Addition cure silicon rubber for artificial stone products advantages:
Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller
Addition cure silicon rubber for artificial stone products points of attention:
1, prone to poisoning, can not mix with condensation, ionic compounds containing n, s-, p, organic matter and of sn, as, hg, ph., easy molding plastic poisoning, resulting in the phenomenon of not curing.
2, comparing with condensation cure silicone, addition cure silicone's adhesive properties to be worse.
3, addition cure silicone affect by temperature greatly when cured under room temperature.
4, addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning.
Its fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily, its easy to make the catalyst to be poisoning.
5, addition cure silicone rubebr has two-component, the component a and component b, please pay attention to clean the component a containers before using for the component b, and vice versa
6, in order to avoid the hardness change, we should mix the component a and component b according to its mixing ratio strictly, no atter its 1 : 1 or 10 : 1.
Addition cure silicon rubber for artificial stone products
Addition cure silicon rubber for artificial stone products pplications:
It mainly use for making molds for resin, stone, gypsum and cement product with medium size.
Addition cure silicon rubber for artificial stone products Typical Datasheet :
Item NoColor Hardness (A-Viscosity (CS)Tensile-strength( kgf /cm2 )Tear-strength (kgf /cm2)Elongation-break(%)Mixing Ratio of silicone and catalyst,Application(most for resin, stone, gypsum and cement product to make moulds)
HY-E635 Translucent 35,8000,2000;Y60,Y13,Y400 1:1Most suitable for medium sized product
Addition cure silicon rubber for artificial stone products Advantages:
Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller
Addition cure silicon rubber for artificial stone products Points of attention:
1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing.
2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse.
3,Addition cure silicone affect by temperature greatly when cured under room temperature.
4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning.
It fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it&easy to make the catalyst to be poisoning.
5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa
6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it 1 : 1 or 10 : 1.
Addition cure silicon rubber for artificial stone products Package and storage :
1. 20kg or 200kg /drum.
2.It is a kind of non-dangerous goods, and it should be stored at a cool and dry place, please keep it from sun and rain.
Features:
1. Excellent tear & tensil strength
2. No shrinkage
3. Food grade and enviromental silicone
Ent, the component a and component b, please pay attention to clean the component a containers before using for the component b, and vice versa
6, in order to avoid the hardness change, we should mix the component a and component b according to its mixing ratio strictly,
Addition cure silicon rubber for artificial stone products pplications:
It mainly use for making molds for resin, stone, gypsum and cement product with medium size.
Addition cure silicon rubber for artificial stone products Typical Datasheet :
Item No Color Hardness (A°) Viscosity (CS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2) Elongation-break(%) Mixing Ratio of silicone and catalyst Application(most for resin, stone, gypsum and cement product to make moulds)
HY-E635 Translucent 35±2 8000±2000 =60 =13 =400 1:1
Addition cure silicon rubber for artificial stone products Points of attention:
1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing.
2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse.
3,Addition cure silicone affect by temperature greatly when cured under room temperature.
4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning.
It’s fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it’s easy to make the catalyst to be poisoning.
5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa
6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it’s 1 : 1 or 10 : 1.
Addition cure silicone can be used for cake, candy food grade products mold making, addition cure silicone features low shrinkage.(features for low viscotity , good operation. Excellent performance.
25kg/drum and 200kg/drum
8131 Addition Cure Silicon Rubber For Artificial Suppliers
Short on time? Let Addition Cure Silicon Rubber For Artificial sellers contact you.
Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags.
Ferro Silicon Ferro Silicon has a melting point of 1200�¯�¿�½?�?�°C to 1250�¯�¿�½?�?�°C with a boiling point of 2355�¯�¿�½?�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
FerroChrome is a kind of Ferro alloy which is formed by Ferro and Chrome,it is an important alloy addition in steel making. Ferrochrome (Fe Cr) is an alloy of chromium and containing between 50% and 70% chromium.
Silicone rubber surfactant (Organic silicone surface additive) Application:
It can be used as a spray modifier, foliar absorption aids, activation agent, widely used herbicide, liquid nutrients, growth regulators, insecticides, fungicides, which do not decompose the original pesticide, can greatly reduce the surface tension of the solution, reducing the contact between the droplet and the leaf angle, surface enhanced the liquid in the plant or pest surface wetting, adhesion, and a spreader, thereby improving efficacy.
Silicone surfactant ZINCA-2000 is lower phytotoxicity and environmental hazards than the normal fatty amines, ethoxylated alcohol surfactant, and greatly reduce human and environmental impact.
1.Description of addition cure liquid silicone rubber
G-830 silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fastly by heating, Itâ??s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible.
2.Characteristics of addition cure liquid silicone rubber
(1).An exceptional fluidity and good operability
(2).Good tensile strength and tear strength
(3).Food grade silicone rubber
(4).high temperature resistance
(5).good flexibility
(6).No smell ,non-toxic
(7).long shelf-time &lifetime
(8).Lower shrinkage
3.Application of addition cure liquid silicone rubber
G-830 silicone rubber is flexbile silicone rubber ,it has a higher temprature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing .
Packaging & Shipping
Packing:
20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B
25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B
200KG/drum packing for part A +200KG/drum packing for part B
1. Product Feature of Addition cure Electronic Potting Silicone Rubber
Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials.
2. Typical Application of Addition cure Electronic Potting Silicone Rubber
HY-9055 electronic potting silicone rubber could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
3. Technical Guidelines of of Addition cure Electronic Potting Silicone Rubber
a, Pls put part A and part B in separate container and stir evenly before mixing the two part together.
b, Mixing Ratio: part A: part B = 1:1
c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4.Notes of Addition cure Electronic Potting Silicone Rubber
a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas.
Organotin compound or Condensation silicone with organotin
Sulphur, sulfide and sulfur rubber materials.
Amine compounds as well as contains the amine materials.
Pewters solder flux
b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste.
c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes.
d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance.
PACKAGE
40Kg/pail as a set (Part A 20Kg + Part B 20Kg)
SHELF LIFE AND TRANSPORTATION
1. Twelve(12) months when stored at 24C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
3. Storage beyond the expired date doesnot necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
1. carbon black
2. rubber crumb
3. precipitated silica
4. silica quartz ore purity: 98% available, silica quartz powder/purity: 99.9% available, silica lumps purity: 99% available
5. calcium chloride powder 74% cacl2 92% cacl2 94%
6. magnesium chloride flake
7. sodium meta bisulphite (food grade 94 96%)
8. red onion as per your required size.
9. sodium acetate anhydrous 99% sodium acetate trihydrate crystal 99%
10.pet preform & fiber, bottle, flakes,
11.bopp tapes
12. capsicum or bell pepper, ready to eat foods, ready green paste like ginger, garlic paste.We also do logistic work for cif and we have 3rd party facilities like sgs on client chargeable base.
Ferrosilicon� is an alloy of iron and silicon that is made by reducing silica in the presence of iron, and which plays an essential role in steelmaking.
Silicon iron, also known as ferrosilicon, is a ferroalloy composed of iron and silicon, with a silicon content ranging from 15% to 90%. It is commonly used as a deoxidizer in steelmaking and as a reducing agent in ferroalloy production and the chemical industry. In the steelmaking industry, approximately 3-5 kg of 75% ferrosilicon is consumed to produce one ton of steel. Ferrosilicon can also be used as an alloying element additive, which is widely used in low alloy structural steel, spring steel, bearing steel, heat-resistant steel, and electrical silicon steel.
Ferrosilicon is also used in the production of cast iron, as it helps to control the initial content of silicon in the melt, which is important for the microstructure and properties of the final product. Ferrosilicon cast magnesium is an alloy that contains magnesium and is used as a nodulizer in the production of ductile iron. It has a big mechanical strength, and the effect of deoxidization and desulfurization is strong. Modifiers are added to molten metal to change its properties, and ferrosilicon is one of the most commonly used modifiers in the production of cast iron. The material forming the base Ferrosilicon analysis ferrosilico cast magnesium and modifiers.
The role of Ferrosilicon in Steelmaking:
In steelmaking, Ferrosilicon is used for:
Black Grass Jelly is a material with many uses. From stem powder and dried leaves are used to cook jelly jelly as a refreshing drink. in addition, starling stem powder is used as a processed food. In some countries such as Taiwan and Indonesia, it is thought that the starling tree leaf powder has diuretic effect or cures a number of diseases such as the common cold, high blood pressure, muscle aches and joints, diabetes, Acute hepatitis. Grass Jelly is also used to process industrial food.
Black Grass Jelly is a material with many uses. From stem powder and dried leaves are used to cook jelly jelly as a refreshing drink. in addition, starling stem powder is used as a processed food. In some countries such as Taiwan and Indonesia, it is thought that the starling tree leaf powder has diuretic effect or cures a number of diseases such as the common cold, high blood pressure, muscle aches and joints, diabetes, Acute hepatitis. Grass Jelly is also used to process industrial food.
Grass Jelly is a material with many uses. From stem powder and dried leaves are used to cook jelly jelly as a refreshing drink. in addition, starling stem powder is used as a processed food. In some countries such as Taiwan and Indonesia, it is thought that the starling tree leaf powder has diuretic effect or cures a number of diseases such as the common cold, high blood pressure, muscle aches and joints, diabetes, Acute hepatitis. Grass Jelly is also used to process industrial food.
Specifications:
English name: Mesona Chinensis Benth
Taste: Sweet, light and cool
Moisture: 12% max
Impurities: 2% max
Shelf life: 18 months
Process: Air Dry and Sundry
Form: Whole Leafs and Sticks
Applications:
Chlorine manufacturing
In petrochemical manufacturing
Rubber manufacturing
Caustic Soda manufacturing
In animal feed
In curing of hides
Soap and detergent manufacturing
As water softeners
In highway or road deicing
In textile industries
In paper and pulp industries
In drilling
Packaging:
35 kg per bag
50 kg per bag
1 ton jumbo bag
1.5 tons jumbo bag
2 tons jumbo bag
Pipe fittings are the general names of parts and components that play the role of connection, control, direction change, diversion, sealing and support in the pipeline system. Steel fittings are pressure fittings. According to the different processing technology, it is divided into four categories, namely, butt welding pipe fittings (divided into weld and no weld), socket welding and threaded pipe fittings, flange pipe fittings.
According to the application:
1. pipe fittings for connecting pipes are: flanges, live joints, pipe hoops, clamps, clamps, throat hoops, etc.
2. changing the direction of the pipe: bends, bends.
3. pipe fittings changing pipe diameter: variable diameter (different diameter pipe), different diameter elbow, branch pipe table, reinforcing pipe.
4. pipe fittings with additional piping branches: three links, four links.
5. pipe fittings for pipe sealing: gasket, raw material belt, thread, flange blind plate, pipe plug, blind plate, head, welding plug.
6. pipe fittings for pipe fixing: clasp, hook, ring, bracket, bracket, pipe clamp, etc.
According to the connection :1, welded pipe fittings 2, threaded pipe fittings 3, clamping pipe fittings 4, clamping pipe fittings 5, socket pipe fittings 6, rubber ring connection pipe fittings
According to the material divided into 1, cast steel pipe fittings 2, forged steel pipe fittings 3, alloy pipe fittings 4, stainless steel pipe fittings.
Pipe fittings are widely used in municipal, petrochemical, west-to-east gas transmission, ships and nuclear power.
Product Features
Appearance : White Or Light Yellow Crystal Powder
Odour: Sulfur Dioxide
Taste : Salty
Melting Poing : 150
Specific Density1.48
Ph : 4.0-4.6
Solubility : Soluble In Water ,insoluble In Alcohol
Application:
1. For industry
Mordant of printing and dyeing; Dechlorinate of textile after bleaching;
Sulphonated agent and reducer of chemical industry and pharmacy;
Bleach of paper pulp, bamboo and timber bleach of stapk; Treatment agent of waste water; Rubber solidifying agent ;Perfume industry is served as hydrocarbon perfume aldehyde ;
The hide profession employ to do to molt dose and pliable dose and wearproof dose ,The sensitize industry is served as the developing agent reductant and the protection of fixing bath dose and so on; sewage treatment.
2.For food additive
Bleach agent (e.g.candies, cake, bamboo shoots, etc);Loose agent (e.g.bread, cracker etc);Antiseptic and germicide (e.g.fruit juice, tinned foodbrews, the cereals food is defended storage etc);Inhibitor and freshen agent (e.g.day lily, seafood, fruit and vegetable etc)
Specifications:
Na2S2O5 97% min
SO2 65% min
Fe 0.0015% max
water-Insoluble 0.01% max
As 0.0001% max
PH 4.0-4.6
Packing and Storage
Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg/50KG/1000Kg/1200kg. Transportation-and harsh rain. Stored in a cool, ventilated, dry place.
High transparent addition cure silicone for Jewelry mold making is a kind of two part silicone
rubber in addition cure or platinum cure type with mixing ratio of 10:1. It can
be cures at room temperature as well as under heat. It's a kind of food grade
silicone ,And mainly used for jewelry mold making.
High transparent addition cure silicone for Jewelry mold making is pourable, addition-curing, two-component silicone rubber that vulcanizes at room temperature or by heating. Non-toxic, odorless.Resistance high temperature is 250, shrinkage rate lower than 0.1%.
It is great to make molds either with simple or intricate
patterns,like artificial jewelry, resin Jewelry , artificial necklace, artificial bracelet etc.
silicone molds serve very good performance in reproduction process with every fine detail on designing models.
8131 Addition Cure Silicon Rubber For Artificial Suppliers
Short on time? Let Addition Cure Silicon Rubber For Artificial sellers contact you.
