Round Dot Rubber Sheet Specification: Long: 10m/15m/20m Wide: 1-1.6m Thickness: 3-8mm Color: Red, green, gray, blue, black Density: 1.5g/cm3 Tensile strength (Mpa): 3 Shore scleroscope hardness A: 655 Application: Entrances reception area doorways corridors Hallways Features: anti-slip design which reduces the chance of people falling over impact absorbing and hardwearing which ensures cushioning under foot available in long lengths which avoids joins and trip points easy to clean patterns open design pattern which provides a good grip and is easy to clean available in long lengths for minimal joins soft, yet hard wearing which provides both comfort and durability non porous surface which is easy to clean and avoids a build up of bacteria We produce rubber sheet flooring include stud round dot rubber roll, fine ribbed, checker plate, willow, board ribber rubber sheet with anti slip feature.
Cloth Insertion Rubber Sheet Specification: Long: 10m-20m Wide: 1-2m Thickness: 1-20mm Color: black Material: Recycled rubber granuleswith Cloth Insertion Density: 1.1-1.6g/cm3 Tensile strength (Mpa): 3 Shore scleroscope hardness A: 655 Application: Usedin air, hot water, saturated steam, low pressure steam, and hydraulic services. Features: Add stability 1-2 ply cotton cloth and EP cloth can be choosing We wholesale cloth insertion rubber sheet, insert nylon, nbr, foamed, silicone, board ribber rubber sheet and mat. New Cattle Mat
HNBR rubber bladder is composed of rubber pulsation bladder,rubber balance plate and pressure plate bolt, it can reduce the drilling pump pressure fluctuations of instantaneous displacement change; Make the pump pressure smoothly, protect equipment from damage caused by severe vibration. the product is also used as stabilizer and vibration absorber for air pump. Filled with nitrogen in the air or inert gas, in the absence of them,air can replace.But oxygen or combustible gas is forbidden. Inflation pressure is 20% ~ 30% of the maximum working pressure. The advanced filling pressure is 2.0-2.5 MPa.
Natural rubber for conveyor belt Natural rubber for automobile part Natural rubber for another rubber finishing product
O" Ring(40169320) ,Oil Seal(40169330), Gasket,Bucket(40169340), Washer(40169350), Bush,Rubber pad(40169960), Bellow(40169990),Rubber Mounting(40169980), and Sal Leaf Plate46021990)
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator For more , please kindly feel free to contact
All products will be made according to API and related international standard as per customers' requirements. Casing quick-operating thread protector is one kind of manual device for protecting casing outside thread. The structure is simple, solid durable, reliable performance. Adopting for our casing quick-operating thread protectors could save time and cost. Type O.Dmm(inch) Connection Lengthmm(inch) KHS 5 230(9-1/16) BCSG,LCSG 125(4-15/16) KHS 5-1/2 235(9-1/4) BCSG,LCSG 125(4-15/16) KHS 7 275(10-13/16) BCSG,LCSG 125(4-15/16) KHS 9-5/8 335(13-3/16) BCSG,LCSG 145(5-45/64) KHS 10-3/4 362(14-1/4) BCSG,?CSG 115(4-9/16) KHS 13-3/8 425(16-47/64) BCSG,?CSG 115(4-9/16) KHS 16 500(19-11/16) BCSG,CSG 125(4-15/16) KHS 18-5/8 565(22-1/4) BCSG,CSG 125(4-15/16) KHS 20 610(24) BCSG,?LCSG 145(5-45/64)
Material:nature rubber+EPDM Color:any color is available Thickness:8-15mm Width:1.22m Length:15-30m Warranty:5 years Installation:by adhesive,easy to install Features:Waterproof,UV resistance,aging resistance,eco-friendly,non-toxic,non-pollution...etc. Certificate:IAAF,SGS,CE,ASTM,ISO9001,ISO14001,ISO45001 Application:stadium,sports center,sports court,gym,school playground...ect.
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact
LCG is a kind of thermal interface material which coating thermal conductive polymer on a layer of fiberglass. The stickiness of the material is slightly weakness for easy procession. And insulation and tear resistance are also better. Its stickiness and flexibility, even in extremely rough and very uneven surface, also can bring a good thermal filling effect. Features & Benefits: Fiberglass substrate, anti-puncture, shear and tear resistance Only the bottom with a sticky, slightly faint on the front, easy to install High-load, low-hardness gap filling material Strong electrical insulation Typical Applications: AC / DC power supply Car equipment / charger Between the motherboard and the chassis Drive control any heating element Uninterruptible power supply (UPS) Power semiconductor-TO packaging products
Floating pneumatic rubber fenders have been in use for around 50 years. It is the leading device for marine application in the world. This compressed air filled rubber fender is used as a protective medium for ship-to-ship operation(STS), ship-to-quay(STQ) and ship-to-berthing(STB). Florescence Pneumatic Rubber Fender Construction: Outer rubber: rubber layer that covers the outside of the fender to protect the cord layers and the inner liner rubber from abrasion and other external forces. Inner rubber: liner of a rubber membrane that seals the pressurized air inside the fender. Synthetic-tyre-cord layer for reinforcement: layer made of synthetic-tyre-cord fabric, which maintains the internal air pressure of the fender. Bead ring: steel ring which is placed at one end (or both ends) of the fender and holds the end of cord layers Flange opening: steel flange, which is mounted on the fender, to which an air valve or safety valve can be adapted. Florescence Pneumatic Rubber Fender Advantages: 1. High energy absorption and with a low reaction force 2. Light weight, portable and floatable, can be installed and replaced easily 3. Heavy duty and long service life-over 10 years 4. Supplied as sling type (body only) or with chain and tire net for protection of the fender body 5. Sizes from 0.5m diameter Ã? 1.0m length up to 4.5m diameter Ã? 12m length 6. Suitable for locations with large and small tidal differences Classification of floating pneumatic fender: Fender types: 1.Net-type fender: fenders which are covered by a tire chain net, each end shall be linked together with one to two ring(s). 2.Sling-type fender: fenders which are designed to be used without a protection net. Initial internal pressure: 1.Pneumatic fender 50 (initial internal pressure 50 KPa) 2.Pneumatic fender 80 (initial internal pressure 80 KPa)
Floating pneumatic rubber fenders have been in use for around 50 years. It is the leading device for marine application in the world. This compressed air filled rubber fender is used as a protective medium for ship-to-ship operation(STS), ship-to-quay(STQ) and ship-to-berthing(STB). Florescence Pneumatic Rubber Fender Construction: Outer rubber: rubber layer that covers the outside of the fender to protect the cord layers and the inner liner rubber from abrasion and other external forces. Inner rubber: liner of a rubber membrane that seals the pressurized air inside the fender. Synthetic-tyre-cord layer for reinforcement: layer made of synthetic-tyre-cord fabric, which maintains the internal air pressure of the fender. Bead ring: steel ring which is placed at one end (or both ends) of the fender and holds the end of cord layers Flange opening: steel flange, which is mounted on the fender, to which an air valve or safety valve can be adapted. Florescence Pneumatic Rubber Fender Advantages: 1. High energy absorption and with a low reaction force 2. Light weight, portable and floatable, can be installed and replaced easily 3. Heavy duty and long service life-over 10 years 4. Supplied as sling type (body only) or with chain and tire net for protection of the fender body 5. Sizes from 0.5m diameter Ã? 1.0m length up to 4.5m diameter Ã? 12m length 6. Suitable for locations with large and small tidal differences Classification of floating pneumatic fender: Fender types: 1.Net-type fender: fenders which are covered by a tire chain net, each end shall be linked together with one to two ring(s). 2.Sling-type fender: fenders which are designed to be used without a protection net. Initial internal pressure: 1.Pneumatic fender 50 (initial internal pressure 50 KPa) 2.Pneumatic fender 80 (initial internal pressure 80 KPa)
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
Pourable, addition-curing, two-component silicone rubber that vulcanizes at room temperature. Non-toxic, odorless, two-component liquid silicone rubber, are two-component materials.Resistance high temperature of 250, shrinkage rate lower than 0.1%.
Applications of liquid pad printing silicone rubber Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface. Features of liquid pad printing silicone rubber a. resistance to deformation, high-temperature b. high printing times c. good aging resistance d. exceptional elasticity e. great printing effect
HAIR RUBBER BAND
ZIG ZAG HAIR RUBBER BAND
30 PCS BOX WOMENS RUBBER HAIR BAND IN MANY MULTI COLORS
Rubber band from vietnam good quality
