Hastelloy C276 is a tungsten added nickel-molybdenum-chromium super alloy designed to offer excellent corrosion resistance in wide range of severe environments. The chromium in Hastelloy C276 conveys resistance to oxidizing media while high molybdenum and nickel content makes the nickel alloy specially resistant to pitting and crevice corrosion in reducing environments. Chemical Composition Hastelloy C276 Analysis NiBal Mo15 17 Cr14.5 16.5 Fe4 7 W3 4.5 Co2.5 max Mn1.0 max C0.01 max v0.35 max P0.04 max S0.03 max Si0.08 max
Monel 400 is a nickel-copper super alloy that is resistant to steam at high temperatures and sea water as well as to caustic and salt solutions. A solid solution alloy (Monel 400) that can only hardened by cold working. Monel 400 exhibits characteristics like high strength , toughness , good weldability and good corrosion resistance . Chemical Composition Monel 400 Ni63.0 min Fe1.0 – 2.5 C0.3 max Mn2.0 max Si0.5 max Cu28.0 – 34.0 Al0.50 max S0.02 max
Inconel 600 Inconel 600 is a nickel-chromiumsuper alloy. It is readily weldable and non-magnetic in nature and used in various corrosion resisting applications. The chromium content of the Inconel 600 provides resistance to weaker oxidizing environments while the high nickel content provides exceptional resistance to chloride stress corrosion cracking and a level of resistance to reducing environments . Chemical Composition Inconel 600 Ni72.0 min Cr14.0 17.0 Fe6.0 10.0 C0.15 max Mn1.0 max S0.015 max Si0.5 max Cu0.5 max
Incoloy 800,Incoloy 800H , and Incoloy 800HT are nickel-iron-chromium super alloys. When exposed to high-temperature these alloys not only provide excellent resistance to oxidation and carburization but also good strength too. These nickel steel alloys are similar except for the higher level of carbon in Incoloy 800H, and the addition of up to 1.20 percent titanium and aluminum in Incoloy 800HT. Chemical Composition Incoloy800 800H 800HT Ni30-3530-3530-35 Fe39.5 min39.5 min39.5 min Cr19-2319-2319-23 Cu0.75 max0.75 max0.75 max Ti0.15-0.600.15-0.600.25-0.60 Al0.15-0.60 0.15-0.600.85-1.20 C0.1 max 0.05-0.10.06-0.1 Mn1.5 max1.5 max1.5 max S0.015 max0.015 max0.015 max Si1.0 max1.0 max1.0 max
Inconel 625 Inconel 625 is a low carbon Nickel-chromium-molybdenum-niobium super alloy .Inconel 625 is a oxidation and corrosion resistant nickel alloy that is used both for its outstanding aqueous corrosion resistance and high strength. Inconel 625‘s outstanding toughness and strength is due to the addition of niobium which acts with the molybdenum to stiffen the alloy’s matrix. Chemical Composition Inconel 625 Ni58.0 min Cr20.0 – 23.0 Fe5.0 max C0.10 max Mn0.50 max Si0.50 max Mo8.0 – 10.0 Co1.0 max Al0.40 max Ti0.40 max Nb + Ta3.15 – 4.15 P0.015 max S0.015 max
Incoloy 825 Incoloy 825 (Nickel-Iron-Chromium alloy) with addition of copper and molybdenum .Against aqueous corrosion it has better resistance as compared to Incoloy 800, otherwise both are same .To provide exceptional resistance against many corrosive environments is how the chemical composition of Incoloy 825 is designed .Incoloy 825 is specially resistant to sulfuric and phosphoric acids. Chemical Composition Incoloy 825 Ni38.0 46.0 Cr19.5 23.5 Fe22.0 min Mb2.5 3.5 Ti0.6 1.2 Cu1.5 3.0 Mn1.0 max C0.05 max S0.03 max Al0.2 max Si0.5 max
Forged Steel Pipe Fitting: Socket Weld Forged Pipe Fittings, Threaded Forged Steel Pipe Fittings 1. Forged Fittings Type: Elbow, cross, street elbow, tee, coupling, half coupling, cap, plug, bushing, union, outlet, sage nipple, bull plug, reducer insert, pipe nipple etc. 2. Connection: Socket Welded, Threaded 3. Size Range: 1/8" - 4"(6mm - 100mm) 4. Pressure Rating: Threaded Forged Pipe Fittings: 2000LBS, 3000LBS, 6000LBS Socket welding Wog 3000, 6000, 9000 LBS 5. Specifications: 1) Standard: ASME B 16.11, MSS-SP-79\ 83\ 95\97 2) Material: ASTM A105, ASTM A182(F304, F304L, F316, F316L, F304H, F316H, F317L, F321, F11, F22, F91). 3) Size of raw material: Dia. 19-85mm round bar. 6. Technology: Forged 7. Packing: Wooden cases or wooden pallet or as per customers requirement 8. Delivery Time: 25 days after order conformed 9. Payment: By T/T or L/C 10. Applications range: Petroleum, chemical, machinery, electric power, shipbuilding, Papermaking, construction etc
Atomized spherical aluminium powder 1-2 micron for thermal interface material application 1. D50=1.5- 2 micron 2. Span: 1.5-2.0 3. Chemical content: Alâ?¥99.80%ï¼? water content: 0.01-0.1% Fe:0.06-0.09%, Si:0.03-0.08% 4. Good spherical rate 5. Strict control of the distribution 6. Quality is consitent and stable between different batches
High quality UBC can.
we are base order supply & export Bronze Propeller scraps.
Our company is a reliable marketing company here in Southern Africa and an accredited Auctioneers/License seller to the Republic of South Africa , presently we have an allocation of 120,000 M/TS of used rail from the South African railway cooperation. We are therefore, looking for serious buyers who can enter into contract with us and they will be ready to buy up to 30,000 m/t per month. Our payment terms is by T/T or LC within 14 days upon the arrival of the materials at the destination port, and our unit price is $120dollars {USD] $205 is our CIF any sea port of the world: Specification; Used Rails as GOST R50-R65 R50 (51.67KG/METER) GOST 7173-55 R65 (64.72KG/METER) GOST 8161-75 Chemical composition of the used rails scrap. MN:0.60 1.05; C:0.54 0.82; SI:0.18 - 0.12; S:0.04Max; P:0.035Max; AS:0.01% Max of Max Share; and CR: Residual - Our company is a reliable marketing company here in Southern Africa and an accredited Auctioneers/License seller to the Republic of South Africa , presently we have an allocation of 120,000 M/TS of used rail from the South African railway cooperation. We are therefore, looking for serious buyers who can enter into contract with us and they will be ready to buy up to 30,000 m/t per month. Our payment terms is by T/T or LC within 14 days upon the arrival of the materials at the destination port, and our unit price is $120dollars {USD] $205 is our CIF any sea port of the world: Specification; Used Rails as GOST R50-R65 R50 (51.67KG/METER) GOST 7173-55 R65 (64.72KG/METER) GOST 8161-75 Chemical composition of the used rails scrap. MN:0.60 1.05; C:0.54 0.82; SI:0.18 - 0.12; S:0.04Max; P:0.035Max; AS:0.01% Max of Max Share; and CR: Residual
HMS HMS1, HMS1&2 and Used rail We can supply by container base from 500 Mt And for bulk shipment from 30,000 mt direct from yard owner for small quantity and from seller mandate from big quantity So, we can offer you a competitive price Not only for HMS and Used rail but also All kind of metal scraps, petroleum product, all kind of Ore and stone, Rice and sugar. For example Cement, D2, Iron Ore, Urea, sugar, copper etc international standard
HMS stands for heavy melting scrap, and 1 & 2 are the two grades within that definition. Heavy melting steel (HMS) or heavy melting scrap, is a designation for recyclable steel and wrought iron. It is broken up into two major categories: HMS 1 and HMS 2. The difference between the two is HMS 1 does not contain galvanized and blackened steel, whereas HMS 2 does. Both HMS 1 & 2 comprise obsolete scrap only. That is iron and steel recovered from items demolished or dismantled at the end of their life. Because both grades guarantee a minimum piece thickness – at least 1/4inch (6.3mm) for HMS 1, and 1/8in for HMS 2 – consignments have a high density. Both also have defined maximum dimensions (usually 60in x 24in), and should be prepared to facilitate handling and charging to a furnace. This density, sizing and preparation makes for efficient furnace operation by minimising the time to charge enough scrap for a full melt. In contrast, thin mixed scrap greatly increases charging time, cutting furnace productivity. HMS is usually traded as a blend of 1 & 2, either a premium blend (80:20) or lower grade mixes (70:30) and (60:40). Our Products Coal Trading Company HMS Trading Company
We are Offering wide range of Metal Furniture for you in our unique selection of Metal Furniture. Metal Furniture at wholesale prices. Metal Furniture for living room, bedroom, dining room, bar furniture,Contemporary metal table and chairs, Metal Garden Furniture, Metal Bed, chairs, Metal outdoor furniture, Metal office furniture, Metal Cabinets, Metal Racks, Hospital Furniture Metal Medical Furniture, Durable Metal Furniture and more.
Copper knitted mesh is available for two main materials: one is pure copper, which contains 99% copper and the other is tinned copper, which contains 6% - 8% tin. The materials are knitted into knitted mesh. The knitted mesh can be mono-filament and multi-filament. The mono-filament is the simplest structure of knitted mesh and the multi-filament knitted mesh has higher strength and can be used in more applications. There are two types of copper knitted mesh, which are flatten copper knitted mesh and ginning copper knitted mesh. The original knitted mesh is flat, and they can be crimped according to customers' requirements to form ginning copper knitted mesh. Advantages of copper knitted mesh High strength. Firm structure. Will not scratch or mar. Never rust. Non-flammable. Resistant to disintegration. Reusable. Long service life. Applications of copper knitted mesh Copper knitted mesh can be used for industrial, for example, copper knitted wire mesh filters is used for cleaning and filtration. Our copper knitted mesh is widely used as air filters, breathers and separators made for cars, trucks and farm equipment. Copper knitted mesh can be used as knitted wire mesh shielding in cables and other applications. Copper knitted mesh can be used as filtration materials in oil, gas and water filtration applications. Copper knitted mesh can be used as knitted copper cleaning mesh for cleaning inside and outside of mechanical parts. Copper knitted mesh can be made into knitted cleaning balls or scourer to cleaning kitchenware and soldering iron. en.shstsw.com
In many leading industries Demister Pads have gained acceptance as a low cost and highly efficient means of separating Entrained liquid droplets from gas and vapour stream and we supply demister pad & mist eliminator for scrubber with high quality, the feathers as blow: By careful choice of wire diameter, knitted mesh demisters with extremely high free volumes (typically 98-99%) along with very high removal efficiencies and low pressure drop. Along with wire diameter and mesh density, another important parameter in design and operation is the vapor velocity. This can be controlled by careful selection of the mesh area. Optimal area will depend on operating temperature, pressure and pressure drop. Under normal operating conditions, 99% + removal efficiency can be achieved with a pressure drop of less than 250 Pascals. Wire Size: 0.08mm - 0.30mm flat wire or round wire. Single-strand knitted, multi-strand knitted, metal & non-metal (various fibers) knitted wires may be pressed into various specification of corrugated wire as require. Type Specification: Standard type 40-100 60-150 105-300 140-400 160-400 200-570 High-efficiency type 60-100 80-100 80-150 90-150 150-300 200-400 300-600 High-penetration type 20-100 30-150 70-400 100-600 170-560 Damping type 33-30 38-40 20-40 26-40 30-40 30-50 48-50 30-60 30-80 50-120 or according to your demands Construction materials: SUS304, 304L, SUS316, 316L, Copper, Nickel, Titanium, MONEL, P.P (Poly propylene), P.E (poly ethylene), teflon and glass fiber Packaging Details: Plastic bag inside, carton or wooden case outside. Delivery: 10-15 days after received your payments. Benefits: 1 Easy to install in all process equipment 2 Most cost-effective solution when equipment sizes are set by other requirements 3 High efficiency with low pressure drop 4 Emergency delivery available 5 ISO9001:2008 Applications: Knockout Drums, Distillation Towers, Steam Drums, Absorbers, Sulphuric acid plants, Vacuum columns, Evaporators, Disitllation and rectification plants, Oil separators and etc
In many leading industries Demister Pads have gained acceptance as a low cost and highly efficient means of separating Entrained liquid droplets from gas and vapour stream and we supply demister pad & mist eliminator for scrubber with high quality, the feathers as blow: By careful choice of wire diameter, knitted mesh demisters with extremely high free volumes (typically 98-99%) along with very high removal efficiencies and low pressure drop. Along with wire diameter and mesh density, another important parameter in design and operation is the vapor velocity. This can be controlled by careful selection of the mesh area. Optimal area will depend on operating temperature, pressure and pressure drop. Under normal operating conditions, 99% + removal efficiency can be achieved with a pressure drop of less than 250 Pascals. Wire Size: 0.08mm - 0.30mm flat wire or round wire. Single-strand knitted, multi-strand knitted, metal & non-metal (various fibers) knitted wires may be pressed into various specification of corrugated wire as require. Type Specification: Standard type 40-100 60-150 105-300 140-400 160-400 200-570 High-efficiency type 60-100 80-100 80-150 90-150 150-300 200-400 300-600 High-penetration type 20-100 30-150 70-400 100-600 170-560 Damping type 33-30 38-40 20-40 26-40 30-40 30-50 48-50 30-60 30-80 50-120 or according to your demands Construction materials: SUS304, 304L, SUS316, 316L, Copper, Nickel, Titanium, MONEL, P.P (Poly propylene), P.E (poly ethylene), teflon and glass fiber Packaging Details: Plastic bag inside, carton or wooden case outside. Delivery: 10-15 days after received your payments. Benefits: 1 Easy to install in all process equipment 2 Most cost-effective solution when equipment sizes are set by other requirements 3 High efficiency with low pressure drop 4 Emergency delivery available 5 ISO9001:2008 Applications: Knockout Drums, Distillation Towers, Steam Drums, Absorbers, Sulphuric acid plants, Vacuum columns, Evaporators, Disitllation and rectification plants, Oil separators and etc
