4 Cervinus Stripe Paint Roller Suppliers and Manufacturers

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

Paint Roller

Name: 2-hydroxy-6-naphthoic acid Alias: 2,6 acid; 2-naphthol-6-carboxylic acid; 6-hydroxy-2-naphthoic acid; 6-hydroxy-2-naphthoic acid CAS NOï¼?16712-64-4 Molecular formula: c11h7o3 Molecular weight: 187.172 Product quality standard: Appearance characte Light yellow powder Content 99% 2-naphtholâ?¤0.10% 2,3-acidâ?¤0.10% melting point243-245�°C Loss on dryingâ?¤0.30% heavy metalâ?¤20ppm Application: used in medicine, liquid crystal, paint, etc. Packing: 25kg / cardboard barrel, or according to customer requirements

- Material: Natural bamboo 100% - Type: 4 steps, 5 steps,... - Process: Clean, no defects, polished, colored or natural, Coated with gloss paint, fumigated.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

Product Name: Hoi An Silk lanterns Function - Decor Restaurant, Hotel, Wedding, Party, Event,..., - Gifts Material: Bamboo, silk Color - White, Yellow, Red, Dark Red, Blue, Purple, Green,... ( see table color) - For indoor decoration : use pattern fabric for indoor - For outdoor decoration : use plain fabric for outdoor - Can hand painted flowers, bird,... ; Print logo on lanterns according to customer's design Size - Size is length of lanterns when they're folded. Depend of shape, the bigest size can be 180cm (70'') - Avaiable size :10cm, 20cm, 30cm, 35cm, 40cm, 50cm, 60cm, .... to 180cm Shape: We have 12 shapes for for your choice Country of Origin Producting at Hoi An, Viet Nam MOQ:100 units Sample Available Payment Term: Bank Transfer, Western Union, MoneyGram, Credit Card Time for production: 2 to 15 days (depend on quanlity). With small orders, We will send within 2 days Delivery time - 4-30 days (depend on quantity and transport service) - ho chi minh Air port, Sea port Remark - Handmade high quality and competitive price. - Welcome customerâ??s design

Factory Automatic Hot Eye Onion peeling process machine,from small capacity to big capacity Onion peeling process: the onion is manually fed into the hopper --- the conveyor belt automatically feeds the onion into the peeling box for peeling --- after peeling, the onion goes into the peeling roller. Under the action of high-pressure air at the side, the first and second layers of the onion are peeled off and sent out to complete the whole processing process. Features: 1. Advanced technology, reasonable mechanism, beautiful appearance, safe and reliable use, all stainless steel. 2. Automatic peeling without damage. 3. The depth of peeling is even. 4. The feeding belt is used for automatic feeding, which is simple in design and convenient in use. 5. Less peeling, high recovery rate of finished products, and over 98% of finished products. 6. Mechanical processing eliminates the hidden danger of manual processing of infectious diseases and unsanitary products. Parameters 1.process arrange diameter of round shape onion 30-150mm. 2.capacity 1000-1500kg/h 3.Power 3kw 4.Voltage 380V 5.Air Compressor :flow 1.5m2/min, pressure 0.7MPa ,power 11kw 6.Machine size 1.5*1.3*1.4m 7.Weight 420kg Start working flowing: 1.Fill onion in the loading box 2.Start the pneumatic valve switch 3.Start the power-supply switch 4.According to onion drying or fresh to adjust loading speed button/air pressure ,in order to ensure the clean degree of removing onion skin 5.When finished adjusting ,The equipment operates normally and automatically.