I am the coating and paints for construction building supplier. Our factory is in Germany, we have the all document and certification in Europe. If you have the interest.
The product can be used on all kind of concrete walls to give the coating it is a multipurpose primer can be used in exterior and also interior of the walls. It comes in a packing size of 10 liters and 20 liters air tight buckets.
6603 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
Description
1. Tough film and good adhesion on the concrete, able to penetrate into concrete.
2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties.
3. Good resistance to impact and abrasion.
4. Easy application , drying fast.
Prepare to use
1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity.
2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application.
3. Two packs product, must be used completely during the duration of its pot life.
4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??.
5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion.
6. Keep away from heat, sparks and flame.
7. Stored with good ventilation.
8. Keep adequate ventilation during application.
9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying.
**The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel.
Color : Clear
Drying time :
Tack-free : 2 hours
Hardness : 8 hours
Full cure : 7 days (grease)
DESCRIPTION
CC-604SP is two component water based epoxy primer, composed from water based of liquid epoxy resin and hardener.
APPLICATION
1. To prime the surface and help the following application procedure to mold and decorative coating.
2. Highly resist to chemicals in non-circulated places.
3. With well adhesion ability with epoxy system or PU system application.
4. Suitable for hospital, operation room, food factory to prevent the mold, dust and bacterium.
CHARATERISTIC
1. Able to be diluted by water.
2. Anti- efflorescence , suitable for the environment with highly hygienic request.
3. Good adhesion to the moisture surface, can take as the primer for solvent-free or solvent-based epoxy resin.
CS-613W is 2-component water-based premium epoxy product.
CS-613W as admixtures can improve the properties,
particularly in relation to water absorption reduction, toughness
enhancement, vibration damping and increase of the bond strength
of cement to reinforcements other than being used as admixtures,
CS-613W is used partial replacement of fine aggregate, for
coating, sealing and repairing concrete and for coating steel
reinforcing bars for corrosion protection.
AREA OF APPLICATIONS
Repair mortar for concrete areas.
Industrial flooring.
Bonding agent for new to old concrete.
As water based primer.
Can be applied with damp surface.
FEATURE
Weatherproof and waterproof of capabilities that help prevent the deterioration of the
ground-coat material.
Low odor.
Washable with water including tools. Best to wash as soon as possible before it hardens.100% water resistant when cured.
CA-010P as a water-based primer in relation to water absorption reduction and increase the bonding strength of cement to reinforcements other than being used as admixtures increase the mechanical properties and the adhesion of the hardened material.
AREA OF APPLICATIONS
Repair mortar for concrete areas
Industrial flooring
Bonding agent for new to old concrete
Enhance adhesion strength of mortar
DESCRIPTION
Bituminous Primer is product containing oxidized bitumen and a mix of technical quick
drying solvents.
APPLICATION
Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness.
INSTRUCTIONS FOR USE
Concrete surfaces must be dry, clean and free from oil, dust or release agents.
This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment.
Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces.
PACKING
5 gallon Bucket
SHELF LIFE
The product can be stocked in closed buckets and in dry area, far from UV rays for
12 months.
TOOL CLEANING
After use clean tools with common solvents.
DESCRIPTION
CC-600SP is a two component, solvent-free epoxy system with high chemical
resistance and high bond strength. The epoxy may be applied as a primer for most
high end industrial coatings, like Epoxies, PU.
CHARATERISTIC
Easy apply
Low odor
High bond strength
Abrasion resistant
Chemical resistant
dysprosium oxide dy2o3 nanopowder
1. Used for making metal dysprosium material, glass, additive of ndfeb permanent magnet;
2. Also used for metal halogen lamp, magneto optical memory materials, yttrium iron or yttrium aluminum garnet, atomic energy industry.
Nanometer lanthanum oxide used in piezoelectric materials, electric materials, thermoelectric materials, magnetic resistance materials, luminescence materials (powder) hydrogen storage materials, optical glass, laser materials, all kinds of alloy materials, preparation of organic chemical products of catalyst, and automobile exhaust catalyst, light conversion agricultural film.
The main USES of nano-cerium oxide are: 1. Cerium oxide is used as a glass additive to absorb ultraviolet and infrared rays and has been used in automobile glass.Not only can prevent ultraviolet ray, also can reduce the temperature inside the car, thereby save air conditioning electricity.2. The application of nano-cerium oxide to automobile exhaust purification catalyst can effectively prevent a large amount of automobile exhaust gas from being discharged into the air.3. Nano cerium oxide has been widely used in polishing materials.4, nanometer cerium oxide can also be used in hydrogen storage material, thermoelectric materials, nano oxide cerium tungsten electrode, ceramic capacitors, piezoelectric
solvent free flooring epoxy system two components used for producing high quality epoxy smooth flooring with high glossy surface. Where it based on epoxy resin and agents which are specially selected for their ability to withstand chemical attack
Properties @ 25 c
Color: White , grey , all required colors
Gloss: Glossy
Solid content by (WT): 100 %
Mixing Ratio: 4 A : 1 B
Specific gravity (mix ): 1. 60 0.03 g/cm3
Pot life: 35 min.
Temp. of Application: ( 15 35 ) C
Full curing time: 7 days
Rate of use: 3 -5 m2/ kg ( depending on surface conditions )
Setapol 260 1C is an elastic coated polyurethane membrane of one component for long-lasting waterproofing.It has hydrophobic resistance to sun and frost while it is breathable with anti-corrosion properties.Setapol 260 1C is ideal for the sealing of roofs , balconies ,rooms , gardens , pots and for the protection of thermal insulation foam polyurethane.
It also has coverage of 1.5 - 2.0 kg / m2 in two or three layers.
Setapol 450ML 1C is an elastic paint of aliphatic polyurethane base of a component with good mechanical strength.It has a particularly high resistance to sun and frost.There is also no yellowing on the surface.Setapol 450ML 1C is ideal as a finishing coat resistant to light alloys.
Desnamel Fast Dry is a fast -drying alkydic final coating with good gloss and preservation of hue.It is used as a primer as long as a final coating for steel in a slightly corrosive environment.
Desmopol Topcoat is a semi-acrylic polyurethane coating of two-components aliphatic isocyanate with good gloss .It is used as a final coating for the protection of structural steel in extremely corrosive environment, when light steadiness and preservation of the gloss is required.The minimum heat for drying is -10
Setapol 400ML 1C is an elastic paint of aliphatic polyurethane base of a component with good mechanical strength.There is no yellowing on the surface.Setapol 400ML 1C is ideal as a final sealant on moderate pedestrian traffic surfaces.It has coverage of 0.15 - 0,25 kg / m2 in two or three layers.
6603 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
