Addition cure silicon rubber for artificial stone products pplications: It mainly use for making molds for resin, stone, gypsum and cement product with medium size. Addition cure silicon rubber for artificial stone products Typical Datasheet : Item No Color Hardness (A°) Viscosity (CS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2) Elongation-break(%) Mixing Ratio of silicone and catalyst Application(most for resin, stone, gypsum and cement product to make moulds) HY-E635 Translucent 35±2 8000±2000 =60 =13 =400 1:1 Addition cure silicon rubber for artificial stone products Points of attention: 1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse. 3,Addition cure silicone affect by temperature greatly when cured under room temperature. 4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. It’s fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it’s easy to make the catalyst to be poisoning. 5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa 6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it’s 1 : 1 or 10 : 1.
Addition cure silicone can be used for cake, candy food grade products mold making, addition cure silicone features low shrinkage.(features for low viscotity , good operation. Excellent performance. 25kg/drum and 200kg/drum
400 1:1 Most suitable for medium sized product Addition cure silicon rubber for artificial stone products advantages: Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller Addition cure silicon rubber for artificial stone products points of attention: 1, prone to poisoning, can not mix with condensation, ionic compounds containing n, s-, p, organic matter and of sn, as, hg, ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2, comparing with condensation cure silicone, addition cure silicone's adhesive properties to be worse. 3, addition cure silicone affect by temperature greatly when cured under room temperature. 4, addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. Its fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily, its easy to make the catalyst to be poisoning. 5, addition cure silicone rubebr has two-component, the component a and component b, please pay attention to clean the component a containers before using for the component b, and vice versa 6, in order to avoid the hardness change, we should mix the component a and component b according to its mixing ratio strictly, no atter its 1 : 1 or 10 : 1. 25kg/drum or 200kg/drum
Addition cure silicon rubber for artificial stone products Addition cure silicon rubber for artificial stone products pplications: It mainly use for making molds for resin, stone, gypsum and cement product with medium size. Addition cure silicon rubber for artificial stone products Typical Datasheet : Item NoColor Hardness (A-Viscosity (CS)Tensile-strength( kgf /cm2 )Tear-strength (kgf /cm2)Elongation-break(%)Mixing Ratio of silicone and catalyst,Application(most for resin, stone, gypsum and cement product to make moulds) HY-E635 Translucent 35,8000,2000;Y60,Y13,Y400 1:1Most suitable for medium sized product Addition cure silicon rubber for artificial stone products Advantages: Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller Addition cure silicon rubber for artificial stone products Points of attention: 1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse. 3,Addition cure silicone affect by temperature greatly when cured under room temperature. 4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. It fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it&easy to make the catalyst to be poisoning. 5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa 6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it 1 : 1 or 10 : 1. Addition cure silicon rubber for artificial stone products Package and storage : 1. 20kg or 200kg /drum. 2.It is a kind of non-dangerous goods, and it should be stored at a cool and dry place, please keep it from sun and rain. 1kg/drum 5kg/drum 20kg/drum 25kg/drum 200kg/drum
1.Description of addition cure liquid silicone rubber G-830 silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fastly by heating, Itâ??s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible. 2.Characteristics of addition cure liquid silicone rubber (1).An exceptional fluidity and good operability (2).Good tensile strength and tear strength (3).Food grade silicone rubber (4).high temperature resistance (5).good flexibility (6).No smell ,non-toxic (7).long shelf-time &lifetime (8).Lower shrinkage 3.Application of addition cure liquid silicone rubber G-830 silicone rubber is flexbile silicone rubber ,it has a higher temprature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing . Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
Features: 1. Excellent tear & tensil strength 2. No shrinkage 3. Food grade and enviromental silicone Ent, the component a and component b, please pay attention to clean the component a containers before using for the component b, and vice versa 6, in order to avoid the hardness change, we should mix the component a and component b according to its mixing ratio strictly, 25kg/drum and 200kg/drum
Addition cure Electronic Potting Silicone Rubber 1. Product Feature of Addition cure Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials. 2. Typical Application of Addition cure Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Addition cure Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. 4.Notes of Addition cure Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance. PACKAGE 40Kg/pail as a set (Part A 20Kg + Part B 20Kg) SHELF LIFE AND TRANSPORTATION 1. Twelve(12) months when stored at 24C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals. 3. Storage beyond the expired date doesnot necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons. -
Product Description Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials. Warm Tips for for PCB Electronic Potting Silicone 1. Sealing pakage for storage. The mixture should be used up at once to avoid wasting. 2. Silicone belongs to non-dangerous goods, but keep away form mouth and eyes. 3. When it gets stratified after a period of storage, Please mix HY-210# evenly before using, it does not affect the performance. Package for for PCB Electronic Potting Silicone Regular Package:20kgs/drum 200kgs/drum Small Package:1kg/tin 5kgs/tin Technical Guidelines 1. Pls put part A and B in separate container and stir evenly before mixing the two parts together. 2. Mixing Ratio part A:part B is 10:1 3. Bubble release if necessary, deaeration the mixture under 0.08 MPa for 3 minutes. 4. HY-215# is cured at roon temperature, so pls put it under room temperature after pouring. It comes to next process when basically cured, and it takes about 24 hours for completely cured.
OTT J820 is a food grade silicone suitable for making baking molds and trays, ice trays, casting butter, chocolate and other applications used to produce food. OTT offers the convenience of a 1A:1B by volume mix ratio and a fast 6 hour cure time. ; Materials you can cast into cake, chocolate,cookie molds ; A: Cultural relic duplication, architectural decoration, statues; B: Polyester Resin crafts C: Lighting ornaments, soap, candles molding D: Plaster, Gypsum, Cement, Concrete decorations F: Model design, product exploitation, etc. ; Datesheet for food grade silicone rubber ; Model,Mixing ;RatioColor,Hardness (shoreA)Viscosity ;(mPa.s)Working Time,Curing Time,Tear-Strength (kN/m)Tensile- Strength (Mpa),Elogation(%)Shrinkage (%) J820,1:1,Translucent,20, 2,6000 ,2000,20-40mins,3-5h ;Y20;Y5.0;Y450 ;¡§10.1 J825,1:1,Translucent,25, 2,7000 ;¡§¡è2000,20-40mins,3-5h;Y18 , Y6.0;Y450 Features of our food grade silicone rubber 1.) Never oily ; 2.)500~2000;duplication times 3.) Resistance to burn,acid,alkali and aging 4.) good tensile and high tear strength 5.) No viscosity 6.) Low shrinkage 1kg/tin; 5kg/tin; 20kg/drum; 25kg/drum; 200kg/drum
1.Description of liquid silicone rubber C830 Silicone rubber is condensation cure silicone rubber for mold making. The silicone rubber will be cured under room temperature, It’s two-components, the mixing ratio is 100:2 . Part A is a flowable liquid silicone , part B is the catalyst. It has an exceptional fluidity and good operability. C-830 tin cure mold silicone has a good property , it is suitable for various mold making . 2.Characteristics of liquid silicone rubber *An exceptional fluidity and good operability, easy to demold *Good tensile strength and tear strength *lower shrinkage *non-deformation ,non-oily *good flexibility *eco-friendly *long shelf-time &lifetime 3.Application of liquid silicone rubber stone mold ,concrete mold , cement casting mold polyurethane casting mold , GRC casting mold , fiberglass cating mold statue mold , sculpture mold , resin craft mold ,artificial wooden mold gypsum mold , plaster mold ,bronze casting mold candle mold ,soap mold, shoe mold , tyre mold ,etc ..... C830 Silicone rubber is mainly suitable middle sized product and big size with simple pattern. Package: 1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum based on vacuum packing. Shelf life and transportation 1. Twelve(12) months when stored at 25C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals.
1. Description of food grade liquid silicone rubber for making mould Addition-curing, Food grade, Translucent, Two-component mold making silicone. 2. Characteristics of food grade liquid silicone rubber for making mould Acceptable for food contact Outstanding release properties Low viscosity Easy mixing and degassing High flowability Odorless and Nontoxic Enhanced durability 3. Application of food grade liquid silicone rubber for making mould Food Grade Related Applications Cake mold Chocolate moldmaking Candy moldmaking Baking moldmaking Ice trays molding Casting butters Casting for Kitchen products 5. Using instructions of food grade liquid silicone rubber for making mould Step 1: Prepare and clean the prototype. You must make sure your original molds perfect, fix the original mold on a board, then using some assistant material (like cardboard) to make a frame for to surround the prototype. The frame is no need, if we make the mold by brushing way. Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone : catalyst= 100:2), mix the silicone rubber and catalyst evenly. Notes: rtv silicone rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicone rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finishes molds will have a short life. All of these will cause a waste of silicone rubber. Step 3: Vacuum pumping. After mixed the silicone evenly, it is better to release the bubble by vacuum pumping. Step 4: Pouring cast or brushing cast. After released the bubble, we can pour/brush the silicone rubber on the prototype. Notes: Please finishes all the steps within the operation time. If not, it will cause cross linking reaction, and no more further steps will be available. So, we have to pay attention to the pot life and curing time. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1. Description of rtv 2 liquid silicone rubber for frame gypsum molds C830 silicone rubber is condensation cure silicone rubber (tin cure silicone rubber) for mold making. The silicone rubber will be cured under room temperature. It's two components, the mixing ratio is 100:2. Part A is a flowable liquid silicone, part B is the catalyst. It has an exceptional fluidity and good operability. 2. Characteristics of rtv 2 liquid silicone rubber for frame gypsum molds * An exceptional fluidity and good operability, easy to demold * Good tensile strength and tear strength * Suitable hardness * Copy detailed pattern * Good flexibility * Eco-friendly * Long shelf-time &lifetime 3. Application of rtv 2 liquid silicone rubber for frame gypsum mold C830 liquid silicone rubber is perfect molding material, it is suitable to make mold for concrete casting, artificial stone, brick, cement casting, gypsum decorations, plastic product, resin craft, polyester, polyurethane, bronze casting, statues, jewelry, wax, crystal, tire mold, shoe mold, clay casting, ceramic casting. etc. C830 liquid silicone rubber is mainly suitable for small or middle sized products with delicate pattern by pouring and brushing operation. Package 1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum. Shelf life and transportation 1. Twelve(12) months when stored at 25C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals.
1.Description of Platinum liquid silicone rubber for mold making G830 Silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fast by heating, It’s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible. 2.Characteristics of Platinum liquid silicone rubber for mold making *An exceptional fluidity and good operability *Good tensile strength and tear strength *Food grade silicone rubber *high temperature resistance *good flexibility *No smell ,non-toxic *long shelf-time &lifetime *Lower shrinkage 3.Application of Platinum liquid silicone rubber for mold making G830 silicone rubber is flexible silicone rubber ,it has a higher temperature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing . 4.Datesheet of Platinum liquid silicone rubber for mold making Item No. Appearance Hardness (shore A°) Viscosity (CPS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25? ) Curing time( 25 ?) shrinkage G830 translucent 30±2 7000±1000 =55 =24 =450 1:1 20-30 mins 2~3 h =0.1% Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1.Description of life casting rtv-2 silicone rubber for prosthetic hands RT-810 silicone rubber is platinum cure silicone rubber with medical grade , it belong to be life casting silicone rubber. The silicone rubber will be cured under room temperature and can be cured under room temperature and can be fastly by heating. It's two components liquid silicone rubber, the mixing ratio is 1:1. It has an exceptional fluidity and good operability. Especially, the platinum cure silicone rubber has a lower shrinkage, higher temperature resistance G810 is extremely soft as a real feeling as humman skin 2.Characteristics of life casting rtv-2 silicone rubber for prosthetic hands *An exceptional fluidity and good operability *Good tensile strength and tear strength *Food grade silicone rubber *high temperature resistance *good flexibility *No smell ,non-toxic *long shelf-time &lifetime *Lower shrinkage 3.Datesheet of life casting rtv-2 silicone rubber for prosthetic hands Item No. Hardness (A°) Viscosity (CS) Tensile-strength ( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25 ? ) Curing time ( 25 ?) shrink-age RT-810 10 5000 40±5 10±2 450±50 1:1 20-30 mins 2~3 h =0.1% Notice of life casting silicone for prosthetic limbs RT-810 life casting silicone rubber is platinum cure silicone , which is very easy to cause cure inhibition , so please do remember thoroughly clean the model and tool before operation . Besides , please avoid the condensation silicone rubber (100:2) contact or mix with the following material , otherwise the silicone won’t be cured : 1. Liquid condensation silicone ( condensation silicone not completely cured or organic tin compounds ) 2. Sulphur, sulfide and sulfur rubber materials. 3. Amine compounds as well as contains the amine materials. 4. Pewter solder flux. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1. Description YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour. 2. Features *high chemical resistance to the aggressive components of some types of resin *High resistance to laceration (this characteristic guarantees high resistance to wear and tear) *High level of accuracy in reproducing very small particulars *High dimensional stability over time and non-deformability *Considerable resistance to high temperatures and to ageing *Excellent non-stick effect *Soft, stretchy, high tear resistance, *Will not shrink in service
Molding silicone rubber, addition cure liquid silicone, pad printing silicone rubber, injection silicone rubber, electronic potting silicone rubbe 25kg/drum and 200kg/drum
Description of platinum curing mould making liquid silicone rubber Addition cure silicone is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 1:1 or 10:1. It can cure at room temperature as well as under heat. It's a kind of food grade silicone and mainly used for mold making. Application of platinum curing mould making liquid silicone rubber Silicone rubber is mainly used for making molds of tire, concrete stone, grc, polyurethane products; wax, candle decoration; rapid prototyping and tyre molds; chocolate, candy and similar products.
High transparent addition cure silicone for Jewelry mold making is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 10:1. It can be cures at room temperature as well as under heat. It's a kind of food grade silicone ,And mainly used for jewelry mold making. High transparent addition cure silicone for Jewelry mold making is pourable, addition-curing, two-component silicone rubber that vulcanizes at room temperature or by heating. Non-toxic, odorless.Resistance high temperature is 250, shrinkage rate lower than 0.1%. It is great to make molds either with simple or intricate patterns,like artificial jewelry, resin Jewelry , artificial necklace, artificial bracelet etc. silicone molds serve very good performance in reproduction process with every fine detail on designing models.
Liquid silicone rubber, RTV-2 silicone rubber, condensation cure silicone rubber, addition cure silicone rubber, food grade silicone rubber.Technical support, new products developing
We are exporter of Ferro Silicon. FerroChrome is a kind of Ferro alloy which is formed by Ferro and Chrome,it is an important alloy addition in steel making. Ferrochrome (Fe Cr) is an alloy of chromium and containing between 50% and 70% chromium.
