CMM-12R is designed for extension of transformer service life by restoration of dielectric strength and chemical composition of electrical insulation oil. In the process of oil regeneration, decomposition products and acidic compounds are removed, the oil is clarified, its oxidation stability is improved, and gas solvency is reduced. The unique feature of the CMM our units is the ability to regenerate transformer oil directly in a transformer with the transformer either online or offline. The functions of the unit: *Oil regeneration; *Thermal vacuum drying of oil; *Vacuum treatment of transformer; Such regeneration of oil is capable of removing sludge from paper insulation and capturing it with the sorbent. One of the advantages of the regeneration unit is the use of Fuller`s earth sorbent, which can be reactivated many times. This gives the unit the capability to process oil continuously without stops to change saturated sorbent. Even after the sorbent is completely exhausted after 1.5 to 2 years of use, it is completely environmentally safe and can be used as a filler for construction materials and mixes. The CMM 12 our unit is controlled by a computer with special status software. The scanner control system offers the operator full control of all components. The operator can control the equipment, switch to various modes of operation, monitor sensor indications and access event flow. As requested by clients, the CMM-12R can be controlled remotely via the internet. If GlobeCore assistance is required, we can simply connect to the unit through the internet and monitor the entire operation process - if there is a problem, we will see it. Many of our clients purchase equipment for operation in unstable climates, explosive environments and even at sea. The CMM units can be manufactured in various optional designs. The most popular and convenient design is placement of the unit on a one or two axle trailers - this trailer has a metal frame covered with metal sheets and is equipped with an operator room.
The Lake Fishing Magnet is a junk retrieval tool designed to effectively remove metal particles, shavings, and debris from the bottom of the well bore. The process of retrieving small, oddly shaped objects is one of the most frequent and most difficult fishing jobs. Typically, these objects are the result of bit failures that leave cones and cutters in the hole, or are an accumulation of mill cuttings, or are simply accidental droppings of unmillable objects into the hole. In these cases, the fish is nearly always an odd-shaped object that cannot be engaged in the normal manner. Fishing magnets successfully remove these small objects from the hole bottom. The tool's design incorporates generous circulation holes that wash away the cuttings and other debris that other wise would prevent contact with the magnet. Fishing magnets can be run on either wire line or pipe.
Annular Blowout Preventer(Annular BOP) is important equipment for drilling well. It widly used in onshore and offshore drilling, Geothemal driling. We supply three type of annular BOP: Bloted-cover, Wedged-Cover and Latched-cover. All type of annular BOP are strictly manucatured as per API spec 16A, have same reliable quality as other US products. There type are Camaron, shaffer and Hydril in the the word.
API Choke manifold and Kill manifold 105MPa to 35 Mpa for oilfield Working Pressure: 35Mpa---105MPa API Standerard Product Name: API Choke manifold and Kill manifold 105MPa to 35 Mpa for oilfield Origin Place:Dongying City,China Assembly: X-Mass Tree Assembly , Valves and other small connections Material:AA, BB, CC, DD, EE, FF and the other Brand:RT Exported to Canada,America,Saudi Arabia,Kuwait,Iraq,UAE,Oman,Pakistan Packing:Pallet or according to your requirement Our service:Technical support of assembly the well head products and we have some other oilfield chemicals such as high temperature foaming agent
Features (1). Sucker Rod Wrench available for different size. (2). National best quality with API standard. (3). Short on deliver time. (4). Made from heat-treated alloy steel. (5). Easy to operation. Caution (1). Before use, you should choose wrench in line with the Specification of the rod. (2). After use, it should be cleaned, and pressrved in a cool dry place. (3). After a period of time of use, it should be checked of wear and tear to ensure that the wrench is in the best working condition.
API cementing collar double stage collar with premium thread 1. Structure: 1) All inner parts are made of easily drillable aluminum alloy 2) The device can be connected directly to same type casing 3) Reliable back-pressure leak proof structure, enable grout or slurry flow with less resistance 4) Valve seat and valve disk can effectively prevent grout from flowing back 5) Hardness of base material is equivalent to API Spec N-80 6) API spec.Q1 and ISO9000 certification 2. Purpose: It be designed according to the standard of SY/T5476-92, could reduce the mixed slurry, calculate correctly, save the cement and increase cementing quality.
Description Drill pipe joint acts for conversion and connection of drill stem component in petroleum, natural gas and geology drilling work. It is used mainly for connecting of upper drill tools and lower drill tools during drilling operations. Cross-over sub is API standard Material is AISI 4145H chromium-molybdenum steel. We can offer Kelly cross-over sub, Drill pipe cross-over sub, Interim cross-over sub, Drill collar cross-over sub, Drill bit cross-over sub, Swivel cross-over sub, Fishing cross-over sub, etc. All connections are phosphatized, coated with lubricant and provided with thread protectors. All tool joints should be inspected at full length by fluorescence magnetic particle and ultrasonic method. Tool joints are for pipes from 2 3/8" to 6 5/8", grade is E 75, G 105 and S 135; upset style is EU, IEU or IU. Specification Material: AISI 4145H premium alloy steel Upset style: EU, IEU or IU Application: 2 3/8" ~ 6 5/8" dill pipes Tool joint connection DP nominal weight lb/ft Steel grade O.D.(in) I.D.(in) Pin tong space(in) Box tong space(in) Pin/Box bevel diameter(in) NC31 10.4 G105 4 1/8 2 7 9 3 61/64 S135 4 3/8 1 5/8 7 9 3 61/64 NC38 13.3 G105 5 2 7/16 8 10 1/2 4 37/64 S135 5 2 1/8 8 10 1/2 4 37/64 NC46 16.6 X95 6 1/4 3 7 10 5 23/32 G105 6 1/4 3 7 10 5 23/32 S135 6 1/4 2 3/4 7 10 5 23/32 NC50 19.5 X95 6 5/8 3 1/4 7 10 6 1/16 G105 6 5/8 3 1/4 7 10 6 1/16 S135 6 5/8 2 3/4 7 10 6 1/16
Gate valves(ball screw operation) The ball-screw operation gate valve was developed for large-bore applications, to provide manual operation at full working pressure with remakably low opening torque.The design eliminates the need for gear-type torque multipliers, and results in quicker, safer operations. The ball-screw operation gate valve shares the basic features of the "ls"series:a slab gate, patented seat seal, non-elastomeric stem seals, and metal-to-metal sealing.However, the ball-screw operation gate valve has a lower balancing stem and unique ball screw mechanism Size:3-1/16", 4-1/16", 5-1/8", 7-1/16" Wp:10, 000psi, 15, 000psi Temperature:l u, pu Mat's:aa-ff psl:1-4 pr:1-2 Honorary certificate Our products have been iso9001 certified and attained api 6a, 6d, api 7, 7k, and api 16a&16c approvals of american pertroleum insitute.All products are fully designed and manufactured in accordance with api, ansi, gb(national standards)and sy(industry standards)standards.
Downhole well drilling tool Roller reamer The Roller Reamer is designed for various reaming operation but particularly for various reaming operation but particularly for stabilization purpose when drilling in very abrasive formations. It will fit hole sizes ranging from ?6 to 28?. In addition, each body by simple adjustment of blocks and proper selection of cutters, will suit a wide range of hole sizes. Three different types(T, F, and B) of cutters are offered: Type T: Milled, machined with hardfaced sharp teeth for soft formations. Type F: Milled, machined with hardfaced flat teeth, for medium hard formations. Type B: Equipped with pressed-in tungsten carbide buttons, for hard formations.
2 " API safety relief valve 1) Safety valves are overpressure protection devices for protecting personnel and equipment, and usually installed in HP operation line for cementing/fracturing pumps, pressure vessels and other equipment under HP and high displacement. 2) The preset pressure value ranging 5000psi to 15000psi(35MPa to 105MPa) is adjusted through the top nut. When pumping pressure or operating pressure exceed the preset value, the safety valves will automatically open for pressure release. While the pressure is less than the preset value, they will be automatically closed. 3) The model of safety valve available: AQF02-105, AQF02-42,rated: 6000psi(42MPa)-15000psi(105MPa). Construction, connecting mode and size are same as SPM equivalent products; The butterfly spring inside can realize opening/closing of valves, therefore safety valves can protect people and equipment without shutting down relevant equipment. They are more reliable than shear type safety valves. Model Name Rated pressure Connection AQF02-105 2? safety valve 105MPa 2?FIG1502 tool joint pin X 2?LP AQF02-105 2? safety valve 105MPa 2?FIG1502 tool joint pin X 2? tool joint box AQF02-140 2? safety valve 140MPa 2?FIG2002 tool joint pin X 2? tool joint box
API Fully Welded Body Ball Valve Product design and scope Design standard:API 6D Length of structure:API 6D. For product beyond the scope of the standard, it shall be manufactured by specifications in BTL standard or user's requirements. Flange connecting end:ASME B16.5/ASME B16.47 Butt welding connecting end:ASME B16.25/ ASME B31.8 Wall thickness:ASME B16.34 Fireproof test:API 607/API 6FA Inspection and test:API 6D Pressure and temperature rating:ASME B16.34 Product scope:NPS 4NPS 60 CL150~CL1500 Main body material:A105,LF2,F304,F316,F304L,F316L,F51etc. Valve seat material:PTFE,RPTFE,NYLON,DEVLON,Derlin,PEEK,PPL,HNBR,FKM or metal hard seal etc. Drive device:handle, worm wheel, electric, pneumatic, pneumatic- hydraulic, electro-hydraulic, etc. -
Float collars and float shoe The float collars and float shoe are used to guide the casing to be put into the hole. It can adjust the floating power of the casing when the casing been laid in. That can certify the qualification of the cementing. The float collars and float shoe manufactured by our company use the spring driving back-pressure valve type. It has a high reliability. The structures are similar between float collar and float shoe. The lower end of the float collar is the pin connection which is connected with the casing. The upper end which is used for filling the cement has acinqfoil hole which can avoid the twist. The material of the float shoe body is the alloy steel . The upper end of the float shoe is connected with casing and its lower end is connected with the semilunar cement head. You can use the guide casing to lead it into the drilling hole. There is a back-pressure valve in the float shoe. You can use the oil well cement to fill the area between the float shoe and the body. The back-pressure can be cut by back-pressure valve. The upper hole and the lower hole will be open when the products after done . After the pressure of the circulating mud press the valve head into the lower place, the three collar valve on the valve tail will fall down automatically. The valve will press the valve seat tightly at the function of spring after the cement injection. And it will as a one-way valve function in the working. At that time, you could inject the mud into the pump from the upper end to the lower end, but the liquid of the well won`t be back in the casing below the valve or the outside circulation area of the casing.
Aimed at pump rod break, stripping, piston dropping without opening oil drainage unit during operation of oil well, no ordinary oil drainage achievement in heavy oil and paraffin troubled well, environment pollution and so on, rotary oil drainage unit is the patent product (patent no. Zl2005200845803) specially designed and developed. It has advantages of simple structure, easy operation and reliable oil drainage,
Technical specifications: Outer diameter: 114.3-508mm Standards: api sepc 5ct, 5b Steel grades: h40, j55, k55, n80, l80, c90, c95, t95, p110, q125 Connection: stc, ltc, btc and premium connection Inspection: sgs, bv Certification: iso 9001:2000 Delivery lead-time: after received deposit 10-60 days according to the quantity Payment terms: t/t, 100% l/c at sight Port of shipment: shanghai port, qingdao port or other main ports as per requested Quality control: Company has perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery 1. Inquiry evaluation: All technical data of each inquiry must be evaluated by company professional expert and get confirmation by our cooperation mill, we can confirm that all the technical data can satisfy the client's requirement and related standard 2. On-line production supervision: Online production supervision can cover the entire production process, in accordance with the contract requirements and technical specifications Supervision is begin from the re-examination of raw materials, process assessment, the production of internal control, test items, mark, packing and all the other aspects of a full range of production 3. Final product inspection: Detection of the product in accordance with international and national standards, including: the physical performance testing, chemical analysis, nondestructive testing, reliability testing and packing report 4. Logistics survey: Monitor product handling, storage, strapping, transport loading and other logistics chain
Key specifications/special features: Technical specifications: Outer diameter: 60-508mm Standards: api, sepc, 5ct Steel grades: h40, j55, k55, n80, l80, c90, c95, t95, p110, q125 Connection: stc, ltc, btc and premium connection Inspection: sgs, bv Certification: iso 9001: 2000 Delivery time: after received deposit 10-60 days according to the quantity Payment terms: t/t, 100% l/c at sight Port of shipment: xingang tianjin, shanghai port, guangdong port, ningbo port, qingdao port Quality control: Company has perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery.
Key Specifications/Special Features: Technical specifications: Outer diameter: 60-508mm Standards: API, SEPC, 5CT Steel grades: H40, J55, K55, N80, L80, C90, C95, T95, P110, Q125 Connection: STC, LTC, BTC and premium connection Inspection: SGS, BV Certification: ISO 9001: 2000 Delivery time: after received deposit 10-60 days according to the quantity Payment terms: T/T, 100% L/C at sight Port of shipment: Shanghai port, Qingdao port etc. Quality control: A perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery. 1. Inquiry evaluation: All technical data of each inquiry must be evaluated by company professional expert and get confirmation by our cooperation mill, we can confirm that all the technical data can satisfy the client's requirement and related standard 2. On-line production supervision: Online production supervision can cover the entire production process, in accordance with the contract requirements and technical specifications Supervision is begin from the re-examination of raw materials, process assessment, the production of internal control, test items, mark, packing and all the other aspects of a full range of production 3. Final product inspection: Detection of the product in accordance with international and national standards, including: the physical performance testing, chemical analysis, nondestructive testing, reliability testing and packing report 4. Logistics survey: Monitor product handling, storage, strapping, transport loading and other logistics chain
Technical specifications: Outer diameter: 60-508mm Standards: API, SEPC, 5CT Steel grades: H40, J55, K55, N80, L80, C90, C95, T95, P110, Q125 Connection: STC, LTC, BTC and premium connection Inspection: SGS, BV Certification: ISO 9001: 2000 Delivery time: after received deposit 10-60 days according to the quantity Payment terms: T/T, 100% L/C at sight Port of shipment: Shanghai port, Qingdao port etc. Quality control: Company has perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery.
Ram BOP Ram type BOP is simple and compact and is suited for land and platform applications. The ram in the BOP is pressure energized. The well pressure acts on the ram to increase the sealing force and maintain the seal even with loss of the closing pressure. Ram type BOP can be supplied with the hydraulic locking devices to lock ram hydraulically and hold the ram mechanically closed even when actuating pressure is released. The operating system is interlocked using sequence caps to ensure that the taper lock is retracted before pressure is applied to open the BOP. Ram type BOP?s bonnet are opened and closed by hydraulic pressure and the ram change is quick and easy. All operating parts, as well as, the rams and seals can be replaced on site, thus providing a completely reconditioned preventer.
Technical specifications: Outer diameter: 60-508mm Standards: API, SEPC, 5CT Steel grades: H40, J55, K55, N80, L80, C90, C95, T95, P110, Q125 Connection: STC, LTC, BTC and premium connection Inspection: SGS, BV Certification: ISO 9001: 2000 Delivery time: after received deposit 10-60 days according to the quantity Payment terms: T/T, 100% L/C at sight Port of shipment: Shanghai port, Qingdao port or as per requested Quality control: Company has perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery.
Technical specifications: Outer diameter: 25-508mm Single length: 3-14m, fixed length as per client?s requirements Standards: API SPEC 5CT, API SPEC 5B, API SPEC 5L, Slot size (mm): 0.10, 0.15, 0.2, 0.25, 0.30-3, also achieved upon customer's request. Open area up to 60%. Material: low carbon, low carbon galvanized steel (LCG), steel treated with plastic spraying, stainless steel, steel (304) End connection: plain beveled ends for butt welding or threaded. Packing: plain/bevel end with end caps, Waterproof packing, bare packing, in bundle, nest packing, standard export packing Certification: ISO 9001:2000 Delivery lead time: after received deposit 10-60 days according to the quantity Payment terms: T/T, 100% L/C at sight Port of shipment: Tianjin, Shanghai port, Qingdao port Quality control: Company has perfect quality assurance system, advanced testing equipment and high-qualified management team with control over series of activities such as contract signing, product research and development, productive process and test, product preservation and delivery.
