Definition of 400G QSFP-DD Transceivers QSFP-DD stands for Quad Small Form Factor Pluggable Double Density. The 400G QSFP-DD Transceiver follows the same port densities system as the QSFP and QSFP28, but the QSFP-DD will support eight lanes instead of four lanes for the QSFP and QSFP28, which double the density. Each of the eight lanes will operate a data rate up to 50Gb/s providing a 400Gb/s data speed and increasing the capacity of the QSFP28 by four. The 400G QSFP-DD MSA published that the size of the optical transceivers enables to put 36 ports in one switch slot, accumulating 14.4 Tbp/s in one slot. Multi-mode Transceivers Multi-mode transceivers are the low cost transceivers. QSFP-DD SR8 use more expensive non-standard MPO connectors which cancel out some of the cost savings of the multi-mode transceiver. 400G QSFP-DD SR8 The 400G QSFP-DD SR8 transceiver supports connections of up to 100 meters over multi-mode fiber and uses MPO connectors. The wavelength is 850nm. It is compliant with the QSFP-DD MSA. Single-mode Transceivers Single-Mode transceivers are more expensive than multi-mode transceivers but they allow to reach longer distance. 400G QSFP-DD DR4 The 400G QSFP-DD DR4 transceiver supports connections of up to 500 meters over single-mode fiber and uses MPO connector. The wavelengths is 1310nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD DR4+ The 400G QSFP-DD DR4+ supports connections of up to 2 kilometers over single-mode fiber and uses MPO connector. The wavelengths is 1310nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD LR4 The 400G QSFP-DD LR4 transceiver supports connections of up to 10 kilometers over single-mode fiber and uses LC connectors. The wavelengths are 1296 to 1309nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD Loopback The 400G QSFP-DD Loopback is a cost effective and high quality solutions to test 400G QSFP-DD transceivers ports.
A9500N is one of the smallest NB-IoT modules in LCC castellation packaging with the compact size of 24.0 Ã?? 26.0 Ã?? 2.3mm, ultra low power consumption and extended temperature range. Designed for use in NB-IoT network, A9500N enables connect to the Internet at DL and UL data speed up to 200kbps. In the area where NB-IoT service are not available, A9500N still enables reliable and secure data connect over EGPRS network. To save space on the application platform, A9500N comes as an extremely slim and compact module. This makes it ideally suited for a broad range of mobile computing devices, and particularly offers easy integration with AMI, Security, Intelligent Buildings and other M2M application. General features * NB-IoT Tri-bandB3/B5/B8 * EGPRS Dual-bandB5/B8 * Control via AT commands(GSM07.05,GSM07.07,V.25TER,GPRS, and enhanced AT commands) * Supply voltage range 3.1V-4.2V * Low Power consumption - eDRX mode:
The SIM7000C is Multi-Band LTE-TDD/LTE-FDD and Dual-Band GSM/GPRS/EDGE module solution in a SMT type which supports LTE CAT M1(eMTC) and NB-IoT up to 375kbps for downlink data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, GPIO etc. the module provides much flexibility and ease of integration for customer's application. The biggest advantage of the product is low power consumption. General features * Single-Band TDD-LTE B39 * Three-Band FDD-LTE B3/B5/B8 * GSM/GPRS/EDGE 900/1800 MHz * Control Via AT Commands * Supply voltage range: 3.4V~ 4.2V, Typ:3.8V * Operation temperature: -40â?? to +85â?? * Dimension: 24*24*2.6 mm * Weight: 3.0g * GNSS Specifications for Data transfer * LTE CAT M1 - Uplink up to 375kbps, - Downlink up to 375kbps * NB-IoT - Uplink up to 72kbps, - Downlink up to 32kbps * EDGE Class - Max. 236.8Kbps(DL/UL) * GPRS - Max. 85.6Kbps(DL/UL) Other features * USB Driver for Microsoft Windows2000/XP/Vista/Win7/Win8/Win10 * USB Driver for Windows CE/Mobile * USB Driver for Linux /Android * RIL supporting for Android/WindowsCE/Mobile * Firmware update via USB * TCP/IP/IPV4/V6 Multi-PDP,MT PDP * DTMF* * Gobi SDK to the Win7/Win8/Linux * MBIM to Win8 * Source code of the PC manager of the device for reference Interfaces * USB2.0 * UART * SIM card * GPIO * ADC * PCM*
The SIM7000E is Tri-Band LTE-FDD and Dual-Band GPRS/EDGE module solution in a SMT type which supports LTE CAT-M1(eMTC) and NB-IoT up to 375kbps data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, GPIO etc. The module provides much flexibility and ease of integration for customer's application. The package of SIM7000E is compatible with SIM900 and SIM800F. AT commands of SIM7000E are mostly compatible with SIM800F. This also maximizes the investments of customers, and enables a short time-to-market. It is designed for applications that need low latency, medium throughput data communication in a variety of radio propagation conditions. Due to the unique combination of performance, security and flexibility, this module is ideally suited for M2M applications, such as metering, telematics, asset tracking, remote monitoring ,E-health , mobile pos terminals and sharing bike. General features * Tri-Band FDD-LTE B3/B8/B20 * GPRS/EDGE 900/1800Mhz * Output power - GSM900: 2W - DCS1800: 1W * Control Via AT Commands * Supply voltage range: 3.0V~ 4.3V, Typ: 3.8V * Operation temperature: -40â?? to +85â?? * Dimensions: 24 X 24 X 2.6mm * Weight: 3.0g * GNSS (GPS,GLONASS and BeiDou/Compass, Galileo, QZSS) Specifications for Data transfer * LTE CAT-M1(eMTC) - Uplink up to 375kbps, Downlink up to 300kbps * NB-IoT - Uplink up to 66kbps, Downlink up to 34kbps * EDGE Class - Uplink up to 236.8Kbps, Downlink up to 236.8Kbps * GPRS - Uplink up to 85.6Kbps, Downlink up to 85.6Kbps Other features * USB Driver for Microsoft Windows XP/Vista/7/8 * USB Driver for Windows CE/Mobile * USB Driver for Linux/Android * Firmware update via USB * TCP/IP * PPP * SMS * EMAIL * FTP/HTTP/SSL * VoLTE* * FOTA* Interfaces * USB2.0 x1 (high-speed) * UART x2 (7-wire UART and 2-wire UART interface multiplex from GPIO) * SIM card x1 (1.8V and 3V) * I2C x1 * GPIO x5 * ADC x1 Consumption * Power off: 7uA * PSM: 9uA * Sleep: 1mA * Idle: 11mA
4G with SIM card holder is a wireless module which is designed for the global market. It is a consumptive product; It can be designed in many kinds of applications which can work on LTE-FDD/UMTS/GSM/GPS/GLONASS(Optional) network. On LTE-FDD network, 4G with SIM card holder enables connect to the Internet at DL data speed up to 150Mbps and UL data speed up to 50Mbps. In the area where LTE service are not available, 4G with SIM card holder still enables reliable and secure data connect over 3G(UMTS) or 2G(GSM) network. 4G with SIM card holder provides SMS, MMS, Phonebook functions as well as high speed access, and also audio function. It can be designed in many kinds of applications. Such as Data card, Video monitor, Tablet, Electric-book, MID, Vehicle equipment, etc. General features: EDGE multi-slot class 33 GPRS multi-slot class 33 Compliant to GSM phase 2/2+ Output power: - Class 3 (0.25W) for LTE/UMTS - Class 4 (2 W) for GSM 900 - Class 1 (1 W) for GSM 1800 Control via AT commands (3GPP TS27.005/3GPP TS27.007 ) Supply voltage range 3.3V- 4.2V Low Power consumption - Sleep mode: 3mA - Power down: 16 �¼A Dimensions: 51.0�?30.0�?4.6mm Operation Temperature: -40�°C to +85�°C MSL : 3 Band Configuration LTE-FDD Band 1/3/5/7/8/20/28 LTE-TDD Band 38/40 UMTS Band 1/5/8 GSM Band 3/8 Specifications for GNSS GPS frequency: 1575.42MHz At least support 44 channels Sensitivity - Acquisition: -158dBm - Tracking: -162dBm TTFF - Cold Start: 28s - Warm Start: 18s - Hot Start: 1s Specifications for data Support Release 11 Category 4 LTE-FDD up to 150 Mbps DL,50 Mbps UL LTE-TDD up to 130 Mbps DL,35 Mbps UL DC-HSPA+ up to 42.2Mbps DL,5.76Mbps UL EDGE class 33: 296Kbps DL,236.8Kbps UL GPRS class 33: 107kbps DL,85.6kbps UL CSD up to 14.4 kbps Non transparent mode PBCCH support PPP-stack Coding schemes CS 1,2,3,4 FOTA TCP/IP NDIS Specifications for SMS Point-to-point Mo and MT SMS cell broadcast Text and PDU mode Protocols TCP/ UDP/ PPP/ FTP/ HTTP/ HTTPS/ SMTP*/ SMTPS*/ MMS/ FTPS*/ NTP/ PING/ QMI/ SSL/ NITZ/ CMUX/ MQTT* Additional features VoLTE Phone book PCM DTMF Interfaces: RF connector PCI Express�® Mini Card Interface - Power supply - USB 2.0 high speed - UICC/SIM/UIM card interface 3V, 1.8V - UART - Analog Audio - PCM Antenna connector SIM Card Holder Approvals: RoHS / CE / GCF / RCM / NCC
SIM7600X-H-PCIE is a complete multi-band LTE-FDD/LTE TDD/HSPA+/UMTS/EDGE/GPRS/GSM module solution in Mini PCIE type which supports LTE CAT4 up to 150Mbps for downlink and 50Mbps for uplink data transfer.It is combined with a SIM7600X-H (LCC) module and a Mini PCIE adapter board. Target market: EMEA/Korea/Thailand SIM7600E-H-PCIE * Support 4G LTE FDD Band B1/B3/B5/B7/B8/B20 and TDD Band B38/B40/B41 * Support 3G UMTS/HSPA+ B1/B5/B8 * Support 2G GSM/GPRS/EDGE B3/B8 * GSM/GPRS/EDGEB3/B8 General features * Mini PCIE package * Control Via AT Commands * Supply voltage range: 3.0V~ 3.6V, 3.3V Typical * Operation temperature: -40â??to +85â?? * Bandwidth: 1.4/3/5/10/15/20MHz * 3GPP E-UTRA Release 11 * Dimensions: 50.8*31*5.35mm * Weight: 12.6g Specifications for Data transfer * LTE Downlink up to 150Mbps, Uplink up to 50Mbps * HSPA+ Downlink up to 42Mbps, Uplink up to 5.76Mbps * WCDMA Downlink/Uplink up to 384Kbps * EDGE Downlink/Uplink up to 236.8Kbps * GPRS Downlink/Uplink up to 85.6Kbps Other features * USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win8/Win10 * USB Driver for Linux /Android * RIL supporting for Android 2.4/4.0/5.0/6.0/7.0 * MBIM to Win8 * Firmware update via USB * TCP/IP/IPV4/IPV6/Multi-PDP/FTP/FTPS/HTTP/HTTPS/SMTP/SMTPS/DNS * SSL3.0/TLS1.0/TLS1.2 * DTMF (Sending and Receiving) * Audio Playing * USB Audio and VoLTE * FOTA * eCall* Interfaces * USB2.0 with High speed up to 480Mbps * UART * GPIO * Antenna: Solder pads for Primary, Rx-diversity and GNSS antennas * (U)SIM card (1.8V/3.0V) * Digital Audio through PCM * Analog Audio (Optional) * Embedded SIM card socket (Optional) * GNSS: GPS/GLONASS/Beidou/Galileo*
30 AWG 5C PU SpO2 Cable, OD: 4.2 ± 0.15 * Conductor: 30 AWG 24/0.05 + Stranded Plated silver alloy copper + 200d Kevlar yarn * Insulation: PP, OD: 0.65 �± 0.05 * Twist pair + shielded: 2 wire with filler cabling and spiral shielded (45+-3/0.08Tinned copper + 0.02mm /#1 Tinsel copper), 85% coverage * Inner sheath: PVC white color, OD: 1.9+ -0.1mm * Braid shielded: Tinned copper, 16/7/0 .08TC braid shielded 85% coverage * Jacket: PUR, OD: 4.2 ± 0.15 (Matte gray)
26 AWG DC Power Wire * Conductor: Stranded Bare Copper, OD: 0.12±0.03 mm * Insulation: SR-PVC + PP, OD: 1.0±0.04 mm * Jacket: Medical Grade PVC, OD: 3.0±0.1 mm
18 AWG 4C Mechanical Cable * Conductor: Anneal Stranded Bare Copper, OD: 0.08+-0.004mm * Insulation: Polypropylene, OD: 2.4+-0.08mm, Black Brown Blue and (Yellow with green stripe) * Braid shield: Anneal Tinned Copper, 90% mini overall coverage. All wires with tissue yarn cabling together and foil paper to separator braid * Jacket: Migration and Oil Resistance PVC, OD: 9.0+-0.2mm, Matte Black Color Cable mark: ROBOT-TOP 300V 0.75mm �² 150 / 0.08x 4C (oil, shake, flame and bend resistant with white ink)
* Inner Cable: Coaxial Cable + 24 AWG*2C(RD/ BK) + 28 AWG*16C * Jacket: PUR (Black, OD: 5.8+-0.1 mm ) * Coaxial Cable: PUR (OD: 2.45mm, Impedanc: 50+-2 ohm) * Rated Temperature : -40 C ~ +80 C
* Conductor: 22 AWG + 26 AWG + 28AWG Strands Tinned Copper * PVC Tube: Natural color, ID: 2.4mm, OD: 4.0mm, Shore hardness: 85-90 shore A * Insulation: HDPE, Black & Brown, Red, Green & Yellow * Jacket: PVC, OD: 7.14+-0.15mm, Blue
* Conductor: 12 AWG*2C + 18 AWG*3C + 24AWG*4C Stranded Anneal Bare Copper * Insulation: SR-PVC, Red/ Black + Yellow/ White/ Gray + Green/ Blue/ Orange/ Brown All wires with tissue yarn cabling together. Foil paper to separator sheath. * Jacket: Ester polyurethane (TPU), OD: 9.5+-015mm, Matte Black.
*Material: ABS (Acrylonitrile Butadiene Styrene) *OD: 1.75 +/- 0.05 mm *Net Weight: 1 kg *Material Supplier: CHI MEI CORPORATION POLYLAC
Features â?? RJ45 unshielded plug â?? ISO/IEC 11801,ANSI/TIA 568 C.2) â?? IEEE 802.3af /at / bt â?? Suitable for 23~26AWG, stranded and solid wire â?? Cable outer diameter: 4.5~7.2mm â?? Easy, quickly, reliable and comfortable installation â?? Suitable for cabling from home networks to large data centers
1. Varied battery management styles 2. 24 hours automatically monitoring 3. Wi-fi and hotspot connect method 4. High extensibility of hardware allows user to manage big amount of battery 5. B-TEK special forecast scatter chart 6. E-mail alarm notification 7. Monitoring item includes battery volt., temperature, DCR, micro-discharging volt. and EMF 8. B-TEK unique AI forecast function 9. Support Modbus TCP/IP, RTU and LAN method UPS system as the important equipment to the stable power supply needs a great amount of battery as a back-up power source. Due to the enormous amount of the batteries, it makes it hard to carry out the manual maintenance. To maintain the discharge ability during the outage, regularly manual detection is needed. However traditional battery discharge test needs battery offline. It's time-consuming and increasing the cost. BMS system can improve the risk of manual measurement, battery deterioration, and power failure, changing battery according to the actual condition of batteries. Besides, the automatic battery equalization function can extend battery life. Not only can it raise the reliability, lower the cost of battery failure, decreasing manual labor also increasing the stuff safety by avoiding direct contact with the electric device. BMU is installed to the individual battery, collecting the data and send it to the UMW to analyze. BMU is powered by the detected battery, therefore the extra power is not needed, This unit applies to a lead-acid battery, nickel-cadmium battery, lithium battery. BMU analyzes 5 parameters: terminal voltage, temperature, dc resistance, micro-discharging voltage, and electromotive force. Bu analysis, the system finds the deteriorated reasons for the battery and do the predictive maintenance. The groove on the back of BMU allows it to attach on the mounting rail. Dimension is 75*57*31mm. Reverse connection protection function will keep the internal circuit of BMU intact from a reverse connection. CMU connects to the charger and UMW. The main purpose is to monitor the current of the charger and the total voltage of the battery bank. The groove on the back of the CMU allows it to attach on the mounting rail. Dimension is 75*57*31mm.UMW provides the website browsing function, the user can access the real-time data, historical data, forecast scatter chart, line or curve graph through it. We can utilize a computer, mobile phone or tablet to remotely access the system through ethernet and hotspot function. Besides that, we can also use the FTP and VNC software to remotely access the data or control the system. When the system detects the abnormal parameter, it will automatically send the email notification and inform the users. Another AI function can provide a maximum of three years predicted data of the battery by analyzing the historical data. Efficiently manage the energy system Website: http://www.b-tek.com.tw/en/web/
8 Isolated digital input and 3 relay output * Support 8 isolated digital input channels * Input channel support max. 50Hz counter * Support 3 relay output channels (Form A) * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
EDAM-9052 8 DI and 8 DO channels Digital I/O Module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 8 isolated digital output with Open Drain. * Provide 3A/per output channel. * Provide Pulsed/delay Output Mode * Support 8 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry Contact Inputs * Fully Photo-Isolation 3750Vrms
EDAM-9060A 5-channel Digital Input and 3 RELAY Output module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 3 relay ch. (RL1/Form A,RL2/3 Form C) * Provide Pulsed/delay Output Mode * Support 5 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry/ Wet Contact Inputs * Fully Photo-Isolation 3750Vrms * Status LED indicator
EDAM-8067D 8-ch relay(0.5A/120Vac, 1.0A/24Vdc) Output module with LED display * 8-Channels relay Output * Normal Open Relay Output(Form A) * Relay contact rating 5A/120Vac,1A/24Vdc. * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS RTU And ASCII Format
EDAM-8530 ISO USB to RS-232 / RS-422 / RS-485 converter * Automatically switch USB signal to RS-232/RS-422 or RS-485 * Driver support for Windows 95/98/ME/2000/XP/Vista/7 * Power and activity indicator for troubleshooting * Auto switching baud rate up to 115.2 Kbps * Reserved space for termination resistors * Minimum 3000 VDC isolation protection * Mounts easily on DIN-rail or panel * Full-duplex RS-232/RS-422 support * RS-232 RTS & CTS signals support
