joints follow the deformations and movements of the structure (the movement can exist with every skew angle from 0° to 90°) by shear deformation of the rubber elements. Anchor bolts, made of steel and protected with anticorrosion treatments, absorb the elastic reactions and all the other kind of mechanical solicitations. The joints are also able to compensate height difference or vertical movements. This characteristic is very important in all the cases where load and movement conditions can cause relative vertical movements. The joint series is manufactured by Ozdekan since 2006. Main advantages: Simple and linear design with few elements Low height of the profile Total impermeable Easy assembling eitheron concrete structure Suitable for the replacement of existing joint Easy and quick to be replaced Good resistance to vehicles sliding Vertical movements absorption The joints are supplied in variable length elements depending to the joint type. A joint line consists in fact of many units joined together with a groove-and-tongue junction welded with special glue. The joint fixing is obtained by chemical anchors; the nuts are locked using a dynamometric key so that permanent compression strength is given to the joint. Stainless steel anchors may be provided on request. In that way the horizontal forces, due to breaking of vehicles and to the reaction that rubber opposes to the joint deformations (shrinkage, creep, thermal variations etc.), are transmitted by friction between the rubber and the concrete. The joints can be assembled on a metallic infrastructure. The joints of bigger movements with four upper grooves are manufactured in order to prevent the lifting of the elements during the contraction. These devices guarantee the adhesion of the elements to the structure and the noiseless of the traffic.
Caustic Soda Flakes - Sodium Hydroxide Production of organic chemicals Production of cosmetic products such as soap or peeling masks Production of all kinds of industrial detergents according to the oil-dissolving feature of sodium hydroxide Raw material in the production of all kinds of pigments and dyes in the paint industry Bleaching of fabrics used in textiles All kinds of ceramic and glass production Defined processes in the food industry Fuel cell production PH adjustment factor in water purification and reducing water hardness Removal of acid in compounds used in the petrochemical industry and oil and gas refineries Of course, it would be fair to say that its main applications are aluminum production for the steel and metallurgical industries, pulp production, and bleaching of the paper and chemical industries.
Box Culvert Machine; It produces Concrete Culverts between 800 - 800mm and3000 - 3000mm in minimum 1000mm and maximum 2000mm lengths. Production is made by connecting a single mold in all sizes. Vibration system of the machine is with liquid oil closed circulation system. Automatic lubrication system is activated with machine operation. SKF or FAG bearings resistant to high cycles and heat are used in the vibrator.
KMS 800 Triple System Concrete Pipe Machine; It produces Concrete Pipes between 150mm and 800mm in minimum 1000mm and maximum 2000mm lengths in accordance with Seller Bank TSE 821 specification. Three molds for 150mm and 200mm Concrete Pipes, two molds for 300mm Concrete Pipes and one mold for other diameters can be connected at the same time. Molds and Pallets with Integrated Gasket or Drop Section Gasket are produced in line with the demands from �?150mm to 800mm. Vibration system of the machine is with liquid oil closed circulation system. Automatic lubrication system is activated with machine operation. SKF or FAG bearings resistant to high cycles and heat are used in the vibrator. â?¢ Pallets; It is produced on CNC lathes according to its dimensions and by pressing method. Manufactured Concrete Pipes are transported by forklift and shipped to the Drying area. Triple System Concrete Pipe Machine has been designed to produce concrete pipes in the fastest and fastest way.
KMS 1400 New Generation Concrete Pipe Machine; It produces Concrete Pipes from 300mm to 1400mm in line with the demands of our customers, from minimum 1000mm to maximum 2500mm in length in accordance with Iller Bank TSE 821 specification. It is manufactured in a way to make double or triple production according to customer demands. Three molds for300mm Concrete Pipe, two molds for 400, 500, 600mm Concrete Pipes and one mold for other diameters can be connected at the same time. â?¢ Molds and Pallets with Integrated Gasket or Drop Section Gasket are produced in line with the demands from �?300mm to �?1400mm. â?¢ It provides the possibility of mass production from �?300mm to �?1400mm without crane, it produces 2 times more than the system with crane. Vibration system of the machine is with liquid oil closed circulation system. Automatic lubrication system is activated with machine operation. SKF or FAG bearings resistant to high cycles and heat are used in the vibrator. Pallets; It is produced on CNC lathes according to its dimensions and by pressing method. Manufactured Concrete Pipes are transported to the Drying area by Forklift.
