Properties: Gray white powder (granule). The density is 1.26-1.32. soluble in benzene, CS2, methyl alcohol, acetone. chloroform, alcohol, insoluble in gasoline, water, acid and alkali with lower concentration. Application: Provides fast cure rate and high modulus development in NR, SBR, BR and blends. Normally used alone or with small quantities of ultra accelerators in tire compounds or industrial rubber products low poison and high efficiency. It is good back up for NOBS. Be regarded as standard accelerator. Packaging: 25kg plastic woven bag, paper with plastic film bag, kraft paper bag or jumbo bag. Storage: The product should be stored in the dry and cooling place with good ventilation, avoiding exposure of the packaged product to direct sunlight. The validity is 1 year.
Properties: White powder (granule). Density is 1.41. Soluble in 1% NaOH solution, CS2, benzene, chloroform, slightly soluble in alcohol, insoluble in gasoline. Application: Used for NR, IR, SR, SBR, NBR, EPDM and their latexes. A fast curing primary or secondary effective ultra-accelerator for natural and synthetic latex form compounds. Can be used advantageously for dipped, spread, and cast goods. Similar in property that of PZ. Less resistance to scorching than PZ and shows a slight tendency to premature vulcanization. An antioxidant in adhesive systems. Packaging: 25kg plastic woven bag, paper with plastic film bag, kraft paper bag. Storage: The product should be stored in the dry and cooling place with good ventilation, avoiding exposure of the packaged product to direct sunlight. The validity is 2 years.
Properties: White powder (granule). No taste, no poison. Density is 1.66. Soluble in lower concentration alkali, CS2, benzene, acetone and CH2Cl2, partly soluble in chloroform, insoluble in alcohol, CCl4 and ethyl acetate. Application: Used for NR, IR, BR, SBR, NBR, HR, EPDM and natural & synthetic latexes. Stronger accelerating power than TMTD. Strong resistance to scorching. In its handling, care should be operated, because of its increase activation and strong tendency to scorch at low temperatures (100?C). Often used as a secondary accelerator. In latex, better results are obtained when used in combination with other types such as thiazole accelerators. Used for rubber coated fabrics, latex products and rubber cement, etc. FDA approved in USA. Packaging: 25kg plastic woven bag, paper with plastic film bag, kraft paper bag. Storage: The product should be stored in the dry and cooling place with good ventilation,avoiding exposure of the packaged product to direct sunlight. The validity is 2 years.
Product description Model no: jsj95/200 The first stage l/d ratio: 32:1 The second stage l/d ratio: 9:1 Price: 136666 usd/set The first stage power:260kw The second stage power:80kw Screw diameter: 92/200 Screw speed: 500/85 Capacity: 1000-1200kg/h Packing: wood case or according to requirement Certification: sgs, ce Features: 1.Low maintenance, robustness, durable finish standards, excellent functionality 2.High-efficient force-feeder ensures high capacity feeding, low energy consumption 3. Our machine has two characteristics: high degree of automation and assembly line work. 4.The pelleting machine has good dispersion effect. 5.The machine production is very high, and the work environment is very clean. 6.The technology can be adjusted according to customer's raw material. Type Diameter(mm) L/d Screw speed(r/min) Motor power (kw) Capacity(kg/h) Jsj52/100 50.5 28-40:1 500 45 150-250 100 7-12:1 85 37 Jsj65/150 62.4 28-40:1 500 55-75 500-700 150 7-12:1 85 45-55 Jsj75/180 71 28-40:1 500 90-110 750-900 180 7-12:1 85 55-75 Jsj95/200 92 28-40:1 400-500 250-315 1000-1200 200 7-12:1 85 75-90
Product description Model no: js75b Price: 52666 usd/set High speed machine: 500l Twin single motor diameter: 71mm Main motor power: 132kw Weight: 29.8t Extrusino width: 1800mm Extrusion thickness: 0.8-6mm Capacity: 450-750kg/h Screw l/d ratio: 32-64 Diameter: 71mm Screw rotating speed: 600rpm/min Main motor power: 110-132-160kw Screw torque: 995n.M Torque rating: 4.6t/a2 Packing: wood case or according to requirement Certification: sgs, ce Features: 1.Low maintenance, robustness, durable finish standards, excellent functionality 2.High-efficient force-feeder ensures high capacity feeding, low energy consumption 3. Our machine has two characteristics: high degree of automation and assembly line work. 4.The pelleting machine has good dispersion effect. 5.The machine production is very high, and the work environment is very clean. 6.The technology can be adjusted according to customer's raw material. Model Volume Screw diameter Main motor(kw) Weight T Width mm Thicknessmm Capacity (kg/h) Js65b 300l 62.4mm 75 =19.5 =1000 0.8-6 200~320 Js75b 500l 71mm 132 =29.8 =1800 350~680 Js95b 800l 91mm 185 =39.4 =2150 800~1100
Properties: Gray-white powder (granule) with a little odor, no poison. The density is 1.31-1.34. Soluble in benzene,boluene, chloroform, CS2, CH2Cl2 acetone, ethyl acetate, hardly soluble in alcohol, insoluble in water,gasoline, acid / alkali with lower concentration. Application: A medium fast primary accelerator suitable for NR, IR, SBR, NBR, HR and EPDM. An outstanding delayed action accelerator. Be top effective and safe when used at ordinary processing temperatures, causing no scorches. Vulcanized show excellent physical property and quick complete. Usually used alone when activated by DPG, TMTD and TS. Packaging: 25kg plastic woven bag, paper with plastic film bag, kraft paper bag or jumbo bag Storage: The product should be stored in the dry and cooling place with good ventilation, avoiding exposure of the packaged product to direct sunlight. The validity is 1 year.
RSS3/SVR10/SVR3L NEW PRICE, HIGH QUALITY. - origin: vietnam - color: brown - quality: according to standard vietnamese rubber - supply ability: 2, 000 mt/month Pexim JSC always supply high quality products, we have never ever made our customers disappointed. Contact us for a perfect long term business:
RSS3/SVR10/SVR3L NEW PRICE, HIGH QUALITY. - quality: grade a, according to standard vietnamese rubber - supply ability: 2, 000 mt/month - color: bright yellow Pexim JSC always supply high quality products, we have never ever made our customers disappointed. Contact us for a perfect long term business:
* Description SVR 10 SVR 10 is made from field coagulum materials. The materials are precleaned by passing them through creper – hammermills and then stored some weeks for maturation before production. Mature materials are blended and soaked in the water to be clean, size reduction to crumbs, drying and baling. SVR 10 has good technological properties similar to SVR 20, but lower dirt content * Used for the manufacturing -Passenger tyres -Truck tyres, -Motorcycle and bicycle tyres -Inner tubes -Conveyor belts -Footwear. * Features Low rolling resistance. • Low endogenous heat. • High resistance to cutting • High resistance to tearing * Specification Dirt : 0.08 max Ash : 0.60 max Volatile Matter: 0.80 max Nitrogen : 0.60 max Initial Wallace plasticity (Po): 30 min Plasticity Retention Index (PRI) : 50 min *At time of production, ML 1+ 4 (100 oC) * Packing • 33.33 kg/bales or 35kg/bales, 600 bales/fcl 20 feet • In loose bale or Wooden Pallet * Bale Packaging • Normal 0.03 mm PE bag wrapper with melting temperature under 109 oC. • Thick (0.13 mm) PE bag wrapper
* Description SVR 5 SVR 5 is a quality natural rubber. It is produced wholly from field latex. Field latex is preserved with ammonia or sodium sulfite. This is type of rubber which production process is the same SVR 3L grade. The field latex is coagulated with formic acid, and then make crumbs by passing through a crusher, some crepers and a shredder. After the dried crumbs are cooled and then compressed into blocks. * Used for The Manufacturing -Bicycle tubes -Rubber threads -Gas masks -Components in passenger vehicles -Components in tires * Features • Dark color than coloured SVR 3L. • Higher ash and dirt content compare with SVR 3L • High tensile strength • Good heat ageing resistance. * Specification Dirt : 0.05 max Ash : 0.60 max Volatile Matter: 0.80 max Nitrogen : 0.60 max Initial Wallace plasticity (Po): 30 min Plasticity Retention Index (PRI) : 60 min Color (Lovibond): 6 max *At time of production, ML 1+ 4 (100 oC) * Packing • 33.33 kg/bales or 35kg/bales, 600 bales/fcl 20 feet • In loose bale or Wooden Pallet * Bale Packaging • Normal 0.03 mm PE bag wrapper with melting temperature under 109 oC. • Thick (0.13 mm) PE bag wrapper
* Description SVR 10CV is produced from cuplumps. it has constant viscosity by added with only hydroxylamine neutral sulfate (HNS). It is produced through the two dryprebreakers equipment and cool processing line. This is a grade of rubber with constant viscosity. The hydroxylamine substance inhibits the storage hardening reaction in natural rubber, which leads to an increase in its Mooney viscosity. * End Use -Anti-vibration mounting products -Metal bonding -Low density sponge -Rubber–metal bonded components -Industrial rolls -Special mechanical goods. * Features • Constant viscosity rubber • Softer than technically standard other grades • Homogenous viscosity * Specification Parameters Unit Limit Test Methods Dirt (retained on 45 micron aperture) % wt 0.16 max TCVN 6089:2004 ISO249:1995 Ash % wt 0.60 max TCVN 6087:2010 ISO247:2006 Volatile Matter % wt 0.80 max TCVN 6088:2010 ISO248:2005 Nitrogen % wt 0.60 max TCVN 6091:2004 ISO1656:1996 Initial Wallace plasticity (Po) - - TCVN 8493:2010 ISO 2007:2007 Plasticity Retention Index (PRI) % 50 min TCVN 8494:2010 ISO 2930:2009 Mooney Viscosity MU 60(+7, -5) TCVN 6090-1:2010 ISO 289-1:2005 *At time of production, ML 1+ 4 (100 oC) * Packing • 33.33 kg/bales or 35kg/bales, 600 bales/fcl 20 feet • In loose bale or Wooden Pallet * Bale Packaging • Normal 0.03 mm PE bag wrapper with melting temperature under 109 oC. • Thick (0.13 mm) PE bag wrapper
* Description SVR CV50 is a constant viscosity grade. It is made by adding hydroxylamine neutral sulfate (HNS) and peptizer before coagulation with acid. The coagulum is allowed to mature some hours, reduced to crumbs by passing through a crusher, crepers, a shredder, dried and pressed into bales. The hydroxylamine inhibits the storage hardening reaction in natural rubber, which leads to an increase in its Mooney viscosity. Mooney vicosity (MV) is 50 ± 5. * Used For The Manufacturing -Vibration mountings for engines and machinery -Railway buffers -bridge bearings -Automotive components -Large-truck tire treads -Conveyor belt covers -Masking tapes -Rubber–metal bonded components * Features • Low viscosity rubber • Softness * Specification Dirt : 0.02 max Ash : 0.40 max Volatile Matter: 0.80 max Nitrogen : 0.60 max Plasticity Retention Index (PRI) : 60 min Mooney Viscosity MU 50 ± 5 *At time of production, ML 1+ 4 (100 oC) * Packing • 33.33 kg/bales or 35kg/bales, 600 bales/fcl 20 feet • In loose bale or Wooden Pallet * Bale Packaging • Normal 0.03 mm PE bag wrapper with melting temperature under 109 oC. • Thick (0.13 mm) PE bag wrapper
* Description SVR CV 60 is a constant viscosity grade. It is made by only adding hydroxylamine neutral sulfate (HNS) to ammonia preserved field latex after reception at factory. HNS is only added before coagulation with acid. The SVR CV60 rubber is processed through some stages such as crushing, creping, crumbing, drying and baling. The hydroxylamine inhibits the storage hardening reaction in natural rubber, which leads to an increase in its Mooney viscosity. Mooney viscosity (MV) is 60 ± 5. * Used For The Manufacturing -Anti-vibration mountings -Conveyor belts -Rubber and metal bonded components -Injection moulded products -Extruded products -Masking tapes -Railway buffers -Automotive components -Rubber–metal bonded components * Features • A constant viscosity rubber which hasn’t used peptizer agent . • • Constant Mooney viscosity, cleanliness, uniformity, and softness. * Specification Dirt : 0.02 max Ash : 0.40 max Volatile Matter: 0.80 max Nitrogen : 0.60 max Initial Wallace plasticity (Po) - Plasticity Retention Index (PRI) : 60 min Mooney Viscosity MU: 60 ± 5 **At time of production, ML 1+ 4 (100 oC). Viscosity limit can be based on customers’ requirement. * Packing • 33.33 kg/bales or 35kg/bales, 600 bales/fcl 20 feet • In loose bale or Wooden Pallet * Bale Packaging • Normal 0.03 mm PE bag wrapper with melting temperature under 109 oC. • Thick (0.13 mm) PE bag wrapper
Extruder:EPDM sheet extrusion machine,EVA interior sheet extruder,Rubber sheet extrusion machine,such as rubber and plastic sheet extrusion machine. Features: 1.The characteristics of the machine is advanced design, high quality, good plasticizing and low energy consumption. 2.It has the advantages of low noise, smooth operation, large loading and long life. 3.The technology can be adjusted according to customer’s raw material.
Properties: A high activity antioxidant for matural and synthetic rubber provides powerful antiozonant and antioxidant properties with excellent high temperature, fatigue and flex resistance to rubber compounds. While used primarily for ozone resistance, it is a more active antioxidant than quinoline or diphenylamine based antioxidants. The product (alone or in combination with TMQ) provides compound protection against catalytic degradation by copper and other heavy metals. The product has no negative effects on compound adhesion to textiles or steel cord up to levels of 2 phr. Above this concentration it may bloom and interfere with ply to ply and ply to cord adhesion. It will discolor compounds and cause severe contact and migration staining. Application: Used in pneumatic tire components, solid tires, belts, hoses, cables, automotive mounts, bushings and general mechanical products that are exposed to continuous and intermittent dynamic operating conditions and require protection from ozonation. Package: 25kg N.W./bag, in plastic fabric laminated kraft bags lined with plastic bags. Storage: Store closed containers in a cool, dry, well-ventilated area, store far from strong oxidizing materials. Avoid exposure to direct sunlight. Do not double stack.
NAME: High Temperature Stable Insoluble Sulfur IS-HS Series Standard: Q/IMFJ 001-1997 Use: Sulfur vulcanizer improves high temperature safety in rubber masticating without frosting and burnt rubber and improves binding of rubber-rubber and rubber-steel or chemical fiber without contaminating mold. Widely used in natural and synthetic rubber in manufacturing tire, rubber tube, rubber belt, rubber shoes, rubber roller, cabel, seal, latex products and light color rubber products. Packaging: 25kg in plastic woven bag lined with PVC film. Storage: keep in dry, cool and ventilated place with temperature
Pad printing silicone rubber is mainly applicable to the printing of irregular patterns on plastics toys, electroplating products, electronic, trademarks, artwork gifts, and stationary, etc. And the silicone pad is a carrier which transfers the patterns from the steel plate onto the products’ surface, it has the advantage of good printing effects, good quality, good resilience and without any impurity. Operation method of the pad printing silicone rubbuer. 1. Firstly, you should prepare all the tools such as the pad mold, the cup for mixing, and a glass stick. 2. Then clean the pad mould with detergent, and dry it with a piece of cloth or an air gun. 3. After that, mix the pad printing silicone rubber and the silicone soil as your own requirements. Generally, the larger the size of the pattern you need to print, the more silicone oil is needed. FAQ of the pad printing silicone oil: 1.Why we should add silicon oil into pad printing silicon? Customers should change the hardness of the silicone pad according different patterns, silicone oil can change the hardness and the viscosity of the liquid silicone oil.
Trade name: MBT,M Chemical Name : 2-Mercaptobenzothiazole Molecular Formula: C7H5NS2 Item Specifications Appearance: Light-yellow powder Initial M.P.,?= ,170.0 Loss on Drying%,= , 0.4 Ash%,= , 0.30 (150µm)Residues %,=, 0.05
Trade name: MBTS,DM Chemical Name: Dibenzothiazole disulfide Molecular Formula: C14H8N2S4 Used as an acid accelerator currently and a medium fast primary accelerator. Imparts excellent aging properties when used both alone and in combination with DM, TMTD and many other basic accelerators for higher activity. Its accelerative temperature is low and easily be dispersed with lower pollution. Mainly used in the manufacture of tires, tubes, foot wear, rubber belts and hoses etc.
Product Description Rubber floor tile vulcanizing press machine 1- Name: Rubber Vulcanizing Press, Plate Rubber Vulcanizer, Plate Rubber Vulcanizing machine, Rubber Vulcanizing Machine, Vulcanizer, Lab vulcanizing press, Rubber hydraulic press, Plate curing press, Rubber vulcanizing machine, Rubber vulcanizing machinery. 2-Use: This vulcanizing machine is used for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products. 3-Main Features: A.Being a column structure and downward pressing type, the heating plate opens by the self-weight of the heating plate, platform and plunger. The rising of the plunger makes the heating plate close while the hydraulic oil provides the pressure. B.The engine base is combined together with the cylinder and base frame, which is made of ductile iron to increase the cylinder intensity and a brad ability. The cylinder is fitted with the sealing washer made of the oil-resisting rubber for the sealing purpose. C.By moving the operational handle of the control valve to the two different positions, the heating plate can open and close. D.It uses the electric pipe for heating, thus makes the workshop clean with easy and reliable operation. Packing: Exporting standard(wooden box packing) Delivery time: 30 days after receipt deposit Payment Term: TT 30% deposit 70% balance payable within 3 days once received the copy of shipping docs(CI,PL&BL) Or L/C at sight with irrevocable
