Adhesive Powder And Paint.
Thinner, hardner, NC paints.
Styrene acrylic co polymer, styrene acrylic emulsion, homopolymer.Manufacturer and exporter
Spray booth, automotive spray booth, paint booths.Design, manufacture, installation
Water proofing paints , bitumen.
Iron Oxide Red, Iron Oxide Black, Cement Dry Oxide Colors, White Lable Paint (Emulsion, Distemper, Water Matte, Etc), Water Proofing, Water Base Dry Cement Colors.
SAFFRO'S aura Premium Gloss Enamel gives smooth,hard & glossy finish.Its dry film has good adhesion to the surface.It has very good flow and brushability. aura Premium Gloss Enamel is a highly washable paint, thus you can wipe off most common household stains easily RECOMMENDED USE It is applied on furnitures,drums,barrels,household products,elecrical motors,doors,windows and variety of other surfaces which are not subjected to outdoor exposure FINISH :smooth and glossy COLOR As per shade card Including White and Black. COVERING CAPACITY :7 to 9 sq.mt/lit/coat at 30 to 35 micron dry film thickness,depending (ON SMOOTH MILD STEEL SURFACE) upon shades and surface. DRYING TIME :Surface dry - Less than 3 hours. :Hard dry - Less than 15 hours. Second coat application period -After 10 hours Above all properties depend upon temperature and humidity. FLASH POINT :Above 30* C (86 *F) THINNER RECOMMENDED :SAFFRO Synthetic G.P Thinner METHOD OF APPLICATION :By Brush or spray at a pressure of 40 to 50 P.S.I RECOMMENDED PRIMER :For Metal - SAFFRO R/O Z/C metal primer - SAFFRO Zinc Chrome primer yellow For Wood - SAFFRO Wood primer white For Plaster - SAFFRO Cement primer (oil base) DIRECTION FOR USE Remove dust,grease,oil,moisture,rust and other loose flakes etc.After priming the surface with recommenden primer with over night drying & sanding with emery paper,apply SAFFRO SHINE synthetic enamel using recommended thinner.Allow first coat to dry for minimum 10 hours before applying second coat.Stir the content thoroughly prior to use PACKING : 20 Ltr, 10 Ltr,4 Ltr ,1 Ltr, 500 ml,200 ml,100 ml,50 ml.
BUILDER COAT Acrylic Interior | Exterior emulsion is matt finish. FEATURES :- BUILDERCOAT Acrylic INTERIOR | EXTERIOR emulsion provides a smooth long lasting rich finish to the INTERIOR & EXTERIOR wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew. RECOMMENDED USE :- BUILDERCOAT Acrylic INTERIOR / EXTERIOR emulsion is INTERIOR / EXTERIOR wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA :- COLOURS : White & other shades FINISH : Smooth and Matt COVERAGE : On smooth primer masonry surface by brushing 1 coat: 130-160 sq. ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc) DRYING TIME : Surface drying time â?? 10-15 minutes GLOSS LEVELS/SHEEN LEVELS : Matt FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 + 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener ( As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE :- BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray THINNER :- Type 290 POT LIFE :- 3 hours min at 30�° C RECOMMENDED DFT :- 30-40 �µ. OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Type 290 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Type 290 Addition : Max 5% Nozzle Orifice : 0.28- 0.37 mm Nozzle Pressure : 1400-1800 p.s.i.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
No. Type Pure Acrylic Emulsion with high sheen. 1 FEATURES It provides a smooth long lasting rich finish with high sheen to the interior and exterior wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew. 2 RECOMMENDED APPLICATION STAR valvet glow emulsion is an interior and exterior wall finish that can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA No COLOURS White & other shades as per shade cards 1. FINISH Smooth and high sheen 2. COVERAGE On smooth primer masonry surface by brushing 1 coat: 140-160 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS Silky smooth with high sheen 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 3 years from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA No ABRASION RESISTANCE Excellent 1. WATER RESISTANCE Excellent 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins STAR velvet glow emulsion which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments Recommended Use :- This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30 - 40 OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel Finish Paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component acrylic aromatic polyurethane finish coating Recommended Use :- This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries. It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry. Physical Data COLOUR : Assorted shades FINISH : Glossy / Semi glossy / Matt SOLIDS BY VOLUME : 40 ± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 µ FLASH POINT : Base : Above 23 C Hardener : Above 23 C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS. SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional spray / By Airless Spray THINNER : Type 290 POT LIFE : 3 hours min at 30 C RECOMMENDED DFT : 30-40 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
No. Type SILK Interior Emulsion provides a luxurious finish and a silky glowing appearance to the wall. 1 FEATURES SILK Interior Emulsion is water based, Economical interior emulsion for distinctly rich and smooth finish as compared to distemper. Ideal combination of pigments & extenders mixed in a co-polymer emulsion for smooth and pleasant matt finish with Good washability. 2 RECOMMENDED APPLICATION SILK Interior Emulsion is an interior wall finish that can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA No COLOURS White & other shades as per shade cards 1. FINISH Smooth and matt 2. COVERAGE On smooth primer masonry surface by brushing 1 coat: 140-160 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS Silky smooth sheen 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
No. Type Nano acrylic Interior Wall Primer (Water Thinnable) is an economy water-based primer that enhances the application and finish of interior topcoats. 1 FEATURES Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties. 2 RECOMMENDED APPLICATION Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 90-100 sq.ft/ltr 2 coats: 60-70 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Thinner 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating. Recommended Use :- This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application. Physical Data COLOUR : Industrial Shades FINISH : Glossy / Semi-glossy SOLIDS BY VOLUME : 40 + 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30 FLASH POINT : Base : Above 23 C Hardener : Above 23C DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base: Hardener - As per our recommendations APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30- 40 . OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application. Physical Data :- COLOUR : Grey, Yellow, Beige, Red oxide FINISH : Egg Shell SOLIDS BY VOLUME : 48 ± 3% (Depends on shade) THEORETICAL SPREADING RATE : sq.mt / lit at recommended DFT of 30 µ FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : DRY TO HANDLE: 3 hr's max FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30 - 40 µ. OVERCOATING INTERVAL : MIN : 2 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous Top coats.
