1.Description of addition cure liquid silicone rubber G-830 silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fastly by heating, Itâ??s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible. 2.Characteristics of addition cure liquid silicone rubber (1).An exceptional fluidity and good operability (2).Good tensile strength and tear strength (3).Food grade silicone rubber (4).high temperature resistance (5).good flexibility (6).No smell ,non-toxic (7).long shelf-time &lifetime (8).Lower shrinkage 3.Application of addition cure liquid silicone rubber G-830 silicone rubber is flexbile silicone rubber ,it has a higher temprature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing . Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
Molding silicone rubber, addition cure liquid silicone, pad printing silicone rubber, injection silicone rubber, electronic potting silicone rubbe 25kg/drum and 200kg/drum
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
Addition cure silicon rubber for artificial stone products pplications: It mainly use for making molds for resin, stone, gypsum and cement product with medium size. Addition cure silicon rubber for artificial stone products Typical Datasheet : Item No Color Hardness (A°) Viscosity (CS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2) Elongation-break(%) Mixing Ratio of silicone and catalyst Application(most for resin, stone, gypsum and cement product to make moulds) HY-E635 Translucent 35±2 8000±2000 =60 =13 =400 1:1 Addition cure silicon rubber for artificial stone products Points of attention: 1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse. 3,Addition cure silicone affect by temperature greatly when cured under room temperature. 4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. It’s fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it’s easy to make the catalyst to be poisoning. 5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa 6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it’s 1 : 1 or 10 : 1.
Addition cure silicone can be used for cake, candy food grade products mold making, addition cure silicone features low shrinkage.(features for low viscotity , good operation. Excellent performance. 25kg/drum and 200kg/drum
400 1:1 Most suitable for medium sized product Addition cure silicon rubber for artificial stone products advantages: Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller Addition cure silicon rubber for artificial stone products points of attention: 1, prone to poisoning, can not mix with condensation, ionic compounds containing n, s-, p, organic matter and of sn, as, hg, ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2, comparing with condensation cure silicone, addition cure silicone's adhesive properties to be worse. 3, addition cure silicone affect by temperature greatly when cured under room temperature. 4, addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. Its fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily, its easy to make the catalyst to be poisoning. 5, addition cure silicone rubebr has two-component, the component a and component b, please pay attention to clean the component a containers before using for the component b, and vice versa 6, in order to avoid the hardness change, we should mix the component a and component b according to its mixing ratio strictly, no atter its 1 : 1 or 10 : 1. 25kg/drum or 200kg/drum
Description of platinum curing mould making liquid silicone rubber Addition cure silicone is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 1:1 or 10:1. It can cure at room temperature as well as under heat. It's a kind of food grade silicone and mainly used for mold making. Application of platinum curing mould making liquid silicone rubber Silicone rubber is mainly used for making molds of tire, concrete stone, grc, polyurethane products; wax, candle decoration; rapid prototyping and tyre molds; chocolate, candy and similar products.
Addition cure Electronic Potting Silicone Rubber 1. Product Feature of Addition cure Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials. 2. Typical Application of Addition cure Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Addition cure Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. 4.Notes of Addition cure Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance. PACKAGE 40Kg/pail as a set (Part A 20Kg + Part B 20Kg) SHELF LIFE AND TRANSPORTATION 1. Twelve(12) months when stored at 24C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals. 3. Storage beyond the expired date doesnot necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons. -
Addition Cure rtv-2 Liquid Silicone Rubber for Concrete & Stone moulds Artificial Stone & Concrete Casting Silicone Rubber Features: Amazing fluidity and easy to operate Platinum-based, food-grade silicone (environmental friendly, odorless -and non-toxic) Delicate design available Mixing ration: 1:1, easy to mix Easy de-molding Excellent tension and tear strength High performance in duplication Shrinkage is almost zero (below 0.1) Excellent resistance to weather, temperature, aging, acid and aging-proofing. High resistance to high temperature and aging(resist -60â?? to 250â??) Appearance: Part A:a non-toxic and odorless liquid with translucent color and platinum inside. Part B: a non-toxic and odorless liquid with translucent color. ATT: We can do any curing time as your requirements. Technical Data Characteristics of the non cured product Properties G-820 G-825 G-830 G-835 G-840 A B A B A B A B A B Appearance low viscous liquid Colour translucent Density [g/cm 3 ] at 23 �°C, approx 1.10 1.10 1.10 1.10 1.10 Viscosity [mPa�·s] at 23 �°C, approx 5000�±1000 6000�±1000 7000�±1000 8000�±1000 9000�±1000 Polymerisation Curing conditions: 1h at 80 �°C Properties G-820 G-825 G-830 G-835 G-840 Hardness Shore A 20�±2 25�±2 30�±2 35�±2 40�±2 Tensile strength [N/mm 2 ] 45�±10 50�±10 55�±10 55�±10 60�±10 Elongation [%] 500�±50 500�±50 450�±50 450�±50 450�±50 Tear strength [N/mm] 22�±2 24�±2 26�±2 24�±2 12�±2 Application: GC RTV silicone G-8 series are great for artificial stone casting. They are widely used for architectural elements, block-outs & hole former, concrete counter tops, flexible form liners, GFRC, manufactured stone veneer, ornamental precast & statuary, stamped & textured concrete, etc. Operation Method: Both pouring and brushing operation methods for our artificial stone casting silicone are available. You can choose the best one as your preference, we can provide thixotropic agent for brushing. Notice What is the hardness should I choose? Normally 20~40 Shore A will be the best, but it also should according to your size and pattern design. Warm Tips: The surfaces with which the material comes in contact must be perfectly clean, free of grease and dry. Close the bottles after use so as not to confuse the cap of the catalyst with that of the base when re-sealing. Be aware of possible cross-contamination; it's highly recommended to use only dedicated gear when processing poly-addition RTV2 silicone rubber (including degassing devices). Be aware that contact with certain material can inhibit the curing of the RTV2 poly-addition silicone rubber. Common contaminants to be avoided include: -Natural or synthetic rubber, vulcanized with sulphur derivatives. -Poly-condensation RTV catalyzed with metallic salts. -PVC stabilizing agents. -Amine cured epoxies. -Sulphur, tin and amines derivatives. -In case of doubt, carry out a small test by pouring the mixture onto a small area of the object.
1. Description YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour. 2. Features *high chemical resistance to the aggressive components of some types of resin *High resistance to laceration (this characteristic guarantees high resistance to wear and tear) *High level of accuracy in reproducing very small particulars *High dimensional stability over time and non-deformability *Considerable resistance to high temperatures and to ageing *Excellent non-stick effect *Soft, stretchy, high tear resistance, *Will not shrink in service
Addition cure silicon rubber for artificial stone products Addition cure silicon rubber for artificial stone products pplications: It mainly use for making molds for resin, stone, gypsum and cement product with medium size. Addition cure silicon rubber for artificial stone products Typical Datasheet : Item NoColor Hardness (A-Viscosity (CS)Tensile-strength( kgf /cm2 )Tear-strength (kgf /cm2)Elongation-break(%)Mixing Ratio of silicone and catalyst,Application(most for resin, stone, gypsum and cement product to make moulds) HY-E635 Translucent 35,8000,2000;Y60,Y13,Y400 1:1Most suitable for medium sized product Addition cure silicon rubber for artificial stone products Advantages: Flexible, high and low temperature resistance, resistance to ultraviolet radiation, environmental protection, water repellent, good air permeability, good insulation, shrinking smaller Addition cure silicon rubber for artificial stone products Points of attention: 1,Prone to poisoning, can not mix with condensation, ionic compounds containing N, S-, P, organic matter and of Sn, As, Hg, Ph., easy molding plastic poisoning, resulting in the phenomenon of not curing. 2,Comparing with Condensation cure silicone, Addition cure silicone's adhesive properties to be worse. 3,Addition cure silicone affect by temperature greatly when cured under room temperature. 4,Addition cure silicone is easy to poisoning, please clean the tools which are used for condensation silicone rubber, so that it can avoid poisoning. It fobidden to add the pigment or powder to addition cure silicone rubber arbitrarily,it&easy to make the catalyst to be poisoning. 5,Addition cure silicone rubebr has two-component, the component A and component B, please pay attention to clean the component A containers before using for the component B, and vice versa 6,In order to avoid the hardness change, we should mix the component A and component B according to its mixing ratio strictly, no atter it 1 : 1 or 10 : 1. Addition cure silicon rubber for artificial stone products Package and storage : 1. 20kg or 200kg /drum. 2.It is a kind of non-dangerous goods, and it should be stored at a cool and dry place, please keep it from sun and rain. 1kg/drum 5kg/drum 20kg/drum 25kg/drum 200kg/drum
Silicone rubber for mold making Silicone rubber for mold making applications Silicone rubber for mold making is primarily intended for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry, a large statue Buddha, furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on. Silicone rubber for mold making description Silicone rubber for mold making is white or red flowing liquid with general hardness of 22-50A after curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength, tear strength and elongation. Frequently asked questions of silicone rubber for mold making Why does the silicone rubber mold have few molding times? The silicone rubber mold has few molding times is due to following reasons: adding too much silicone oil which will destroy the molecular of silicone rubber; making the mold for small and fine detailed products with higher hardness silicone rubber which is easy to break; making the mold for large products with soft silicone rubber which will reduce the tensile and tear strength of the mold, and the mold will have deformation. Thus, we should take the proper silicone rubber to make the mold for suitable products. Place of Origin Guangdong China Brand Name Hong Ye Silicone Rubber Model Number HY625 HY630 silicone rubber Minimum Order Quantity: 200 Kilogram Price: FOB shenzhen USD 5.8~7.5/kg Packaging Details: 25kg/drum and 200kg/drum Delivery Time: within 3 days after payment confirmed in our bank. Payment Terms: L/C,T/T Supply Ability: 8 Ton per Day Certifications:RoHS.MSDS.SGS ISO9001:2000 25kg/drum and 200kg/drum
Pad printing silicone rubber usages: Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toy, electroplating toy and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toy products surface. Pad printing silicone rubber features: Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free. Pad printing silicone rubber operation instructions: Pad printing silicone rubber is two-component silicone, part a is liquid silicon rubber, part b is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.G. We take 100g of liquid silicone rubber and 2g to 3g catalyst, mix them and pour it to your mold. After 2-4 hours, you will get a pad printing silicone rubber.. Place of originGuangdong china Brand nameHong ye silicone rubber Minimum order quantity:100 kilogram Price:Fob shenzhen usd 6.8-15.8/kg Packaging details:20kg/drum and 200kg/drum Delivery time:Within 3 days after payment confirmed in our bank. Payment terms:L/c, t/t Supply ability:8 ton per day Certifications:rohs.Msds.Sgs iso9001:2000 20kg/drum and 200kg/drum
a. Applications of Manual Molding Silicone Rubber: Manual Molding Silicone Rubber is mainly used for model design of manual mold, PVC plastic molds, cement products, low melting point alloy molds, alloy toy, plastic toy, electronics, handicrafts, large-scale sculpture, reproduction of cultural relic, sole molds, pad printing allocation, Electronic equipment anti-vibration, etc. b. Model Codes of Manual Molding Silicone Rubber: HY-528 is applicable to make molds of smaller products and the production will be 2 to 3 pieces. HY-540, compared to other two types, for its moderate hardness and better quality & performance, its production will be 20 to 30 pieces. HY-570is applicable to large size products duplications and Electronic equipment anti-vibration. b. Operation Instructions for Manual Molding Silicone Rubber: RTV-2 Manual Molding Silicone Rubber is a flowable liquid, and the quality has nothing to do with the color. It consists of two components. Part A is a flowable liquid silicone rubber, part B is the curing agent. Firstly, after your previous work of dealing with the original model, take some liquid silicone rubber , add 2% to 3% curing agent of the amount of silicon, and mix them evenly. Then after vacuum-pumping the mixture, you can pour it into the mold frame. The silicone mold will cured in 2 to 3 hours. Note: The time for vacuum-pumping should be less than 3 to 5 mins, otherwise, once the silicone rubber has cross-link reaction during vacuum zing, it will not be operated. FAQ of manual molding silicone rubber: How to prevent silicone manual molds getting sticky? The main reason for this problem is that you do not handle the products or original molds well, and then you should deal with the original mold or products carefully before molding. Such as for the products with a complicated pattern or an unsmoothed surface, you should polish and clean the products after which it will be molded, then spray the release agent. Normally, the release agent can be Vaseline, detergent. Liquid wax Etc. In practical process, you can bush different release agent according to different material. The second reason is that the operator pours the silicone into the mold when the mixture is mixed evenly, then the finish silicone mold will not cure and dry entirely. Place of Origin Guangdong China Brand Name Hong Ye Silicone Rubber Payment & Shipping Terms: Minimum Order Quantity: 200 Kilogram Price: FOB shenzhen USD 4.8~7.5/KG Packaging Details: 25kg/drum and 200kg/drum Delivery Time: within 3 days after payment confirmed in our bank. Payment Terms: L/C,T/T Supply Ability: 8 Ton per Day Certifications:RoHS.MSDS.SGS ISO9001:2000 25kg/drum and 200kg/drum
Platinum cure molding rubber silicone rtv is used for prototyping and the reproduction of parts. Silicone moulds can be constructed in many different forms depending on the shape of the part you are making. In this section we will outline how to create the easiest one part flat back mould. Silicone is the first choice of material when casting 3 dimentional shapes that contain undercuts as it exhibits excellent release properties, a high level of surface detail, very good chemical and high temperature resistance.
Nitrile butadiene rubber, also known as nitrile rubber , NBR, Buna-N, and acrylonitrile butadiene rubber, is a synthetic rubber derived from acrylonitrile (ACN) and butadiene. Product Paramenters Item Units Appearance Type QD-701 Appearance Milk white Solid content % 43.5-46% PH value Min 8.0 Viscidity mPa.s Max 40 Coagulum % Max 0.1 Mechanical stability % Max 0.1 Packaging 23tons /flexitank IBC drum*20, 20tons/FCL Shipping: Promote shipping usually 7--14 days after receiving TT deposit
Super Silicon Voga are natural silicon rich minerals that contain high amount of active silicon and other beneficial nutrients. Super Silicon Voga contains over 5,000 ppm of plant available silicon, 20 times higher than other brands. Silicon is known to be absorbed by plants and transported to plants' cell walls. It helps strengthen cell walls, as a result, more tolerance of pests and diseases. It also has high cation exchange capacity (CEC) which helps improve soil�¢??s physical and chemical structure and soil's capacity to retain nutrients and slowly release them to plant's roots.�?� In soils, it helps loosen up hard soils resulting in better root growth.�?� Not only preventing loss of nutrients,�?� it also makes them more readily available to plants. Silicon also helps release fixed phosphate from soils resulting in better flowering. Silicon accumulated on leaves make them more shiny and help reduce transpiration rate. It can reduce water usage by as much as 30% resulting in more drought tolerant. Produce with silicon will taste better and stay fresh for longer time. Super Silicon Voga can be used in a variety of ways. Mix with chemical fertilizers, it will help prevent loss of nutrients and provide source of silicon to plants. Mix when spaying fungicides or insecticides, it will enhance and prolong the substance's efficacy. It can also be used to cure fungal diseases on trunks. Benefits: - Enhance efficacy of chemical fertilizers, prevent leaching - Prevent fungal and other diseases - Strengthen plants, improve resistance against pests and diseases - Enhance efficacy of chemical fungicides and pesticides�?� - Absorb toxins from soils, fruits, and vegetables Usage: - Mix with chemical fertilizer, manure or organic fertilizer before applying to soils. Use 1 kg of Super Voga for 50 kg of fertilizers. - Mix with small amount of water to make paste. Apply paste on plant's trunk infected by fungi. - Spread small amount around canopy to prevent root rot. - Mix 1 teaspoon of Super Voga in 20 liter spraying tank when spray fungicides or pesticides to increase their effectiveness - Mix 1 teaspoon Super Voga in 5 liter water. Use it to clean vegetables or fruits to clean chemical residues and help prolong freshness.
Description SB4130 silicone rubber for trademark making is a kind of room temperature addition-cured liquid silicone rubber with low viscosity,which has all kinds of the advantages and features of addition cured silicone.Silk screen printing silicone is a free-flowing, ready-to-use silicone rubber that vulcanizes either at room temperature or at high temperatures under the influence of almospheric moisture. Application SB4130 silicone rubber can be used for making labels separately,and also can be fabricated into trademarks thorough cloth pressing and leather pressing.Generally,itâ??s applied to the trademarks of jeans,shoes,toys,etc. Characteristics - Resistant to high temperatures - Resistant to mineral oil and coolant - Solvent free - Long open time, suitable for screen printing -Â Can be colored with 3-5% Pigment Paste