FDR-3571 Octane analyzer (Motor / Research Method) Scope The octane number of gasoline (petrol label) is a contract value, which means the antiknock properties of gasoline, it is the most important quality index of gasoline vehicles, it is one of the core content in oil specification analysis. It is determined by comparing with standard fuel in the standard engine test under specified operating conditions. It can conform to the ASTM D 2699, ISO 5164, ASTM D2700 standards, there are two method: Motor method and Research method. Features 1, the instrument uses a computer touch screen operation, human-friendly communication interface 2, the screen interface can display real-time experimental parameters of the indicators change, at any time monitoring 3, automatic & jog operation adjust the compression ratio, with a limit protection 4, the instrument can use two kinds of operation methods: interpolation and compression ratio method 5, the instrument can automatically generate test reports, and can automatically print the results 6, the instrument is equipped with SE air filtration system, it can provide standard, clean, dry and constant temperature gas; 7, the professional knock signal sensor FDT-DS uses the industry standard, it is more stable and reliable; 8, the instrument is equipped with a special Friend Company's knock detection system, which ensures that the knock signal of the zero, magnification, stable regulation of stability, the repeatability and precision of the instrument are less than 0.2 / R octane number. 9, it uses a magnetic induction ignition, so that the ignition time in the test is more accurate. 10, the instrument is equipped with FAD security protection system, which is used for emergency protection under abnormal conditions to protect the safety of operators; 11, the instrument uses a user-friendly design, customers can also be based on demand, self-matching low-temperature test tank and cooling water circulation system. Technical Parameters 1, measuring range: 50 to 100 octane number; 2, there are two method: Motor method and Research method, it can improve the user's investment effectiveness; 3, cylinder bore: 65mm; 4, the cylinder stroke: 100mm; 5, engine displacement: 0.33L; 6, the compression ratio range: 4: 1 to 12: 1; 7, the engine speed range: 900 ± 9r / min (Motor method) 600 ± 6r / min (Motor method) 8, the machine rated power: 8000W 9, power supply: 380 ± 10% VAC, 50 ± 1Hz 220 ± 10% VAC, 50 ± 1Hz
Item No.:Â M00302 Specification:Â 3" 4" 6" 9"
Square File Item No.: M00409 Specification: 5" 6" 8" 10" 12" 14"
Soft face hammer Item no.: m00644 Specification: 25mm 30mm 35mm 40mm 50mm 60mm
Hand riveter
We are the reputed Water Based Primer supplier and importer of MICA R-1509-C in India - Contact us now to Get a Quick quote for Water-based PEI primer for bonding PE to clay-coated surfaces in India by MICA Corporation. MICA Water- based Primers High performance, extrusion primer for inks, coatings, and adhesives. -
Carbide snow plow blade inserts 25 degree standard snowplow blade inserts 40 degree standard snow plow blade inserts Bull nose snowplow blade insert Tall bull nose snowplow blade inserts Our company manufacture many different sizes and different shapes of carbide blades for snow plough insert.HIP Sintered, excellent properties, as per the clients?requirements, at competitive prices. We can send you some pieces of samples for your testing. Please contact me for more detailed information. Thanks in advance.
Description Lodging Mechanism Description The lodging mechanism developed by my company is applicable to the communication vehicle with antenna over roof. It can control the vehicle antenna to fold and upright easily , helping the vehicle smoothly to go through the restricted road such as culvert, small group of trees, flyovers, or go into the garage, solved the communication interrupt problems led by extra high antenna which will be damaged by bumps and scrapes, improving the vehicle marching speed and operational efficiency of troops greatly. The mechanisms can be installed outside the roof of the car, control box in cab, easy operated and accurate positioning. In case the communication vehicle is out of power supply or control box does not work,the mechanism can control the antenna fold inside the vehicle or upright outside easily by a a manual wrench. Whip antenna lodging mechanism //Technical indicators 1. Working temperature: -40�C to +65�C 2. Working environment: all-weather 3. Working torque: greater than 30N.m 4. Working load: less than 3KG. 5. Power supply voltage: DC24V 6. Maximum current: less than 5A 7. Lodging speed: about 10S 8. Upright angle: 90�C more or less 0.5�C 9. Folding angle: 0�C more or less 0.5�C 10. Weight: less than 10KG 11. Reliability: failure-free more than 10 thousand times averagely.
Description Self- Leveling Systems(SLS) Description Anruier SLS is the electro-mechanical (non-hydraulic) leveling systems for recreational vehicles, special use vehicles, trailers or any mobile or stationary unit that needs leveling or stabilizing. Developed with the consumer in mind, Anruier SLS provides high performance of automatic leveling without the problems of hydraulic ones. For years weve led the way in helping people quickly and safely level and stabilize their moving platform with our SLS. We offer a complete products range of leveling systems to fit every budget. The system are consisted of three subsystem as human-computer interface, controlling system and executive mechanism. Features as follows One-Touch Auto-Leveling Steel Leveling Jacks Lead screw drive Fully Automatic Control Precise leveling less than 5 Payload from 6000kg to10000kg Easy to install and easy to use.
Quick Information Brand Name: ZhonghuiPlace of Origin: China Description Brief Description: A: Flying saw with excellent speed-tracking system is for precisely sizing cutting which can satisfy our clients�?? needs for length of finished pipe. Value Highlights: Reliable mechanical drive Precisely and effectively sizing& synchronization Endurable high-speed operation Low error rate Human-computer interfaces (HCI) with LED touch screen Manual adjustment for sizing length, tracking speed, etc B: Cold cutting saw adopts the encoder with high-resolution ratio, servo controller with high-dynamic, move-control card with high-performance, advanced error compensation technology, backlash measure and PID adjusting technology. The milling cut-off machine is with when working, , easy to operate and adjust, and Value Highlights: Produce very little heat; No the inner stress on the cutting section; No pipe mouth deformed; Length tolerance ±1mm; Smaller inner burr; SIEMENS servo motor and control system; REXROTH liner guide rail; NC control module; Full-automatic cutting;
Our carbide rods are used for cutting aluminum alloy, cast iron, stainless steel, Refractory alloy steel, nickel-based alloy, titanium alloy and nonferrous materials, For making drills, drills, end mills &reamers, mold punches, core pins&hole drilling tools.
FTTH fiber optic terminal box is mainly used in FTTH project of residential block , which provides ahighly density wall-mounting solution of optical distribution.It can be used for the splicing of drop cable ,fiber and patch cable .Environment:1. Tempreture: -40602. Ambient Humidity : 95% above 403. Air pressure: 62kPa105kPa. Feature:1. Industry standard user interface, be made of high impact plastic, PC material2. Can accommodate 1x8 & 1x16 PLC splitter3. Anti-UV, Ultra violet resistant and rainfall resistant4. Up to 16 FTTH drops5. Wall and pole mountable6. 2 inlet ports, 16 outlet ports Application1. Widely used in FTTH access network2. Telecommunication Networks3. CATV Networks4. Data communications networks5. Local Area Networks(LANs)
Dimension : 121x39x16mmSpecifications. Network Punch Down Impact Tool . A blade helps to easily remove the blocks from back mount frames . Computer tools. Network Punch Down Impact Tool . A blade helps to easily remove the blocks from back mount frames. Network Punch Down Impact Tool. Package include: 1 x Cat5 RJ11 RJ45 Network Punch Down Impact Tool.
FDR-0351 Automatic high vacuum distillation analyzer Scope This instrument is the People's Republic of China in accordance with the requirements of industry standard SH / T O165-2006 "high boiling point range of high vacuum distillation of petroleum products Determination" provides the design, manufacture, and for the determination of gas oil and lubricating oil of high boiling point range of petroleum products distillation range. Features 1, with color LCD touch screen, large screen display 2, using high-precision digital detector vacuum system, the vacuum pressure control, the pressure is more accurate 3, the instrument is often built to high standards - in terms of reduced temperature, not only to reduce the operator's labor intensity, but also make the results more accurate, more convenient and reliable data recording 4, real-time recording instrument software interface changes in temperature, volume and other parameters 5, instrument configuration printing system, automatically print test report Technical Parameters 1 Power supply: AC (220 ± 10%) V, 50Hz. 2, the flask heater power: (0 ~ 1000) W continuously adjustable. 3, receptors cylinder chamber heating power: 350W, automatic control system. 4, the cylinder chamber receptacle point temperature: room temperature ~ 99 ± 3 , continuously adjustable. 5, vacuum residual pressure setting range: (2 ~ 99) mmHg ± 0.1mmHg. 6, vacuum residual pressure measuring range: (2 ~ 150) mmHg ± 0.1mmHg, automatic constant work. 7, the buffer tank volume: 1000ml. 8, air bath lighting: energy-saving fluorescent lamps. 9, instrument conditions: Ambient temperature: (5 ~ 35) , relative humidity:
FDH-2111 Aniline point tester of petroleum products Scope Applicable standards: ISO 2977, GB / T262, ASTM D611, IP2 This instrument applies to the determination of petroleum products aniline point test method is specified aniline and sample volume placed in a test tube, and mechanical stirring to mix. The mixture is heated at a controlled rate until completely mixed the two phases. The mixture was then cooled at a controlled rate, when the two-phase separation, the temperature is recorded aniline point. Features 1, the photodetector separated state accurate; 2, high-power solid-state regulator control heating rate; 3, the voltage is raised status display; 4, integrated structure, easy to operate; 5, standard glass test tubes, meet the standard requirements; Technical Parameters 1, heating: electric heating tube 2, the mixing method: flexible shaft stirring 3, detection method: photoelectric detection 4, measurement range: room temperature ~ 150 5, power supply: AC220V 50HZ 6, temperature adjustment: a solid state voltage regulator 7, standards: ASTM D611, IP2, ISO2977, GB/T262
FDH-2171 Automatic aniline point tester of petroleum products Scope Applicable standards: ISO 2977, GB / T262, ASTM D611, IP2 The aniline point is used to characterize the pure hydrocarbon and is used to show the aromatics content of the hydrocarbon mixture. Take the same amount of aniline with the sample or sample plus n-heptane and heat and stir at the controlled rate. After the two phases are homogeneous, the mixture is cooled at the control rate, and the temperature of the two-phase re-separation is an aniline point or a mixed aniline point of the sample. Features 1, LCD display, keyboard input, equipment testing process more intuitive 2, the high degree of automation equipment, automatic detection, automatic save results 3, the use of photoelectric detection method, the results of high precision 4, the use of integrated equipment, easy operation and maintenance Technical Parameters 1. Applicable standards: in line with GB / T262 2, the test temperature: room temperature ~ 170 3. Detection: Auto photo detector 4, cooling rate: 1 / min ~ 2 / min 5 Power supply: AC220V 50HZ 6, Weight: 3KG
Hammer Psx Scrap Metal Shredder High Efficiency Scrap Metal Shredder It is scientifically designed and reasonably configured following customized schemes on customersâ??field ,output,material types and so on.It is high in automation; Monitored by computer,PLC control,safe,high-efficient,conservation of labor; Over 90% are produced by the component;quality materials are used for key components;it has exquisite techniques that are more solid and durable; All-out environmental supporting facilities on shock absorption,noise reduction and dust removal help bring down second-time pollution Remote diagnosis24 hours of uninterrupted after-sale service.
1.Introduction: Wellhead Wireline Pressure Control Equipment is used for testing and paraffin treatment in flowing oil well, gas well, water injection well and coalbed methane testing. The unit supplies buffer and transitional area for string running with pressure to hole, could satisfy the wellhead seal requirement and there is no overflow. Simple operating, safe and reliable function. Working pressure is 10MPa, 21MPa, 35MPa, 70MPa and 105MPa. Standard ID is 30mm, 52mm, 62mm (65mm), 76mm(78mm), 89mm, 102mm(103mm), 120mm, 140mm, 160mm and 180mm. Our factory has the ability to design products to adapt to different environment according to clients ' requirements. The whole Wellhead Wireline Pressure Control Equipment is composed of Grease Injection Control Head, Top Catcher, Lubricator, Bottom Catcher (include testing blowout assly), BOP, Pump-in Tee, Up sheave, Down sheave, Crossover Flange, Quick testing Assly, all kinds of pipes and other components which necessary. 2.Features and Benefits: 1.Grease Injection Control Head is operated by remote hydraulic manual pump, which could seal wellhead in time and promise safety of operation. A lube oil cup mounted on top of Grease Injection Control Head, which is as lubricator for downing cable and assistant for setting tools in well. 2.Top and Bottom Catcher is double safe feature, in order to prevent string tools dropping in well. Top Catcher is by hydraulic remote control, Bottom Catcher has manual operation system if hydraulic system is fault. There is pressure testing blowout sub, which for checking wellhead pressure, releasing left pressure in Lubricator and pressure self-check. 3.Lubricator supplies buffer and transitional area for string tools, which connected by many Union Lubricators. Single Lubricator is 0.8â??3m, the number of lubricator and total length could be decided by operation. Titanium alloy Lubricator is much better quality and lightweight than normal steel materials. 4.BOP could be separated by Single, Dual, Triple and Quad Ram. Hydraulic or Manual control. 5.There is antifreeze& unfreeze and pressure self-check system. 6.Quick testing Assly could improve the safety of BOP, then avoid the second pressure self-check. 7.Up& Down sheave is selected of Aluminium alloy, and has the function of preventing cable jump. 8.Transport and Storage Frame could accommodate full set of Pressure Control Equipments. Has the ability of designing and producing as requirements. 9.According to different service conditions, our factory supply HP/HT Wellhead Wireline Pressure Control Unit with H2S&Acid services.
Drift is a simple and general tool designed to measure inside size of casing, tubing, drill pipe and other pipes. Our Services: 1.High quality products with favorable price at right delivery. 2.Customized products. 3.Warranty. 4. When enquiry, please kindly advise below: Size: drift size & casing (tubing) spec if necessary Material: metal/ nylon or something else Quantity Port of destination if you need CNF or CIF price Your ideal delivery date if you need the goods urgently
BOP parts that we supply all come from original manufacturers, they are 100% interchangeable. BOP PART NAME: top sealing, front sealing, pipe ram, blind ram, slip ram, shear ram, spherical packer, bonnet, piston, shell. APPLY TO BELOW BOP: Brand: SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type :Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Standard: API Spec 16A,16C Working pressure:2000psi-15000psi(14 Mpa-105Mpa) Operating temperature:-18deg--121deg Bore size:7 1/16"-21 1/4" Top & nottom connection:Flanged,studded Characters: In the structure, it is divided into annular blowout preventer with spherical plastic core, annular blowout preventer with cone-shaped plastic core, and blowout preventer with tube-shaped plastic core. Annular BOP top cap and housing are connected by bolts or claw blocks. Blowout preventer with spherical plastic core and dust-proof ring. Performance characteristics: reasonable structure, easy operation, long life of plastic core, adapt to a wide range, capable to seal pipe string with nominal paths from 0-DN in ans shapes, better performance by combining with ran blowout preventer in the use. Working Principle: When wells must be sealed in case of kicks high pressure (10.5Mpa) oil from control systems enters into close-cavity under piston from housing oil outlet, to promote plastic core moving upward along ball surface, so that bearing tendons move closer to each other to moce the rubber between them to the center of wellhead so as to seal drilling tools or fully seal wellhead. In opening , hydraulic pressure oul enters into open-cavity above piston from housing oul inlet, to push piston moving downwards , so that plastic will reset with its own elasticity, wellhead will be open.
