* Conductor: 22 AWG + 26 AWG + 28AWG Strands Tinned Copper * PVC Tube: Natural color, ID: 2.4mm, OD: 4.0mm, Shore hardness: 85-90 shore A * Insulation: HDPE, Black & Brown, Red, Green & Yellow * Jacket: PVC, OD: 7.14+-0.15mm, Blue
* Conductor: 12 AWG*2C + 18 AWG*3C + 24AWG*4C Stranded Anneal Bare Copper * Insulation: SR-PVC, Red/ Black + Yellow/ White/ Gray + Green/ Blue/ Orange/ Brown All wires with tissue yarn cabling together. Foil paper to separator sheath. * Jacket: Ester polyurethane (TPU), OD: 9.5+-015mm, Matte Black.
27 AWG TC*8C PVC Microphone Cable * Conductor: 12/0.10 + #1/8 wires, Stranded Anneal Tinned Copper with Tinsel Copper * Insulation: SR-PVC, OD: 1.85+-0.05mm, Red/ White * Braid Shield: Tinned Copper with Tinsel Wire, 85% mini overall coverage 2 wire with tissue yarn filler cabling. foil paper to separators *Jacket: Soft PVC, OD: 6.8+-0.15mm, Black
Wide variety of Metal Core PCBA : Aluminum, copper or iron
Single layer, double layer or multi-layer
single-layer, double side or multi-layer
Single Side : Maximum shipping Panel Size 470mm*570mm Finished Board Thickness : Minimum Board Thickness : 0.6mm+/-0.1mm , Maximum Board Thickness : 2.0mm+/-10% Dielectric Material : Heat Conductive Glue / FR4 Aluminum Type : 5052 Copper Thickness : 1/2~2oz Trace Width / Spacing : Minimum Line Width / Spacing(Internal&External) 0.1mm ,The tolerance followed by IPC-6012 Surface Finish : Immersion Gold(Ni/Ru) 0.025~0.1um /Lead Free HASL (Min. 2.5um)/OSP (Entek CU106A) 0.2~0.5um Solder Mask : LPI Test : Hi-Pot Test
Layers: FPC 1~4 L Finished Board Thickness with Copper : Min 0.075mm (1L) / Max 0.3mm (2L) Finished Board Thickness Tolerance: �±0.02~0.04mm Impedance Control :+/-10% Base Copper Thickness : Standard : 1/3oz,1/2oz,1oz / Spcial:2oz Base Film Thickness:Standard:0.5mil , 1mil / Special : 2mil Stiffener:PI / FR-4 /SUS Finished Hole Diameter:Min { }0.15mm / Max { }6.30mm Finished Hole Diameter Tolerance PTH�±3mil(�±0.075mm) npth�±2mil(�±0.05mm)
Layers : Sample 1~32 / Mass Production 1~20 Size :Max shipping size is 600mmx550mm , +/-0.15mm Finished Board Thickness: Min 0.4mm(4L)/0.6mm(6L),+/-0.1mm (Max) 3.6mm(2.2~3.6mm depends on material), +/-10% Copper Thickness :1/3~5oz (Depends on material) Impedance Control :+/-10% Via Holes (Min) : Mechanical Drill:0.2mm / Micro Via:0.1mm PTH+/-0.075mm NPTH +/-0.05mm Aspect Ratio : Sample :10:1 / Mass Production :8:1 Min Trace(Width/Spacing) : Internal 0.075mm / External 0.075mm The tolerance followed by IPC-6012 Advance Process : Blind Routing Cavity,Coil Board,Plug Hole With Epoxy,Half Hole Plated Spacing between Pads : Min :8 mil
1. Varied battery management styles 2. 24 hours automatically monitoring 3. Wi-fi and hotspot connect method 4. High extensibility of hardware allows user to manage big amount of battery 5. B-TEK special forecast scatter chart 6. E-mail alarm notification 7. Monitoring item includes battery volt., temperature, DCR, micro-discharging volt. and EMF 8. B-TEK unique AI forecast function 9. Support Modbus TCP/IP, RTU and LAN method UPS system as the important equipment to the stable power supply needs a great amount of battery as a back-up power source. Due to the enormous amount of the batteries, it makes it hard to carry out the manual maintenance. To maintain the discharge ability during the outage, regularly manual detection is needed. However traditional battery discharge test needs battery offline. It's time-consuming and increasing the cost. BMS system can improve the risk of manual measurement, battery deterioration, and power failure, changing battery according to the actual condition of batteries. Besides, the automatic battery equalization function can extend battery life. Not only can it raise the reliability, lower the cost of battery failure, decreasing manual labor also increasing the stuff safety by avoiding direct contact with the electric device. BMU is installed to the individual battery, collecting the data and send it to the UMW to analyze. BMU is powered by the detected battery, therefore the extra power is not needed, This unit applies to a lead-acid battery, nickel-cadmium battery, lithium battery. BMU analyzes 5 parameters: terminal voltage, temperature, dc resistance, micro-discharging voltage, and electromotive force. Bu analysis, the system finds the deteriorated reasons for the battery and do the predictive maintenance. The groove on the back of BMU allows it to attach on the mounting rail. Dimension is 75*57*31mm. Reverse connection protection function will keep the internal circuit of BMU intact from a reverse connection. CMU connects to the charger and UMW. The main purpose is to monitor the current of the charger and the total voltage of the battery bank. The groove on the back of the CMU allows it to attach on the mounting rail. Dimension is 75*57*31mm.UMW provides the website browsing function, the user can access the real-time data, historical data, forecast scatter chart, line or curve graph through it. We can utilize a computer, mobile phone or tablet to remotely access the system through ethernet and hotspot function. Besides that, we can also use the FTP and VNC software to remotely access the data or control the system. When the system detects the abnormal parameter, it will automatically send the email notification and inform the users. Another AI function can provide a maximum of three years predicted data of the battery by analyzing the historical data. Efficiently manage the energy system Website: http://www.b-tek.com.tw/en/web/
EDAM-9052 8 DI and 8 DO channels Digital I/O Module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 8 isolated digital output with Open Drain. * Provide 3A/per output channel. * Provide Pulsed/delay Output Mode * Support 8 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry Contact Inputs * Fully Photo-Isolation 3750Vrms
EDAM-8530 ISO USB to RS-232 / RS-422 / RS-485 converter * Automatically switch USB signal to RS-232/RS-422 or RS-485 * Driver support for Windows 95/98/ME/2000/XP/Vista/7 * Power and activity indicator for troubleshooting * Auto switching baud rate up to 115.2 Kbps * Reserved space for termination resistors * Minimum 3000 VDC isolation protection * Mounts easily on DIN-rail or panel * Full-duplex RS-232/RS-422 support * RS-232 RTS & CTS signals support
EDAM-8520U4 Isolated RS-232 to 4-CH RS-485 converter (Iso RS-232) * True RS-485 Star Wiring Hub * Surge protection on RS-485 line * The RS-485 Short-circuit protection * Isloated on RS-232 side * Auto direction flow control on RS-485 * Independent RS-485 driver for each channel * Transmission speeds of up to 115kbps or 6 Kbps (E-8520U4F) * Power and data flow indicator for trouble shooting
EDAM-8521 Isolated Addressable RS-485/422 to RS-232 Converter * Addressable RS-485/422 to RS-232 Converter * Support Addressable or Nonaddressable mode * RS-232 support RTS, CTS handshake signal * Transmission speeds of up to 115.2 kbps * RS-232/RS-485 can be set to different baud rates * Support ASCII format and Modbus-RTU protocol * Surge protection on RS-485/422 line * Minimum 3000 VDC isolation protection * Power and data flow indicator for trouble shooting
EDAM-8531 ISO USB to RS-422 / RS-485(TX,RX,RTS,CTS) convert * Automatically switch USB signal to RS-422 or RS-485 * Driver Support For Windows 98/ME/2000/XP/Vista/W7 * Power And Activity Indicator For Troubleshooting * Auto Switching Baud Rate Up To 115.2 or 921.6 Kbps * Reserved space for termination resistors * Minimum 3000 VDC Isolation Protection * Mounts Easily On Din-Rail Or Panel * Supports RS-485 full(4-wire) / half(2-wire) duplex * RS-422 RTS & CTS Signals Support
8 Isolated Analog/Thermocouple Temperature Input Module * Support Thermocouple J.K.T.R.S.E.B.N.C Type * Protocol MODBUS RTU, ASCII Command * Support Isolated input channels * Fully photo-isolation 3750Vrms * Wide supply voltages (10-30V) * Built-in TVS / ESD protection * Burn-out auto detection
NTG-520N Pre-scored PCB Depaneling machine/ de-panelizer. Separate PCB along with V grooves. [Feature] 1. Separating the V-cut panel boards in the principle of non-bending stress. 2. The knives are adjustable both in axial and radial directions. 3. The round knives separate the board within the V-groove. Slightly adjust according to PCB thickness. 4. The depaneling maximum of PCB width is 160mm, the PCB length is unlimited. [ Specification ] Powerï¼?110V/220V, 50/60HZ Dimensionï¼?(L)430 x (W)430 x (H)520 Weightï¼?36 kgs PCB thickness rangeï¼?0.8-2.0mm www.renthang.com renthang@renthang.com
Automatic PCB Lead Cutter > > Product No. : KA-66 FEATURES Best Selection for medium of high volume production. This model is designed to trim the extra long leads automatically and efficiently on the PCB that components inserted and soldered. A pair of conveyor chain is equipped in the model in which clamp and deliver the PCB to the blade turning in high speed for trimming. Warp prevention device is equipped to ensure no damage on boards. Expandable in function and working independently- The model can be optional connecting in line with wave soldering machine by Connection Bridge and operates automatically. The Tungsten Carbide Blade is excluded in the machine. SPECIFICATIONS Dimension:900(L) x 670(W) x 800(H) m/m Power:220V 50/60HZ,Net Weight:115Kgs Feeding Speed:0 - 3 m (Adjustable) RPM of Spindle:4500 HP:3/4 HP Min. Lead Height:1.0mm Min MAX.PCB Working Size:500mm(L) x 280mm(W)
NTG350 Pre-scored PCB Depaneling machine, PCB Separator: Pneumatic Type FEATURES The machine was designed to depanel pre-scored panelboards carefully, without bending or tension stress. Even sensitive SMD-Components like ceramic capacitors, will not be damaged by the depaneling process, or thin board even to 0.3mm cab be worked safely. Due to the special design of the knives also boards with high components placed close to the edges can be depaneled safely.Based on a proven method of depaneling, wedge-shaped knives are used to cut the panels within the groove. This enables the boards less than 1mm thickness to be separated safely and without creating stress. This machine is pneumatically driven using standard parts. It is noiseless operation with none of usual compressed air noises. Rigid design without vibration in operation The PCB with sensitive SMD capacitor or thin board even to 0.3mm can be worked safely.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine. Depaneling process without vibrations Pneumatic control placed in a separate unit for easier maintenance. SPECIFICATIONS â?¢Easy maintenance and operation. Air source¡GCompressed air 5kg/cm2 Dimension¡G(L) 720 x (W) 500 x (H) 1070 mm Weight¡G190Kgs Knife length¡G350mm PCB thickness range¡G0.3mm ~ 3.0mm www.renthang.com renthang@renthang.com +886-2-82011187
Features phone Smart phone
