Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact
LCG is a kind of thermal interface material which coating thermal conductive polymer on a layer of fiberglass. The stickiness of the material is slightly weakness for easy procession. And insulation and tear resistance are also better. Its stickiness and flexibility, even in extremely rough and very uneven surface, also can bring a good thermal filling effect. Features & Benefits: Fiberglass substrate, anti-puncture, shear and tear resistance Only the bottom with a sticky, slightly faint on the front, easy to install High-load, low-hardness gap filling material Strong electrical insulation Typical Applications: AC / DC power supply Car equipment / charger Between the motherboard and the chassis Drive control any heating element Uninterruptible power supply (UPS) Power semiconductor-TO packaging products
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
Description Peek (Polyether ether ketone) is a high-performance thermoplastic material that is known for its excellent mechanical, thermal, and chemical properties. Peek is often used in industrial applications where high temperature, chemical resistance, and mechanical strength are required. A peek seat is a component that is often used in valve applications. It is a seat made from peek material that is used to provide a tight seal between two components. A peek o-ring, on the other hand, is a type of o-ring made from peek material. O-rings are mechanical seals that are used to prevent the leakage of gases or liquids. Peek o-rings are known for their excellent chemical resistance, high-temperature resistance, and low friction coefficient. They are often used in applications where standard elastomeric o-rings would not be suitable due to their inferior properties. Sealing principle: The peek seat is a V-spring that is used as a force-applying element. The seal housing made of PTFE composite or peek has a good leak and crush resistance. As a seat seal ring, it is widely used in high-pressure valves, usually, the inner and outer seal rings of the seat are used together.
Crumb rubber plastic and cardboard bales
Name of Product: Ribbed Smoked Sheet - RSS4, RSS5 and Lot Sheets Price of Product: Subject to market price, as of June 10, 2024 Approx. CAD.5 per KG for RSS4 in Canada Product Origin: Kerala, India
Logiplug inflatable sewer plugs Logiplug inflatable sewer plugs can be used in a wide variety of applications such as by-pass pumping, flow control and flow diversion. Logiplug pneumatic plugs can be used for completely stopping water flow when the flow-thru is plugged off. Logiplug rubber plugs are manufactured on lightweight aluminum mandrels. Steel or stainless-steel mandrels are also available upon request. The SBR rubber sleeve is reinforced with two plies of nylon cords for increased durability. Different types of elastomers are available depending on your needs. All Logiplug inflatable sewer plugs are factory tested, at an inflation pressure corresponding to twice the recommended pressure. Each plug is shipped with an inspection certificate and a safety information leaflet.
- Item - Rubber Band / Elastic Band - Round Section. - Rubber Compound in Bands: 100%, 90%, 80%, 70%, 60$ - Colors - Natural / Red / Green / Yellow & other colors as required. - Sizes - Thickness / Diameter as required. - HS Code: 4016 9920 Packing Per Poly Bag : 1kg, 500 gm, 150 gm, 75 gm, 1 Lb, 4 oz(or) upon your request (By digital scale). Bands Packed in Poly Bag / Boxes as per required weights Packed in Cartons with required Poly Bags/ Boxes Quantity Per Container In 20 Ft :Approximately 660 Cartons In 40 Ft :Approximately 1400 Cartons In 40ft HQ :Approximately 1550 Cartons Delivery : 30 - 40 Days // As agreed Payment :LC at sight // 30% Advance and Balance Before Shipment Origin of goods :THAILAND
Reclaimed rubber.
Rubber Crumb.
Rubber crumb.
Crumb rubber.
Anti vibration rubber pad.
Crumb rubber.
Rubber powder.Manufacture
EMI shielding and gaslets, o-rings (all materials).
Extruded & molded rubber products, rubber cords, tubes, squares rectangles.
Rubber products.
Rubber crumb, rubber product.
