We supply a variety range of steel products for construction sites, engineered plants, and interior appliances, such as: 1. Welded steel wire mesh 2. Welded steel wire fence :chainlink fence,wire partition inside the factories 3. Steel Works : the popular fences : wrought iron fences, ornamental fences, temporary fences, steel barriers, steel gate, and doors, and automatic gate system packages, included swing gates, sliding gate, and barriers, balcony 4. Wire products : wire partition, and security cages, display grill, wire shelves, wire lockers, wire cages & barns, ect. Container.
Noise Barrier
Power cable Spaced Aerial Cable, SAC 15kV, 25kV, 35kV
Power cables Aerial Bundle Cables, LV - ABC AX
POWER CABLE, Medium voltage cables armoured
POWER CABLES Fire Resistant & Flame Retardant Cables Please contact us for for details catalogue
POWER CABLE Medium voltage cables Please contact us for for details catalogue
POWER CABLE Low voltage cables Please contact us for for details catalogue
1.Solid or stranded copper/aluminum conductor 2.Insulation with XLPE, PE, or PVC 3.For cables of two-phase or three-phase conductors, round or flat shape available 4.PVC inner COVERING 5.Concentric layer of helically layed copper/aluminum wires 6.Wrapping tape 7.Black XLPE, PE, or PVC jacket The concentric cable is used in electric service entrance from the power distribution network to the meter pannel(especially where it is required to prevent electricity theft), and as feeder cable from the meter pannel to the distribution pannel. This cable an be used in dry and wet places, outdoors or directly buried. It has a maximum operating temperature of 90�ºC and rated voltage of 600V&below.
Aerial Bundle Cable (ABC) low voltage cable for overhead power distribution offering higher level of safety and reliability and lower power losses than bare conductors. Phase Conductor: Concentric strand or compressed 1350-H19 conductor Neutral Conductors: aluminum alloy 1350-H19,6201-T81, or ACSR conductors Insulation: high density polyethylene (HDPE) or cross-linked polyethylene (XLPE).
Compatible with Cat 5e, Cat 6 networks modems, routers, LAN, computer cables. Class 7 (Class F) cable Standard: Cat 7, S/STP; Conforms to TIA/EIA-568-B.2-10 specifications Contact Plating: Each shielded RJ45 connector has 50 micron gold plated pins Conductor wire gauge: 30 AWG Cable performance: up to 600 MHz Cable construction: 8 strands of multi-strand shielded copper stranded wire
1. Low voltage cables; 2. Medium voltage cables; 3. High voltage cables; 4. Thermal resistant conductor, low loss conductor; 5. Bare conductor; 6. Fire resistance cables; 7. Building wires
JPC is a cable assembly manufacturer serving the electronics assembly sector. - NEV (New Energy and Vehicles). - CCDC (Cloud Computing and Data Communications). - IoT (Internet of Things). - CE (Consumer Electronics). - SCI (Smart Connection Industrial). We maintain manufacturing facilities in Saigon Hightech Park, Thu Duc, Ho Chi Minh City, Vietnam. Our products are currently exported directly from Vietnam to the United States and Europe for clients in the Energy solutions, Databases, EMS, and Automotive industries.
Svr3 is made from latex in rubber plantation in binh phuoc province. It is used for the products which have light colour, require high quality such as: electricity cable wire, belt, sole of shoes, medical products, electrical engineering, ... Technical specifications of svr under tcvn: 3769 : 2004 Tcvn: viet nam exporting of natural rubber standard Properties Svr 3l - dirt content, % wt, max 0.03 - ash content, % wt, max 0.50 - nitrogen content, % wt, max 0.60 - volatile matter, % wt, max 0.80 - initial plasticity (po), min 35 - plasticity retention index (pri), min 60 - colour index, max 6 - mooney viscosity ml (1 + 4) 100c - cure r
Tie wire with diameter from 1mm
Cable Grout Industry standard high performance grout for the grouting of cables in post-tensioned concrete, void and fissure grouting, etc. Description A specially formulated Portland Cement shrinkage-compensated powder mix designed for the grouting of cables in post-tensioned concrete. The material readily mixes with water to produce a particularly fluid flowing grout which will penetrate and fill fine voids within and around the cables then harden without shrinking to give a high strength product. Uses include grouting of cable ducts, voids and fine fissures, support of cable anchor plates and ground anchors. Also to provide bearing or contact between structural elements, for grouting behind shafts and tunnel linings, and for underpinning, loose floor and road slabs. Once hardened and cured, high compressive strengths are achieved giving resistance to static and dynamic stresses. Cable Grout has a total chloride, sulphate and sulphide-ion content below that specified Advantages Does not contain aluminum powder nor any components which generate hydrogen gas, cardon dioxide or oxygen. Silica fume enhanced for low permeability. Non-metallic; will not stain or rust. Non-corrosive; does not contain chlorides. Zero bleed, even at high flow Excellent for pumping: Does not segregate, even at high flow. No build-up on equipment hopper. Superior freeze/thaw resistance. Even with his great fluidity, it can disperse water (thixotropic) Preparation - Genetic tubes must be cleaned with a high-pressure air compressor - Check the vents and pressure test for gen tubes - Repair leaks before grouting pumb Mixing - Water : mortar powder = 1 : 3.4 parts by weight. (6.8 litres of water per barrel) - With volume 15 liters: Use a colloidal solution mixer (to get the best results) Add water and continuously mix for 5 minutes to achieve a uniform Continue to maintain slowly mixing during grout pump Important Note Non mixing by hand Yield As a guide 1 barrel yields approximately 14 litres of mortar Shelf Life: 9 months Packaging: 25kg/barrel Storage Conditions - Store properly in dry conditions in undamaged and unopened original sealed packaging Cleaning of tools - Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed
Cais Electronics Co. Ltd is a company specialized in electric/electronic parts manufacturing and developing parts and new products with injection molding. We develop, manufacture, and supply cable ties, fixing appliance for electric wire, and cooling& heating boxes/cosmetics refrigerators/induction range for vehicles. Since the acquisition of abroad quality certification in 1992, we have supplied major companies with high-quality products. We do our best to research for new products development and produce high quality products based on information on the advanced industries and have the substantial and stable operational policies in infinite global competition age. Contact us today.
We are the professional manufacturer for Cable tray, Cable ladder, Cable trunking with many kind of finished product materials : HDG, Pre-painted steel, power coating.
We produce and install so many Low voltage MSB, Control panel, Distribution borad, Switch board, MCB consumer units for 5 stars hotel, resort, apartment, factoty, restaurant, hospital, school....
