VFLOOR2 are two component waterproof Self Leveling Mortar. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings. Suitable for prepairing interior floors prior to laying parquet, vinyl sheet and tile, soft floor covering, natural stone, ceramic tiles, etcâ?¦ It can be used on a wide range of absorbent and non-absorbent floor surfaces including concrete, cement and sand screeds, terrazzo, asphalt, ceramic & quarry tiles. Layer-thickness 2-10mm Can be pumped Product name: Self leveling concrete without primer VFLOOR2 Compressive strength: >35 Mpa, 28 days later Flexural strength: >7 Mpa, 28 days later Application Temperature: 5-30 degree Mixing ratio: 20kgs powder + 5kgs Liquid Feature & Benefits: - Two component, just mix A+B - Waterproofing - Good adhesion to primed substrates - Good flow, self smoothing - Rapid setting and early strength - Easy and quick to lay Mixing: Convenient easy mix ratio A:B = 4:1 by mass. Mix slowly and continuously to form a homogeneous mixture. The mixed materials is immediately ready to use and should be used within 30-40 minutes after mixing. Ready for foot traffic after approx. 24 hours. Drying time: Prevent draughts across the floor to avoid localized premature drying At ambient temperature, VFLOOR2 will appear to be dry after approximately 24 hours, ready for foot traffic after approx. 24 hours. Floor laying may commence after 48 hours. Coverage: At an application thickness of 2mm the coverage will be approx. 5kgs per 1m2 Shelf Life: 9 months.
Description: Repair 1 : is a one component cement based polymer modified high build repair and reprofiling mortar Usage: - For repairing all types of structures - Overhead and vertical repairs - Hand applied repairs - For exterior and interior use Advantages: - Just add water - Can be used on horizontal and vertical surfaces Surface Preparation: - The surface must be clean, dry, smooth and solid. - Particles hampering adhesion like dirt, oil and paint must be removed from the surface. - Highly absorbent surfaces must be saturated with water before application. No water accumulation should be left on the surfaces. Colour: Grey Shelf Life:18 months from date of production if stored properly in original, unopened and undamaged sealed pack. Storage Conditions: Store in dry conditions. Protect from moisture and direct sunlight. Packaging: 25kg/barrel and 5kg/ barrel
Description Crack PU is a 2-component, 100% solids, moisture-tolerant, epoxy adhesive. It is a low-viscosity, high-strength adhesive formulated specifically for grouting both dry and damp cracks. Where To Use Use neat for gravity feed or pressure injection of cracks in structural concrete, masonry, wood, etc. Seal interior slabs and exterior above grade slabs from water, chlorides and mild chemical attack and to improve wearability Advantages - Tenacious crack-sealing grout. - Convenient easy mix ratio A:B = 2:1 by volume. - Advanced low-viscosity structural resin. - Unique, high-strength adhesive for (canâ??t dry) cracks. Usage Crack PU is used to fill and seal cavities and cracks in structural components such as columns, beams, foundations, decks and waterretaining structures. It not only forms an effective barrier against water infiltration, but also bonds the concrete sections, together, thereby restoring original structural strengths. Shelf life Expiry date 18 months from the production date Storage conditions Dry, cool, shaded place Packaging 1) Combo A: 2kgs - B: 1kg Component A is clear liquid: 2kgs/ plastic can Component B is clear liquid: 1kg/plastic can 2) Combo A: 5kgs - B: 2,5kgs Component A is clear liquid: 5kgs/ plastic can Component B is clear liquid: 2,5kgs/plastic can 3) Combo A: 10kgs - B: 5kgs Component A is clear liquid: 10kgs/ plastic can Component B is clear liquid: 5kgs/plastic can 4) Combo A: 20kgs - B: 10kgs Component A is clear liquid: 20kgs/ plastic can Component B is clear liquid: 10kgs/plastic can 5) Combo A: 30kgs - B: 15kgs Component A is clear liquid: 30kgs/ plastic can Component B is clear liquid: 15kgs/plastic can
Description Hardener Liquid: is Dustproof, shiny, sodiium silicate-based water repellent liquid surface hardener designed for application to concrete and cement based floors. It penetrates deeply into the surface zone of the concrete and provides permanent hardness. Applications - Airplane hangars - Electronic assembly plants - Manufacturing plants - Warehouses and distribution centers - Shipping and receiving areas - Maintenance facilities - Commercial and industrial floors - Where light-reflective flooring is desired - Floors subject to heavy or frequent traffic - Multi-purpose sporting facilities Application steps Preparation: Grinding of concrete floors by sandpaper grinder and take away all debris, cement powder on the floor surface and then clean it Spray onto the concrete surface. Spray 2 coats. Each spray is 24-48 hours apart Important Note - If the paint becomes stagnant can appear white chalk phenomenon - If the layer is too thick it will can not dry out Storage Conditions Product must be stored in original, unopened and undamaged sealed packaging in dry conditions Colour Clear Shelf Life 12 months from date of production Consumption - 3kg Liquid: approximately application 15 m2 - 7,8kg Liquid: approximately application 40 m2 - 30kg Liquid: approximately application 150 m2
We are a supplier of marble in . The stone meets export standards.
Length 300 mm Width 300 mm Thickness 24 mm Specifications Wood species: Acacia, Teak, Eucalyptus, Keruing Wood Color: natural, dark brown, or customizable Number of slats: 6 or 12 Moisture: 8 12 % Length & Width tolerance: 0/+3mm Thickness tolerance: +/- 0.2 mm Glue: D4 Quality: ABC or customizable Component: wood part with interlock plastic base Installing area: 11 pieces/1m2 (square meter).
Size Customized Material 100% Natural Marble Stone Process Cutting by machine, Split, Horned, Polished Surface Packing Standard export wooden crates with fumigation and wraped protective film Supply Ability 100000 square meters per month
The Abaco Truck A-Frame is designed for storing stone slabs in workshops, exhibitions, warehouses, factories, etc. - Steel material makes the device highly rigid and ensures a heavy load to work. - Two sides of A-Frame and a cross bar are connected by bolts and are easy to assemble and disassemble for transport. - The timber blocks on the steel base prevent damage to the slabs. It is easy to package and transport. - Truck A-Frame is made of steel. - This Truck A-Frame has a simple A-Shape, but this shape provides efficient and reliable functions to allow stone slabs to lean back. It is constructed with two sides of A-Frame joined by a cross bar which makes the Truck A-Frame more sturdy.
