Construction PU Sealant is a one-component, low-modulus polyurethane sealant that cures on exposure to atmospheric humidity. It possesses excellent adhesion to all typical construction materials such as cement based materials, brick, ceramic, glass, wood, galvanized and painted sheet iron and various plastics.
Possesses permanent elasticity.
25 % movement capability.
No surface tackiness after full cure.
Do not pick up dirt.
No shrinkage.
Cures bubble-free.
Enhanced storage stability.
No sagging Thixotropic.
Can be applied with hand gun and tooled easily.
Paintable.
We are Yorm Company, under the umbrella of Yorulmaz Group since 1969, specialized in Building and Construction Materials. Our head-office is situated in Istanbul. We are supplying following products:
This device operates with 1 or 2 measuring cells. After entry of test-specific sample data into the controller, the test is completely automatically carried out and evaluated. The device has an interface for a generally commercially available printer. Scope of equipment delivered: automatic air permeability tester, 1 bottle of fill oil,
500 ea. Round filters (diam. 41 mm),
100 ea. Dust filters (diam. 13 mm),
1 ea. Tamper
Dimensions: 200x160x400 mm
Weight: 12 kg
Dimensions
5599 Construction Materials Suppliers
Short on time? Let Construction Materials sellers contact you.
Speed rate control: motor speed control unit
Load measure compression:450 bar press.Trans.
Load measure flexure: 250 bar pressuretransducer
Oil flow control : 24 v selenoid valve
Power : 220-240 v 1 ph 50 hz
Dimension: 600 x 600 x 1400 mm
Weight : 1350 kg.
The jolting group is connected to the table by bayonet joints for quick checking of the weights. The drop height 15, 0 mm is adjustable to keep it correct also after intensive uses. The apparatus is supplied with control panel including main switch, automatic digital drop counter, start/stop push buton
Power: 220-240 v, 1 faz, 50 hz, 500 w
Dimensions: 1000x380x420 mm
Weight: 60 kg.
Gypsum/ water ratio: 10 kg of gypsum for 6-7 lt of water
Work 90 dak.
Fýnal setting time: 150 dak.
Standard: TS EN 13279–1
The specification defined above may vary depending on site conditions and base characteristics.
The FOAMCEM light weight cellular concrete is obtained mixing liquid cement grout, or sandcement grout, with the foam made from our foaming agent foamcem.By this system a structure of closed air bubbles is formed into the mix and this fact takes an high insulating power and lightness to the material.Foamcem technology allows, varying the foam-cement-sand ratio, to obtain light weight cellular concrete with a density from 300 to 1.600 kg/m3 according to requirements.
Packaging: metal drums 230 kg net weight.
Consumption: kg 1, 5-2 cubic meter of cellular concrete depending on the density produced.
Used to adhere faience, ceramics and such materials. Easy to prepare and apply, with high stability, cement based and grey colour adhesive. Along above materials, in all kind of indoor/outdoor horizontal-vertical of concrete, plaster and cement-based surfaces applications.
Applications
òIndoor/Outdoor
òFixings tiles and ceramics on wet cement-based surfaces like bath, kitchen and balcony.
òEach packages are 25 Kg.
Descriptions:
Chamotte refractory block is made from high quality calcined fireclays. It is widely used in float glass furnace bottoms and in multi-course furnace bottoms. Its glass contact qualities. Also make it suitable for day tanks and other special glass contact applications.
Applications:
Chamotte brick is mainly used for furnace and hot blast stove, furnaces of metallurgic, Building material, glass, ferrous metal etc.
Descriptions:
Insulation brick is made from high purity refractory clays and other raw materials, with light
Weight and mini-porosity well distributed. It has advantages of low thermal conductivity, low
Heat storage, high spalling resistance, high hot compressive strength, how iron oxide and
Alkali flux content, accurate dimensions.
Applications:
It is widely used for insulating layer and lining of industrial kilns & furnaces.
Descriptions:
Mullite bricks have the properties of high purity, good mechanical strength, high refractoriness under load and low thermal conductivity. Mullite bricks are the best suited for reducing atmospheres and have resistance to slag and alkali attack. It has superior resistance to abrasion and thermal shocks. The effect on energy saving is significant.
Applications:
It is the ideal to be used as both insulating linings and working linings of high temperature kilns like glass tank furnace, kiln furnitures for firing ferrites, high alumina ceramics, carbon black reactor, cement kiln, burner blocks.
Descriptions:
High-alumina bricks are made from bauxite, a naturally occurring material containing aluminum hydroxide (al[oh]3) and kaolinitic clays. These raw materials are roasted to produce a mixture of synthetic alumina and mullite.
By definition high-alumina bricks contain between 60 and 95 percent alumina and much more robust than fireclay refractories at high temperatures and in basic environments.
In addition, these bricks exhibit better volume stability and abrasion resistance.
Applications:
High-alumina bricks are used in blast furnaces, blast-furnace stoves, liquid-steel ladles, steel refining furnaces, glass tanks, ceramic kilns, enamel kilns, rotary cement kilns and other vVarious kilns and furnaces.
