Hard drawn mesh is specified in AS/NZS 4671: 2001. Heyou wire mesh offers a range of mesh sheet sizes and certres to meet the needs of typical New Zealand applications.
Our scope covers standard sheet sizes of 4.65m x1.97m and larger economical sheets 6.15m x2.42m. The pitches are 150mm x150mm or 300mm x 300mm.
AS/NZS 4671: 2001 specification for hard drawn mild steel wire for concrete reinforcement
The mechnical property required by standard AS/NZS 4671: 2001
Nominal diameter(mm) Minimum 0.2% proof stress(Mpa) Tensile strength(Mpa)
Minimum Maximum
Up to and including 3.15 485 575 855
Over 3.15 485 575 775
The pitch (a) of longitudinal bars and transvers bars is not less than 50mm. The pitch is measured as below shown. The tolerance of the pitch is not more than 0.075 times the specified value.
Specification of hard drawn mesh
Equivalents are based on the nominal sectional area of steel per meter width.
Additional meshes specification are available as a special order.Minimum order quantities will apply. Please mail to us Heyou wire mesh for further details.
What does SE62 mean?
In standard AS/NZS 4671: 2001, the designates letters to be used to identify reinforcing mesh products:
Reinforcement steel mesh was welded by automatic electrical resistance welding machines conformance to standard AS-NZS 4761-2001.
The material of reinforcement steel mesh is 250N, 500N, 500L, 300E, 500E.
Reinforcement steel mesh is very poupular in civil engineering and construction. It always used on road subgrade, building foundation, tunnel support and reinforced,mine and coal reinforced and support, bridge construction etc.
During construction works, It is not only increase our working speed and time but also save 75% construction cost and enhance the crack resistance.
The specification of rectangular reinforcement steel mesh as below:
The panel size 2.4m*6m is very pouplar in Australian market,but considered the transportation in container by sea and saved cost, we advise the customers to change the panel size to be 2.2m x5.8m.
Heyou factory can produce concrete reinforcing mesh which is the specification of New Zealand standard AS-NZS 4761-2001.
Details of concrete reinforcing mesh:
Material: 250N, 500N, 500L, 300E, 500E
Mesh Pitch: 200mm
Wire: ribbed steel wire & plain steel wire
Overhang length of two sides: 100mm
Wire diameter:6mm, 7mm, 8mm, 9mm
Size: 2.4m * 6m or 2.2m * 5.8m
Packing: 1ton more or less per bundle
HS code: 73142000
Production Standard: AS-NZS 4671-2001
The specification of concrete reinforcing mesh as below
concrete reinforcing mesh specification
Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width
No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m
Structural and skatch
SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318
SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251
SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192
SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141
Non-structural
SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147
SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84
Are you a Manufacturer?
Heyou wire mesh factory as a professional factory for reinforcement mesh, which has 10 workshops, more than 200 workers, advanced production line,perfect production process, Strict production regulations.
We own ourselves laboratory for inspected chemical composition and mechnical property of raw material, drawn wire diameter measuring,cutting wire length measurement, and full pieces of concrete reinforcing mesh which contained pitch of wire to wire, shearing resistance, tensile strength, yeild strength, elongation, bend test, weight tolerance, size tolerance, ribbed height, pitch of transverse wire ribbed, surface quality and etc. We're strictly to do everything in order to guarantee our concrete reinforcing mesh quality.
Therefore, Heyou Wire Mesh has a high reputation in our field as real manufacturer.
Construction reinforcement mesh was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001.
The material is 250N, 500N, 500L, 300E, 500E, the mesh size is 150x150mm, wire diameter is 5.3mm and 4.0mm and the overhang length is in both sides. These specificate is very pouplar in New Zealand civil engineering field.
More features of construction reinforcement mesh and ours as below:
1. high quality raw material
2. electric resistance welding machine made it which has firmly solder join, size precision,and appearance good-looking
3. Professional management team
4. Complete QC rules and regulations
5. A full of laboratory testing instruments
Advantage of construction reinforcement mesh by AS-NZS 4671-2001 standard:
1. Save 30% of steel bar dosages
2. Reduce 50%-70% work time, improve construction progress and shorten construction period.
3. Cut down 5%-10% construction cost
4. Used widely,it has a good market development prospects.
The specification of construction reinforcement mesh by AS-NZS 4671-2001 standard as below:
concrete reinforcing mesh specification
Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width
No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m
structural
SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318
SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251
SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192
SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141
Non-structural
SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147
SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84
17797 Wires Cables Suppliers
Short on time? Let Wires Cables sellers contact you.
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm.
the steel bar after drawing shape as below figure:
1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45. The angle scope is greater than 45 and is less than 70, the rib height is from 0.025d to 0.10d.
2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost.
Steel pallet for reinforcing mesh size 2.4m *6m Loading container for reinforcing mesh sheet: 2.4m *6m
3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars.
4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels.
Notes:
1. Grade 250N is supplied as plain round reinforcing steel complying with AS 3679. 1, exceptthe tolerance of the diameter and roundness dosen't apply it.
2. For 500L steel bars, only requriement for wire diameter is less than 5.0mm is RekL 500
Material certificate of reinforcing mesh as below:
Common size of Squre reinforcing mesh panel for Austialian Market
Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width
No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m
Squre, with edge side-lapping bars
SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354
SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290
SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227
SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179
SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141
Squre, without edge side - lapping bars
SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454
How can we conctrol our products quality for exporting Autralia?
Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechanical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3.
Secondly, the panel size tolerances measure way as:
a. Panel Size dimensions 6m in length, there is 40mm tolerances.
b. Panel size dimensions 6m in length, the tolerance is �±0.7%
c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract.
d. Weigh the each bundle weight to calculate each panel weight.
The slab mesh reinforcement is used on footing construction, beam and piers of waffle rafts. The slab mesh was made by Heyou wire mesh factory accordance with AS NZS 4671-2001.
the popular specification is SL102, SL92, SL82, SL72, SL63, SL53, L8TM, L11TM, L12TM in the Australia and New Zealand civil engineeing. The slab mesh reinforcement includes reinforcement mesh and trench mesh. Aoriding to different construction site, they use the spcification of slab meshes are difference.
Slab mesh reinforcement for footing slab, beam and piers
The full of slab mesh reinforcement specification as below:
REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8
L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2
L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6
L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9
L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9
L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72
L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13
L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7
L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3
L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8
L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34
L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1
L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3
L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8
L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3
L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8
L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1
Slab mesh reinforcement for footing slab, beam and piers
RIBBED RECTANGULAR MESH
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
RL718 6 x 2.4m Sheet 25 x 6.75 @ 100 30 x 7.60 @ 200 67
RL818 6 x 2.4m Sheet 25 x 7.60 @ 100 30 x 7.60 @ 200 79
RL918 6 x 2.4m Sheet 25 x 8.60 @ 100 30 x 7.60 @ 200 93
RL1018 6 x 2.4m Sheet 25 x 9.50 @ 100 30 x 7.60 @ 200 109
RL1118 6 x 2.4m Sheet 25 x 10.70 @ 100 30 x 7.60 @ 200 130
RL1218 6 x 2.4m Sheet 25 x 11.90 @ 100 30 x 7.60 @ 200 157
Slab mesh reinforcement for footing slab, beam and piers
REINFORCING MESH TO AS/NZS4671:2001 / RIBBED SQUARE MESH 6.0 X 2.4 METRES
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
SL52 6 x 2.4m Sheet 10 x4.77 @ 200 + 4 x 4.00 @ 100 30 x 4.77 @ 200 21
SL62 6 x 2.4m Sheet 10 x 6.00 @ 200 + 4 x 4.24 @ 100 30 x 6.00 @ 200 33
SL72 6 x 2.4m Sheet 10 x 6.75 @ 200 + 4 x 4.77 @ 100 30 x 6.75 @ 200 41
SL82 6 x 2.4m Sheet 10 x 7.60 @ 200 + 4 x 5.37 @ 100 30 x 7.60 @ 200 52
SL92 6 x 2.4m Sheet 10 x 8.60 @ 200 + 4 x 6.00 @ 100 30 x 8.60 @ 200 66
SL102 6 x 2.4m Sheet 10 x 9.50 @ 200 + 4 x 6.75 @ 100 30 x 9.50 @ 200 80
SL81 6 x 2.4m Sheet 25 x 7.60 @ 100 60 x 7.60 @ 100 105
Slab mesh reinforcement for footing slab, beam and piers
SQUARE MESH 300 X 300 SPACING TO AS/NZS4671: 2001
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
SL53 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 14
SL63 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 21
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire
It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam.
Specification of trench mesh reinforcement
Surface treatment:galvanized or drawn wire
Material: R250N, D500N, D500L, D300E, D500E
The Tensile strength is 300Mpa.
The trench mesh was produced by standard AS NZS 4671-2001
Width: 0.2m - 2.3m
Length: 6m
REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8
L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2
L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6
L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9
L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9
L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72
L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13
L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7
L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3
L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8
L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34
L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1
L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3
L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8
L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3
L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8
L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1
Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers
And Alls of using is accordance to AS NZS 2870-2011.
1. Footing slap
The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments.
The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different.
2. Waffle rafts beam and piers
The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft:
(a). pier to be located on the intersection of every third internal beam.
(b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
Roll length
30m, can be customized
Diameter
0.025-1.60mm
Width
0.914m, 1.0m, 1.22m, 1.5m, 3.0m
Business type
Manufacturer and trading company
Usage
Filter
Material
SS202, 304, 304L, 316, 316L, 430, 904 and 904L and other special materials.
Product presentation
(1)As a Faraday cage.We recommend the 200x /250x /300x.
The wire mesh on the surface of a Faraday cage make a hollow conductor, in which the charge remains on the external surface of the cage.
(2)For the RFI and EMI shielding, 100x /145x /200x is the nice choice. The RFI (radio frequency interference) shielding is a method of protecting electronic devices and technological systems from damaging electromagnetic interference (EMI).
(3)Filter and sieve, you can choose our 50x /100x /150x wire mesh, also we provide customized any size and shape.
(4)Decoration: most customers chose the 50x /80x/100x for the purpose. The red copper wire mesh decoration is beautiful and sturdy.
Detailed description
Product name Faraday cage RFI and EMI shielding red copper wire mesh
Material 99.99% copper
Size 40*12 inch(100*30cm)
Weaving type PW/TW/DW
The max mesh counts 400
Hot sales counts 80x/100x/150x/250x/300x
Advantage Conductive, Electromagnetic shielding, Wear resistance, Sound insulation etc.
Model K-2020-06-1
Shipping 1*red copper wire mesh
Packing & Shipping
(1)Paper tube + wrapped with water proof film + craft paper+ bubble pad + wooden box.
(2)Special packing: According to customer needs.
Company Introduction
Our company was established in May 2019, and currently
mainly deals in the wholesale and retail of metal products,stainless steel products, metal filters, mechanical products,metal materials, decorative materials, construction materials, hardware, electrical and electronic products. The company address is Jianhua E-commerce Industrial Park, Shangtang Street, Gongshu District, Hangzhou, ZheJiang, China.
FAQ
Q.Are you factory/manufacturer or trader?
We are direct factory who owns production lines and workers. Every thing is flexible and there is no need to worry about extra charges by the middle man or trader.
Q.Can I get free samples?
If the sample is available, yes ,can be free. If unavailable,need to customize.
Q.How long is your delivery time ?
Usual it is 5-10 days if the goods are available in stock.or it is 15-20 days if customized
Q.What is your minimum order quantity?
Actually there is no MOQ for our products. But usually we recommend a quantity based on the price which is easy to accept.
"Ti-wire" high proformance
titanium welding wire and filler metal are offered in sizes 0.8 - 4.0 mm (1/32"-5/32") with AWS A5.16/5.16M, AMS 4951,
AMS 4954 for aerospace, medical, chemical & industrial etc.
Description
Yitong Stainless Steel Filter Housings are industrial filter housings that accommodate different diameter filter cartridges and conform to Chinese national standard. These rugged housings offer all stainless steel construction and have great leakprofness. These Filter Housings are compatible with a wide range of fluids. Various cartridge types can be used including Wound, Melt Blown, Pleated, Carbon, Resin Bonded, Stainless Steel and others. The polishing tech is used on the inside and outside surface to avoid the rust problem.
Features
1 It has various interface for filter cartridge, use the advanced numerical control machinery to process it
2 The surface finish outside is 0.4 micron, inside is 0.3 micron.
3 Comply with ISO2852 standard, the connector of the pressure gauge is adopted the â??Râ?? quick connector with Plane welding.
4 The height of the housing is adjustable.
Application
Prefiltration and clarification filtration of different industries, including pharmacy, chemical, beverage and liquor industries.It is also suited well in the production of sterilizing air in the fermentation system.
gyratory sifter can be equipped with one to nine layers of screen, which can complete the sieving from 12 mesh to 325 mesh. It can be designed as duplex screening to make it more productive. The design is compact and energy efficient.
Spring Clip Strainer/ In-Liner Tensioner Wire Strainer For Farm Work
Spring Clip Strainer Basic Information
An in-line wire strainer allows you to keep up to 4,000 feet of high tensile wire tight by allowing you to re-tension the wire whenever it is required. You need at least one wire strainer per fence wire, more strainers depending upon length of the wire. Once installed you simply tighten the in-line wire strainer using a ratchet handle.
Product Features
Item
In-line Tensioner Wire Strainer
Description
In-line Strainer(wire cilp) with a hole on the bottom
weight
175.6g
Material
Heavily galvanized strap, zinc coating 275 g/m2
package
50pcs/carton
carton size
280*280*280mm
Color
white
Delivery port
Tianjin XinGang Port
This fence strainer can be used to tighten poly wires, barbed wire and high tensile wire. In-line wire strainers keep your wire fence in top shape with minimal effort.
Spring Clip Strainer Specifications
For high tensile wires up to 200,000 PSI
Heavy cast cog with spring loaded latch
Hot dipped galvanized - No raw uncoated steel edges
Here is the sample below gor strainer wire
Spring Clip Strainer Features
1.Suitable for high strain conditions
2.Spring clip design for wasy tensioning
3.Galvanized frame with aluminum spool
4.Rust resistant
5.Robust and easy to use
Tumbler Screen is used for the treatment of valuable powders, pellets and granules. For applications in pharmacy, food and fine chemicals produces tumbler and vibration screening machine according to GMP.
Strainrite Wire Strainers And Post Pullers For Fence Tension Wire
Wire Strainer Features introduction
Easily adjusts wire tension on the fence line
Steel then galvanized
Galvanized strap
Designed to be used with a 1/2'' drive ratchet or crescent wrench.
Wire Strainer Description
An in-line wire strainer allows you to keep up to 4,000 feet of high tensile wire tight by allowing you to re-tension the wire whenever it is required. You need at least one wire strainer per fence wire, more strainers depending upon length of the wire. Once installed you simply tighten the in-line wire strainer using a ratchet handle.
This fence strainer can be used to tighten poly wires, barbed wire and high tensile wire. In-line wire strainers keep your wire fence in top shape with minimal effort.
Wire Strainer Technique Data And Features
Product Technique Data And Features
Item
Strainrite Wire Strainers And Post Pullers For Fence Tension Wire
Description
In-line Strainer(wire cilp) with a hole on the bottom
weight
175.6g
Material
Heavily galvanized strap, zinc coating 275 g/m2
package
50pcs/carton
carton size
280*280*280mm
Color
white
Delivery port
Tianjin XinGang Port
Wire Strainer Specifications
For high tensile wires up to 200,000 PSI
Heavy cast cog with spring loaded latch
Hot dipped galvanized - No raw uncoated steel edges
Here is the sample below gor strainer wire:
Wire Strainer, Available in Various Sizes and Colors, Customized Specifications are Accepted
Special Feature
With galvanizing or power coating
Construction concrete
Available in various sizes and colors
Used in fencing reinforcement
Customized specifications are accepte
Wire tensioner, use good tensile strength steel plate to make, have hot dipped galvanised or powder coated surface treatment. It used in chain link fence, wire fencing, vineyard trellis,barbed wire, euro fence, filed fence and so on, to tie the wire at corner or end post.
Detailed Specification of the Steel Fence Wire Tensioner Strainer
Width
Height
Length
T/Dimension
30mm
20mm
95mm
Ã??1,0 - 2,0 mm
30mm
20mm
95mm
Ã??1,0 - 2,0 mm
35mm
25mm
100mm
2,0 - 3,0 mm
45mm
30mm
120mm
Ã??3,5 - 5,0 mm
Weight
80g,90g, 100g, 120g, 180g, 200g
Length: 100mm,120mm, 125mm
Weight: 80g,90g, 100g, 120g, 180g, 200g
Surface treatment: Powder Coated, Galvanized
Packing: 30pcs/carton, 50pcs/carton
Using: Used with wire fencing, vineyard trellis,barbed wire, chain link fence, euro fence, filed fence
Color Could be OEM
Send me your detailed Spec and then the best quota would be sent.
Your satisfy is our goal.
Electric Fence Single Hole In-Line Wire Strainer Fence Tightener Set of 10
In-Line Wire Strainer Fence Tightener Usage:
1. Use to tighten high-tensile wire
2. Adjust using standard wrench
3. Galvanized steel, works on high tensile wire
4. Should be installed every 2,000 to 2,500-feet
5. Should be located in the middle of long runs of wire or between two corner posts
Features
1. Suitable for high strain conditions
2. Spring clip design for wasy tensioning
3. Galvanized frame with aluminum spool
4. Rust resistant
5. Robust and easy to use
Product Specification
Item
Line Wire Strainer
Description
In-line Strainer(wire cilp) with a hole on the bottom
weight
175.6g
Material
Heavily galvanized strap, zinc coating 275 g/m2
package
50pcs/carton
carton size
280*280*280mm
Color
white
Delivery port
Tianjin XinGang Port
An in-line wire strainer allows you to keep up to 4,000 feet of high tensile wire tight by allowing you to re-tension the wire whenever it is required. You need at least one wire strainer per fence wire, more strainers depending upon length of the wire. Once installed you simply tighten the in-line wire strainer using a ratchet handle.
This fence strainer can be used to tighten poly wires, barbed wire and high tensile wire. In-line wire strainers keep your wire fence in top shape with minimal effort.
Specifications
For high tensile wires up to 200,000 PSI
Heavy cast cog with spring loaded latch
Hot dipped galvanized - No raw uncoated steel edges
Our Service
Reasonable price and best service!
Warmly welcome customers to send inquiries, specifications and drawings for OEM processing. We would do our best satisfying your demand in collaboration. Thank you for your support.
Heavy Duty In-Line Wire Strainer With Compression Clip /Wire Tensioner
In-Line Wire Strainer Description
Wire tensioner, use good tensile strength steel plate to make, have hot dipped galvanised or powder coated surface treatment. It used in chain link fence, wire fencing, vineyard trellis,barbed wire, euro fence, filed fence and so on, to tie the wire at corner or end post.
Detailed Specification of the Steel Fence Wire Tensioner Strainer
Width
Height
Length
T/Dimension
30mm
20mm
95mm
Ã??1,0 - 2,0 mm
30mm
20mm
95mm
Ã??1,0 - 2,0 mm
35mm
25mm
100mm
Ã??2,0 - 3,0 mm
45mm
30mm
120mm
Ã??3,5 - 5,0 mm
Weight
80g,90g, 100g, 120g, 180g, 200g
Length: 100mm,120mm, 125mm
Weight: 80g,90g, 100g, 120g, 180g, 200g
Surface treatment: Powder Coated, Galvanized
Packing: 30pcs/carton, 50pcs/carton
Using: Used with wire fencing, vineyard trellis,barbed wire, chain link fence, euro fence, filed fence
Color Could be OEM
Send me your detailed Spec and then the best quota would be sent.
Your satisfy is our goal.
17797 Wires Cables Suppliers
Short on time? Let Wires Cables sellers contact you.
