Product introduction: Oil Spill Dispersant is mainly made of non-ionic surfactant by special process. Oil Spill Dispersant is a water-based oil spill dispersant with high efficiency and easy biodegradation. Oil Spill Dispersant is also the second generation of oil spill dispersant products that attract international attention. Scope of application: Oil Spill Dispersant is applicable to a variety of hydrocarbon products (such as heavy oil, clean oil, lubricating oil, diesel, mixed oil, etc.). Oil Spill Dispersant is used in different oil spill site environments, such as oil spill in open waters, oil spill in loading or lightering, oil spill in large tanks or oil tanks, and salvage engineering to control the spread of oil pollution. The oil remover is also used for cleaning heavy oil stains such as oil tanks, engine rooms, bulkheads, oil pipes and guardrails on board. Usage: when spraying oil spill dispersant on the water surface, timely adjust the spraying rate and the moving speed of the vehicle to emulsify and disperse the oil spill. Spray the oil eliminator from the upper wind head to the lower wind. Spray the Oil Spill Dispersant around the oil film first and gradually towards the middle of the oil film. It can make full use of the mixing effects of wind and wave, bow wave, propeller or drainage, or stir the water surface of the spraying part with the help of faucet water injection or towing mixing device. Spraying oil eliminator before the spilled oil arrives at the beach can reduce the degree of pollution and the workload of cleaning. Spraying dose: generally 20% of the oil spill
Product introduction: This DC transfer pump is for fueling diesel, kerosene, not for gasoline. It used to fill or empty engines, tanks and all kinds of machinery, tractor and farm equipments. Product details: Pumping Fuel: Diesel and kerosene Power: Electric Application: Transfer fuel to vehicles or construction fields' engineering work or maritime navigation.Technical Parameters: Flow Rate : (20-40)L/min Rated Voltage : DC12V or DC24V Pressure: 0.16-0.18Mpa; 1.6-1.8bar; 23-26psi Suction Lift : 3-5m Head Lift: 5-10m In-out: In BSPT3/4", Out BSPT3/4" Voltage: 12V/24V Power: 245W Flowrate: 50L/min height: 10m Inlet diameter: 25mm Outlet diameter: 25m
The Lubrication oil system including the following equipments: 1, Oil pump 2, grease pump, 3, oil hose reel, 4, grease hose reel, 5, waste oil collecting machine, 6, hose 7, others equipment (see the actual requirement).
Art. 33120 Oil Control Gun Oil Control Gun with Flexibe Outlet Oil Control Gun with Rigid Outlet These oil control guns are adaptable to various workshop in conjunction with air-operated oil system. They are first-rate product in my company, also they can be your first choice. Features Dispenses lubricating oils up to SAE 240, and antifreeze; Utilises a straight through flow path to reduce pressure drop; Latching trigger for ease of use; Installs a ball bearing swivel inlet to ensure smooth operation and prevent the hose from kinking; Non-drip automatic delivery nozzle; Trigger guard. Specifications Wetted components: Aluminium, mild steel, nitrile rubber Max. Operating pressure: 7 000 kPa (1000 psi, 70 bar) Flow rate: Up to 30 L/min (8 US gal per min) Max. Operating temp: 70 C (158 F) Inlet connection: 12" BSP or NPT (F) Weight (approx): 800 g (1.8 lbs)
Vacuum Degasser are used to remove the small entrained gas bubbles left in the mud by the mud/gas separator. These units are positioned downstream from mud/gas separators, shale shakers and mud cleaners, while hydrocyclones and centrifuges follow in the arrangement. Operational Theory: Vacuum degasser utilize negative pressure by vacuum pump to withdraw entrained gases from the mud. In order for this to work, mud is pumped through a venturi, which develops a negative pressure in the vessel by vacuum pump, thus sucking mud into the unit. The choice between horizontally- or vertically-mounted units is typically based on the footprint requirements of the specific rig. Features and Advantages: 1.Scientific reasonable design for structure,it can get effective gas fluids separation,filter out impurities to guarantee vent pipe always clear. 2.Adopt belt drive,avoid the complication of the reducing gear,ensure the long working time without trouble. 3.Water circle type of vacuum pump is always at a constant temperature,apply to pump the flammable and explosive. 4.High degassing efficiency,up to 95%. 5.There is gas-water separator in vacuum degasser,which can avoid the gas and fluids are all removed together,and also can supply water for vacuum pump,saving water and environment-friendly How to contact us?
Vacuum Degasser are used to remove the small entrained gas bubbles left in the mud by the mud/gas separator. These units are positioned downstream from mud/gas separators, shale shakers and mud cleaners, while hydrocyclones and centrifuges follow in the arrangement. Operational Theory: Vacuum degasser utilize negative pressure by vacuum pump to withdraw entrained gases from the mud. In order for this to work, mud is pumped through a venturi, which develops a negative pressure in the vessel by vacuum pump, thus sucking mud into the unit. The choice between horizontally- or vertically-mounted units is typically based on the footprint requirements of the specific rig. Features and Advantages: 1.Scientific reasonable design for structure,it can get effective gas fluids separation,filter out impurities to guarantee vent pipe always clear. 2.Adopt belt drive,avoid the complication of the reducing gear,ensure the long working time without trouble. 3.Water circle type of vacuum pump is always at a constant temperature,apply to pump the flammable and explosive. 4.High degassing efficiency,up to 95%. 5.There is gas-water separator in vacuum degasser,which can avoid the gas and fluids are all removed together,and also can supply water for vacuum pump,saving water and environment-friendly
Description AC Power 220-V. Electric Fuel Transfer Pump 50L. Per Minute Digital Fuel Meter Trolley Wheel Plate & Tyres 6.00-16 Size = 2 Nos. Suction Pipe House x 12 Ft. Anti Static House Dispensing Nozzle Manual With Swivel Tractor Toeing Bar
Typical separation 1.Chemical Industry: gypsum, thiamin, salt, ferric sulfate, boric acid, borax, rubber additive, dye, heavy oil and other chemical products. 2.Food industry: kitchen salt, sodium glutamate, food additive, Chemical seasonings, sugar 3.Pharmaceutical:Extraction of vitamin, biotic, traditional Chinese medicine and other various drugs 4.Mine and Metallurgy: Copper, zinc, minerals, and metal refining 5. Environmental Protection: with acid discharge, pure water sludge and sewage sludge, etc
Product Description: This kind centrifuge is a separator for separating solid, liquid and liquid for chemical, pharmaceutical, oil, foodstuff, milk industry, daily industry and defense industry etc.. It has three types for solid discharge such as central value deslagging, artificial deslagging, and water push deslagging. The first type is mainly used in the desoponificating of oil refining, and the last two types are used in degumming and dehydrating, they are all applicable for liquid-liquid-solid and liquid-solid separation. It has advantages of high speed, smooth operating, compact structure, small footprint, all sealed of the inlet and discharge, little noise, good separation. Application: It is widely used in chemical, pharmaceutical, oil, foodstuff, milk industry, daily industry and defense industry such as: 1. Food stuff industry: For animal protein extraction and separation, as well as in meat processing for refining animal lipid or in concentrating and separating aquatic products of fish oil, in clarifying and degreasing milk, for the clarification of beer and malt, sparkling wine, fruit juice and drinks and so on. 2. Chemical industry: Mainly used in separating industrial chemicals, paint and coatings. Also it could be used in the clarification and purification of wastewater from light, textile, chemical fiber industry as well as analogues of greater density solid-phase. Also it is used for concentrating and clarifying of natural rubber, it separates rubber milk into concentrated latex and clear pastern. At the same time it removes the solid impurities in serum. 3. Pharmaceutical Industry: Mainly used in separating biopharmaceuticals, pharmaceutical medicine, vaccines, mycelium, glucose, insulin, vitamins, antibiotics, pigments, proteins, spices and so on. 4. Oil industry: It can be used vegetable oil, animal fat, fish oil, soap oil, biodiesel and other lipid-foot, swill oil as raw material, through new centrifugal separation process of trans- esterification and access . 5. Other industry: It mainly used to remove the water and mechanical impurities contained in equipment fuel and lubricants in boating mainframe, diesel power station as well as other types of mineral oil, in order to reduce diesel engine or other mechanical wear and extend the useful life of the mechanical. Also applies to separate and clarify similar materials of waste oil in other petrochemical industries, such as black oil, delayed coking oil, washing oil and recycle oil and so on.
Product Description Introduction: DISC olive oil filter /purifier are mainly applied in: 1.the purification and clarification of all kinds of vegetable oil palm oil ,coconut oil, olive oil, soybean oil, sunflower oil ect. 2, for plant oil refining, animal oil separation , Biodiesel separation ect .continuous degreasing, dephosphorization, de-soap, dehydration and other procedures. Reducing the harmful ingredients in vegetable oil, to meet national standards. 3.some harmful substances of the oil. This series is oil purifier and clarifier, we also have other clarifier series and concentrator series. Oil water separator/ the diesel, light fuel oil, heavy fuel oil, transformer oil, lube oil,Marine mineral oil. Main Feature: Simple, compact and robust design Highest separation efficiency in removing solids and water No pre-filtration necessary Environmentally friendly sludge disposal (no cartridges) Automatic, unattended operation Easy maintenance Low operating cost Proven reliability and long lifespan Reliable process for maximum performance Designing including as below Feed pump with an electric motor Self-cleaning centrifugal separator with electric motor Control panel with local operator device Atmospheric sludge tank complete with sludge pump Instrument air distribution system Wired and piped to skid limit Module base frame with drip pan, lifting lugs and earthing Suitable offshore painting Tagging and marking Factory Acceptance Test (FAT) Documentation
TRIO ELC machine for filtration of hydraulic oil, turbine oil and gear oil, contamination removal less than micron, capacity 50 liter, 100 liter.
Condition:New Applicable Industries:Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works , Energy & Mining, Food & Beverage Shops, Advertising Company Showroom Location:Egypt, Canada, United Kingdom, United States, Italy, France, Germany, Viet Nam, Philippines, Brazil, Peru, Saudi Arabia, Indonesia, Pakistan, India, Mexico, Russia, Spain, Thailand, Morocco, Kenya, Argentina, South Korea, Chile, UAE, Colombia, Algeria, Sri Lanka, Romania, Bangladesh, South Africa, Kazakhstan, Ukraine, Kyrgyzstan, Nigeria, Uzbekistan, Tajikistan, Japan, Malaysia, Australia Video outgoing-inspection:support Machinery Test Report:support Marketing Type:Hot Products Warranty of core components: The latest recommended products Core Components:Nano-gold electric field, Smart power, Carbon steel sheet Place of Origin:Shanghai, China Brand Name:KUARBAA Warranty:1 year warranty and lifetime maintenance service Product name:Smoke Purifier Machine Type:Air Filter Function:Cleaning Machine Oil Mist Material:Carbon Steel Spraying Voltage:220/230ACV/50/60HZ HEPA Filter:99.999% Efficiency Inlet velocity:3M/S applied temperature:-30-65 Contour size:850-710-640mm Equipment weight:98KG After Warranty Service:Video technical support, Online support, Spare parts Local Service Location:Egypt, Canada, United Kingdom, United States, Italy, France, Ge
CMM-12R is designed for extension of transformer service life by restoration of dielectric strength and chemical composition of electrical insulation oil. In the process of oil regeneration, decomposition products and acidic compounds are removed, the oil is clarified, its oxidation stability is improved, and gas solvency is reduced. The unique feature of the CMM our units is the ability to regenerate transformer oil directly in a transformer with the transformer either online or offline. The functions of the unit: *Oil regeneration; *Thermal vacuum drying of oil; *Vacuum treatment of transformer; Such regeneration of oil is capable of removing sludge from paper insulation and capturing it with the sorbent. One of the advantages of the regeneration unit is the use of Fuller`s earth sorbent, which can be reactivated many times. This gives the unit the capability to process oil continuously without stops to change saturated sorbent. Even after the sorbent is completely exhausted after 1.5 to 2 years of use, it is completely environmentally safe and can be used as a filler for construction materials and mixes. The CMM 12 our unit is controlled by a computer with special status software. The scanner control system offers the operator full control of all components. The operator can control the equipment, switch to various modes of operation, monitor sensor indications and access event flow. As requested by clients, the CMM-12R can be controlled remotely via the internet. If GlobeCore assistance is required, we can simply connect to the unit through the internet and monitor the entire operation process - if there is a problem, we will see it. Many of our clients purchase equipment for operation in unstable climates, explosive environments and even at sea. The CMM units can be manufactured in various optional designs. The most popular and convenient design is placement of the unit on a one or two axle trailers - this trailer has a metal frame covered with metal sheets and is equipped with an operator room.
The Lake Fishing Magnet is a junk retrieval tool designed to effectively remove metal particles, shavings, and debris from the bottom of the well bore. The process of retrieving small, oddly shaped objects is one of the most frequent and most difficult fishing jobs. Typically, these objects are the result of bit failures that leave cones and cutters in the hole, or are an accumulation of mill cuttings, or are simply accidental droppings of unmillable objects into the hole. In these cases, the fish is nearly always an odd-shaped object that cannot be engaged in the normal manner. Fishing magnets successfully remove these small objects from the hole bottom. The tool's design incorporates generous circulation holes that wash away the cuttings and other debris that other wise would prevent contact with the magnet. Fishing magnets can be run on either wire line or pipe.
Annular Blowout Preventer(Annular BOP) is important equipment for drilling well. It widly used in onshore and offshore drilling, Geothemal driling. We supply three type of annular BOP: Bloted-cover, Wedged-Cover and Latched-cover. All type of annular BOP are strictly manucatured as per API spec 16A, have same reliable quality as other US products. There type are Camaron, shaffer and Hydril in the the word.
API Choke manifold and Kill manifold 105MPa to 35 Mpa for oilfield Working Pressure: 35Mpa---105MPa API Standerard Product Name: API Choke manifold and Kill manifold 105MPa to 35 Mpa for oilfield Origin Place:Dongying City,China Assembly: X-Mass Tree Assembly , Valves and other small connections Material:AA, BB, CC, DD, EE, FF and the other Brand:RT Exported to Canada,America,Saudi Arabia,Kuwait,Iraq,UAE,Oman,Pakistan Packing:Pallet or according to your requirement Our service:Technical support of assembly the well head products and we have some other oilfield chemicals such as high temperature foaming agent
Features (1). Sucker Rod Wrench available for different size. (2). National best quality with API standard. (3). Short on deliver time. (4). Made from heat-treated alloy steel. (5). Easy to operation. Caution (1). Before use, you should choose wrench in line with the Specification of the rod. (2). After use, it should be cleaned, and pressrved in a cool dry place. (3). After a period of time of use, it should be checked of wear and tear to ensure that the wrench is in the best working condition.
API cementing collar double stage collar with premium thread 1. Structure: 1) All inner parts are made of easily drillable aluminum alloy 2) The device can be connected directly to same type casing 3) Reliable back-pressure leak proof structure, enable grout or slurry flow with less resistance 4) Valve seat and valve disk can effectively prevent grout from flowing back 5) Hardness of base material is equivalent to API Spec N-80 6) API spec.Q1 and ISO9000 certification 2. Purpose: It be designed according to the standard of SY/T5476-92, could reduce the mixed slurry, calculate correctly, save the cement and increase cementing quality.
Description Drill pipe joint acts for conversion and connection of drill stem component in petroleum, natural gas and geology drilling work. It is used mainly for connecting of upper drill tools and lower drill tools during drilling operations. Cross-over sub is API standard Material is AISI 4145H chromium-molybdenum steel. We can offer Kelly cross-over sub, Drill pipe cross-over sub, Interim cross-over sub, Drill collar cross-over sub, Drill bit cross-over sub, Swivel cross-over sub, Fishing cross-over sub, etc. All connections are phosphatized, coated with lubricant and provided with thread protectors. All tool joints should be inspected at full length by fluorescence magnetic particle and ultrasonic method. Tool joints are for pipes from 2 3/8" to 6 5/8", grade is E 75, G 105 and S 135; upset style is EU, IEU or IU. Specification Material: AISI 4145H premium alloy steel Upset style: EU, IEU or IU Application: 2 3/8" ~ 6 5/8" dill pipes Tool joint connection DP nominal weight lb/ft Steel grade O.D.(in) I.D.(in) Pin tong space(in) Box tong space(in) Pin/Box bevel diameter(in) NC31 10.4 G105 4 1/8 2 7 9 3 61/64 S135 4 3/8 1 5/8 7 9 3 61/64 NC38 13.3 G105 5 2 7/16 8 10 1/2 4 37/64 S135 5 2 1/8 8 10 1/2 4 37/64 NC46 16.6 X95 6 1/4 3 7 10 5 23/32 G105 6 1/4 3 7 10 5 23/32 S135 6 1/4 2 3/4 7 10 5 23/32 NC50 19.5 X95 6 5/8 3 1/4 7 10 6 1/16 G105 6 5/8 3 1/4 7 10 6 1/16 S135 6 5/8 2 3/4 7 10 6 1/16
Gate valves(ball screw operation) The ball-screw operation gate valve was developed for large-bore applications, to provide manual operation at full working pressure with remakably low opening torque.The design eliminates the need for gear-type torque multipliers, and results in quicker, safer operations. The ball-screw operation gate valve shares the basic features of the "ls"series:a slab gate, patented seat seal, non-elastomeric stem seals, and metal-to-metal sealing.However, the ball-screw operation gate valve has a lower balancing stem and unique ball screw mechanism Size:3-1/16", 4-1/16", 5-1/8", 7-1/16" Wp:10, 000psi, 15, 000psi Temperature:l u, pu Mat's:aa-ff psl:1-4 pr:1-2 Honorary certificate Our products have been iso9001 certified and attained api 6a, 6d, api 7, 7k, and api 16a&16c approvals of american pertroleum insitute.All products are fully designed and manufactured in accordance with api, ansi, gb(national standards)and sy(industry standards)standards.
