Versatile and professional LTE 450 router with WiFi, Dual-SIM and further expansion options DIN rail mountable, versatile, wireless DUAL SIM industrial LTE router with WiFi, Ethernet port and several expansion possibilities. The device uses the open source OpenWRT® operation system, supporting web admin interface. The following expansion options can be chosen: RS232/RS485, Wireless MBus or IO-expansion. Communication Supporting the LTE 450 (450MHz Cat.4 module) Usage of Dual SIM cards WiFi (for the connected devices) It can be extended with the listed modules Self-developed expansion modules to integrate Ethernet LAN/WAN Software/Configuration Easy to use open source OpenWRT® software Opportunity for the developers to implement and use self-developed system or applications The device can be parameterized on its web page by the local/remote interface Firmware & software updates and parameterizing remotely by the M2M Device Manager® software Security System monitoring, auto restart mode High availability Extended tests during the development Protection from network attack, traffic monitoring helps to reduce data usage Application Wireless data transmission, routing Secondary/backup route Industrial M2M machines (to a Scada) Utility smart meters (remote readout) Safety camera, DVR
Data concentrator with 32 digital inputs and Modbus RTU communication Cost-effective industrial solution for reading out the data of consumption metering devices (e.g. water, gas, electricity meters) equipped with contact or pulse output line. Furthermore, the concentrator can connect to any kind of measurement devices, PLCs, controlling machines, data collection system, automata or a network analyzer. The device is capable of collecting and storing data of up to 32 endpoint devices through the input lines. The M2M Modem Plus IO® device is connected through the RS485 port to read out the input values with Modbus RTU protocol. Connection 32x digital inputs (4 segment x 8 isolable inputs, operation mode selection by jumper) Receiving and counting the contact/pulse signals Dry/wet contact relay Open collector input Receiving the output signals as input signals (alternate wiring) Receiving reed/hall sensor outputs RS485 output (ModBus RTU protocol towards the modem) Software/Configuration Modbus protocol communication Readout of Modbus counters, registers PLC compatibility Configuration software (locally on serial port) Security Watchdog circuit and system monitoring Data storage into non-volatile memory Application Data collection and counting Measurement and data collection systems Forwarding industrial system or PLC data Monitoring industrial or measurement devices Remote control
Professional, wireless 4G LTE Cat.3 router DIN-rail mountable, universal 4G LTE router with wireless data forwarding capabilities, Ethernet port and industrial design. The device uses the open source OpenWRT® operation system and provides web admin interface. Communication Supporting the 4G LTE Cat.3 (Telit® module) Ethernet LAN/WAN Software/Configuration Easy to use open source OpenWRT® software with webadmin interface Opportunity for the developers to implement and use self-developed system or applications Firmware & software updates and parametrizing remotely by the M2M Device Manager® software Security System monitoring, auto restart mode High availability and stable IP connection Protection from network attack, traffic monitoring helps to reduce data usage Application Wireless data transmission, routing Secondary/backup route Industrial M2M and measurement, data collecting devices, PLCs (to a Scada) Remote access, monitoring, maintenance Utility smart meters (remote readout) Safety camera, DVR
*. Input:100-240VAC 50/60Hz *. Output:48VDC 0.32A 15.5W *. AC socket: IEC320 C6 or C8 optional *.Ethernet rate: 10/100/1000Mbps gigabit *.Pin assignment: Pin 12/36 & 45/78, 4 pairs *.Protocol Standard:Active type, compliance with IEEE802.3 Standard *.Appliance: IP camera, poe switch, wifi AP ect *.output type: Single output *.Efficiency: 84% Min *.Ripple & Noise:4800mV p-p *.MTBF:45000hours *. Protection:OVP SCP OCP OTP *. Material: Plastic housing, Compliance UL 94 V-0 *. Warranty:2 years *.Color: Black
New Passive PoE Injector single output 52VDC 90W PoE power supply Dual RJ45 PoE adapter for 5G Ethernet Switch Antenna *. Input:100-240VAC 50/60Hz*. Output: 52Vdc 90W *. AC socket: IEC320-C14, 3 pins socket *.Ethernet rate:1G/2.5G/5G *.Connector:1*RJ45 for PoE + 1*RJ45 for LAN *.Pin assignment: Pin 12/36 & 45/78, 4 pairs *.Protocol Standar:Non-IEEE802.3AF/802.3AT, Passive type *.Appliance: IP camera, poe switch, wifi AP ect *.output type: Single output *.Efficiency: 85% Min *.Ripple & Noise:480mV p-p *.MTBF:45000hours *. Protection:OVP SCP OCP OTP *. Material: Plastic housing, Compliance UL 94 V-0 *. Warranty:2 years *.Color: Black Company Profile * GRT established in 2007, is the manufacturer who specialized in research and development, production, sales, service as one. GRTis located in Shunde(the Kingdom of Home-Appliance), owns several Senior professional engineers, to research, develop and design kinds of power supplies and provide various customized solutions. *.All items is with 2% output accuracy and compliance with international standard. Owns license of Importing and Exporting and Pass kinds of international approvals like as UL, GS,TUV,CCC,CE, FCC,ROHS,ERP,PSE, CB,SAA ect, suitable for the global markets. *.Owns ISO9001:2015 and kinds of advanced machines for production and testing. *.Owns two green workshops which covers area 8000 square meters. monthly output upto 880K Our Services & Strength *. Offer OEM service, accept print your own logo and special requirements for package and others *. Experienced Technical team, to provide kinds of solutions *. Provided authorized certifications *. 100% Full Burn-In Testing, strictly inspect and control during production FAQ 1.MOQ :500pcsas the the first order, small qty (more than 100pcs) will be acceptable. 2.Sample terms *Common sample:2pcs are free offered, the buyer shall pay for the shipping cost and Tax; Leadtime within one week *. Special Sample: the buyer shall pay for the sample cost, shipping cost, Tax, R&D cost (if caused) Leadtime will be confirmed when the project starting 3. Mass production 20-25 working days, from the day got the confirmed order and payment 4. Shipment By Sea, By Air, By Train, By Express ect 5.Payment: T/T in advance, L/C
Passive PoE Injector 24VDC 1A 24W PoE adapter 100Mbps Ethernet switch antennae networking AP CCTV camera *. Input:100-240VAC 50/60Hz *. Output: 48Vdc 1.25A 60W *. AC socket: IEC320-C14, 3 pins socket *.Ethernet rate:10/100/1000Mbps Gigabit *.Connector:1*RJ45 for PoE + 1*RJ45 for LAN *.Pin assignment: Pin 12/36 & 45/78, 4 pairs *.Protocol Standard:Passive type, Non-compliance with IEEE802.3 Standard *.Appliance: IP camera, poe switch, wifi AP ect *.output type: Single output *.Efficiency: 86% Min *.Ripple & Noise:480mV p-p *.MTBF:45000hours *. Protection:OVP SCP OCP OTP *. Material: Plastic housing, Compliance UL 94 V-0 *. Warranty:2 years *.Color: Black
Gigabit Passive PoE Injector 48VDC 0.5A 24W PoE adapter 1000Mbps Ethernet switch antennae networking AP CCTV camera *. Input:100-240VAC 50/60Hz *. Output:48VDC 0.5A 24W *. AC socket: US plug, 2 pins plug *.Ethernet rate: 10/100/1000Mbps gigabit *.Pin assignment: Pin 12/36 & 45/78, 4 pairs *.Protocol Standard:Passive type, Non-compliance with IEEE802.3 Standard *.Appliance: IP camera, poe switch, wifi AP ect *.output type: Single output *.Efficiency: 84% Min *.Ripple & Noise:4800mV p-p *.MTBF:45000hours *. Protection:OVP SCP OCP OTP *. Material: Plastic housing, Compliance UL 94 V-0 *. Warranty:2 years *.Color: Black
High intensity focused . The effective penetration depth of High intensity focused is 8cm, covering the whole neural network anddriving the contraction of the whole musclelayer; .The effect of fat apoptosis and "super muscle exercise" can never be achieved by physicalexercise; .Studies in the United States have shown that the effect of four treatments is the best; .The treatment experience is good. EMS Most of the energy of the current is concentrated in thesurface layer, only a small part can reach the muscle; Feeling a slight tingling or contraction; Advantageï¼? Easy to lose weight and rebuild your body shape Dissolve fat Simplicity ofoperator Tyra firming thin arms thin legs thin belly thin body thin buttock
Mfr No: IPP60R060P7XKSA1 Manufacturer: Infineon Technologies Package: TO-220-3 Category: Single FETs, MOSFETs Rohs: Lead free / RoHS Compliant Description: High-voltage, high-speed power electronics component for demanding industrial and commercial applications
Usb hub lapcare,zebronics,adnet,prodot,enter and in expensive fingers,portronics etc.
This FiberHTT 1550 nm FP 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 80km. The SFP+ 80km module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
This FiberHTT 1310nm FP 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 40km. The SFP+ 40km module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
This Hengtaitong 1310 nm FP 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km. The SFP+ 10km module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
This FiberHTT 1310 nm FP 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 2km. The SFP+ 2km module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
The Hengtaitong SFP transceivers are high performance, cost effective modules supporting data-rate of 1.25Gbps and 40km transmission distance with SMF. The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with atrans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.
The FiberHTT HPBT3R2-LR single mode transceiver is small form factor pluggable module for duplex optical data communications such as 10GBASE-ER/EW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability. The HPBT3R2-LR module is designed for single mode fiber and operates at a nominal wavelength of 1330nm or 1270nm;.The transmitter section uses a multiple quantum well DFB, which is class 1 laser compliant according to International Safety Standard IEC-60825.The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC
The FiberHTT HPBT2R3-LR single mode transceiver is small form factor pluggable module for duplex optical data communications such as 10GBASE-ER/EW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability. The HPBT2R3-LR module is designed for single mode fiber and operates at a nominal wavelength of 1270nm or 1330nm;.The transmitter section uses a multiple quantum well DFB, which is class 1 laser compliant according to International Safety Standard IEC-60825.The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.
The FiberHTT HPBT3R2-L2 single mode transceiver is small form factor pluggable module for duplex optical data communications such as 10GBASE-ER/EW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability. The HPBT3R2-L2 module is designed for single mode fiber and operates at a nominal wavelength of 1330nm or 1270nm;.The transmitter section uses a multiple quantum well DFB, which is class 1 laser compliant according to International Safety Standard IEC-60825.The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.
The FiberHTT H9S3124-L2 Transceiver is a high performance, cost effective module, which is compliant with Gigabit Ethernet and Standard of IEEE-802.3. This transceiver operates at the normal wavelength of 1310nm. The transmitter section incorporates an advanced FP and driver IC with temperature compensation and automatic power control function. The receiver section incorporates an efficient InGaAs/InP PIN photodiode and transimpedance with AGC for wide dynamic range. The transceiver has excellent immunity and reliability.
The FiberHTT H9B5324-L2 Transceiver is a high performance, cost effective module, which is compliant with Gigabit Ethernet and Standard of IEEE-802.3. This transceiver operates at the normal wavelength of Tx 1550nm Rx1310nm. The transmitter section incorporates an advanced DFB and driver IC with temperature compensation and automatic power control function. The receiver section incorporates an efficient InGaAs/InP PIN photodiode and transimpedance with AGC for wide dynamic range. The transceiver has excellent immunity and reliability.
