INTRODUCTION:
Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. Vibrant colors can be achieved by adding color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation.
FEATURE:
1.Mixed Viscocity
2.Very soft
3.Excellent temperature resistence
IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE:
Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes.
APPLICATION:
Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening.
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
For more information, welcome to contact Lilian:
Wechat / Phone: 8613617490457
E-mail: lilian(at)xrsil(dot)com
Skype: lilian-xrsilicone
Company: Dongguan Xinrun Silicone New Materials Co., Ltd / Xinrun Group Limited
Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
FEATURES:
-Mixing ratio of catalyst 2%-5%
-Good flowability
-Great self-deaeration
-Very good heat resistance
-High thermal conductivity
-Outstanding release properties
-High tear resistance
-Low shrinkage
-Outstanding resistance to inhibition
-Good resistance to polyester resin and concrete
SHELF LIFE:
When stored at or below 32°C (89.6°F) in the original unopened containers, such silicone base and its curing agents have a usable life of 12 months.
PACKAGE:
Silicone Base is available in 1Kg, 5Kg, 20Kg, 25Kg and 200Kg containers. Curing Agents are available in 50g, 1Kg and 20Kg containers.
APPLICATIONS:
-Architectural Restoration
-Sculpting/Wax Casting
-Concrete/GRC Casting
-Gypsum/Plaster Decoration
-Polyester/Resin Crafts Molding
-Furniture Molding
-Candles Mold making
-Soaps Mold making
-Tire Molding
-Detailed reproduction of figurines, art objects and similar items
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
Silicone Glass Lid/Glass Lid with Silicone Rim is a perfect fit for cookwares like pot and pan. Compared with traditional stainless rim glass lid, silicone rimmed glass lid has advantages like:
* Dishwasher safe
* Shattered-proof and protect both the lid and floor
* More color options that go with the pot color
* Heat resistant
* Universal size lid can fit in 3 size pots
* More stylish and elegant
* Better sealing
Description of liquid silicone for soft relief gel insoles :
OTT-X710 Liquid Silicone for Insoles is a solvent-free, flowable 2 Component RTV Silicone rubber. After mixing the X710 A and X710 B at a mix ratio of 1:1 the material will cure by an addition reaction at room temperature. The cure rate can be accelerated significantly by heat. Material has been especially developed for insoles.
Application of liquid silicone for soft relief gel insoles :
OTT-X710 silicone rubber is specially developed for insoles. It can also be used for lace coating and Conveyor belt coating and also for other applications where fast cure at elevated temperatures and good flow or self leveling characteristics are required.
Using instructions of liquid silicone for soft relief gel insoles:
1. Applicable to the injection molding process
2. Mixing component A with B evenly according its mix ratio, it is ready for use after degassing, it cures by heating up the temperature when pouring into the mold.
3. The curing time is subject to the temperature, short time will be required under high temperature, long time will be required while the product with large thickness.
1. Pure silicone rubber, anti-oil and waterproof
2. Temperature resistance from -60~260 Celsius degree
3. Anti-aging, Ozone resistance, Insulating
4. No corrosion from copper and silver and so on.
1.Environmentally friendly non-toxic, in line with the ISO/ASTM
2.High tear resistance, low shrinkage, good resistance to anti-aging performance.
3.Generally used in medical equipment, home appliances, aerospace, military,
4.Automobile manufacturing, electronic components, transformers, motors, etc
119196 Metal Metal Products Suppliers
Short on time? Let Metal Metal Products sellers contact you.
Features of OTT Low Price Moulding Liquid Silicone Rubber:
An exceptional fluidity and good operability, easy to demold
Good tensile strength and tear strength
Soft hardness
Copy detailed pattern
Good flexibility
Eco-friendly
Long shelf-time &lifetime
Applications of OTT Low Price Moulding Liquid Silicone Rubber:
OTT Low Price Moulding Liquid Silicone Rubber could be mainly used for PU/poly resin products, unsaturated resin products, plaster products, fiberglass products, gypsums crafts, cement statues, etc.
Feature of silicone rubber thermal conductive insulation pad
High compressibility, soft and flexible
Natural stickiness, no extra surface frontal adhesives
Good thermal conductivity,
Meet with rohs standard
High thermal conductivity
High conformability to uneven surfaces at low stress application
Electrical isolating very cost effective
Application of high quality silicone rubber thermal conductive insulation pad
1. Heat sink your cpu/gpu
2. Switching power supply
3. Video equipment
4. Mobile equipment
5. Communication equipment
6.Between semiconductor/magnetic components and heat sinks.
Packing details : packing, solid bicycle saddle, 50pcs/carton
Delivery details : 3-30 days after order of solid bicycle tire tubes
1) Applications:
OTT mold making liquid silicone rubber for plaster mold is primarily intended for poly resin crafts, PU crafts, PU resin crafts, gypsum crafts, unsaturated resin crafts, lighting and candles crafts , plastic toy, stationery gifts crafts industry, a large statue Buddha, relief, furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe componentfactory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
2) Description:
OTT mold making liquid silicone rubber for plaster mold is white or red flowing liquid with general hardness of 22-50A after curing. Molding silicone is a kind elastic silicone which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength, tears strength and elongation.
Liquid RTV Molding Silicone Rubber raw material for all kinds of mold making
Features of liquid RTV Molding Silicone Rubber raw material for all kinds of mold making:
1. Two part of liquid fluid: liquid white silicone and curing agent.
2. Cure at room-temperature within 4-8 hours, but all performance will act perfectly when it cure within 2 - 4 hours.
3. Good fluidity and excellent operation.
4. Good resistance to weather, temperature, aging, acid.
5. Excellent tear strength, comfortable duplication times.
Application of liquid RTV Molding Silicone Rubber raw material for all kinds of mold making:
1.Resin crafts, unsaturated resin crafts
2. Poly resin crafts, candle crafts, plastic crafts
3. Making molds forgypsum,GRC,concrete,Artificial stone products molding,Wax casting
4.Decoration building mold making
5.Lighting & candles crafts,stationery gifts,crafts industry
6.Casting for Statue,Buddha, Christmas ornaments,sculptures, figures etc
Operation Instruction for Liquid RTV Molding Silicone Rubber raw material for all kinds of mold making :
RTV-2 liquid mold silicone rubber is a kind of flowing liquid, and it consists of two component, part a is a flow-able liquid silicone rubber, part B is the curing agent.
1. Firstly, after your previous work of dealing with the original model, take some liquid silicone rubber, add 2%~3% cuing agent of the amount of silicon and mix themevenly.
2. Then after vacuum-pumping the mixture, you can pour it into the mold frame.
3. The silicone mold will cured in 2~3 hours.
Note: the time for vacuum-pumping should be less than 3-5mins, otherwise, once the silicone rubber has cross-link reaction during vacuum. it will not be operated.
Introduction of liquid rtv silicone for electronic patrs sealing
liquid rtv silicone for electronic patrs sealing is a two-component room temperature cure potting compound with mix ratio of 1: 1, curing time can be accelerated by heating up, features with good flow ability and flame resistance. It's suitable for encapsulating of LED displayers, power module and electronics components, etc.
Features of liquid rtv silicone for electronic patrs sealing
Easy mix with 1: 1 proportion
Low viscosity, good flow ability
Room temperature cure or heat up cure
Thermal conduction, flame resistance
Without solvent
Using Instructions of liquid rtv silicone for electronic patrs sealing
1. Preparing: Clean up the coating surface, remove the rust, dust, oil dirt.
2. Pouring: Weigh the silicone and catalyst correctly, mix silicone part A and part B thoroughly, pour onto the electronic components/surface after vacuum degassing.
3. Curing: Room temperature cure or heat-up cure is both workable.
4. It should be use up after open the package, the material must be kept in a cool place sealed well, and it should avoid from contact with moisture in the air.
Packaging of liquid rtv silicone for electronic patrs sealing
Packs are available in 20kg and 200kg per drum.
Storage & Transportation of electronic potting compound silicone rubber
1. Keep it from strong sunshine, heat, and store in cool & dry place, well sealed. It has a shelf life of 12 months.
2. It can be stroked and transported as non-dangerous goods.
Technical guidelines of liquid rtv silicone for electronic patrs sealing :
1. Pls put part A and part B in separate container and stir evenly before mixing the two part\ together.
2. Weight Ratio: part A: part B = 10:1
3. Deaeration the mixture under 0.08 MPa for 3 minutes.
4. The temperature influences the curing time of electronic potting silicone rubber.
5. When in too low temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization.
Warm tips for liquid rtv silicone for electronic patrs sealing :
1. The electronic potting silicon rubber should be sealed storage.The mixture should be used up at
once, avoid causing waste.
2. The electronic potting silicone rubber belongs to non-dangerous goods, but keep away from
mouth and eyes.
3. When electronic potting silicone rubber gets stratified after a period of storage, Please mix the
electronic potting silicone rubber evenly before using, it does not affect the performance
Description of RTV Silicone for PCB board electronic-pouring:
RTV Silicone for PCB board electronic-pouring is a room temperature/heating curing and molding organic silicone materials. This kind of two-component elastic silicone potting, designed to protect in harsh conditions of electronic products.
silicon encapsulating glue used new technology without heating can cured, would be curing. When used according to 100:10 (weight ratio or the volume in the thorough mixing proportion of A and B two components, products will be in A certain time, form of the elasticity of curing buffer material.
RTV Silicone for PCB board electronic-pouring characteristics:
Easy mix with 1: 1 proportion
Low viscosity, good flow ability
Room temperature cure or heat up cure
Thermal conduction, flame resistance
Without solvent
Using Instructions of RTV Silicone for PCB board electronic-pouring:
1. Preparing: Clean up the coating surface, remove the rust, dust, oil dirt.;
2. Pouring: Weigh the silicone and catalyst correctly, mix silicone part A and part B thoroughly, pour onto the electronic components/surface after vacuum degassing.
3. Curing: Room temperature cure or heat-up cure is both workable.
4. It should be use up after open the package, the material must be kept in a cool place sealed well, and it should avoid from contact with moisture in the air.
Storage & Transportation of two parts silicone for led screen potting compound:
1. Keep it from strong sunshine, heat, and store in cool & dry place, well sealed. It has a shelf life of 12 months.
2. It can be stroked and transported as non-dangerous goods.
Application of RTV2 Footcare Liquid Silicone For Shoe Insoles Making:
Footcare Liquid Silicone OTT-X705 is widely used for Silicon Insole, Silicone Gel Toe Spreaders, Silicone Gel Arch Supports, Silicone Gel Metatarsal Pad, silicon pads, Silicone Gel Heel Cups, etc.
Storage and Precautions of RTV2 Footcare Liquid Silicone For Shoe Insoles Making:
silicone rubber liquid is an environmentally-friendly liquid silicone product, is not easy to burn and can be stored and transported as non-hazardous goods. The shelf life of the product is about one year from the date of production. Inspection is required when exceeding the time limited. It can continue to be used in case of neither thickening nor deterioration.
1.Description of liquid silicone rubber
C830 Silicone rubber is condensation cure silicone rubber for mold making. The silicone rubber will be cured under room temperature, It’s two-components, the mixing ratio is 100:2 . Part A is a flowable liquid silicone , part B is the catalyst. It has an exceptional fluidity and good operability. C-830 tin cure mold silicone has a good property , it is suitable for various mold making .
2.Characteristics of liquid silicone rubber
*An exceptional fluidity and good operability, easy to demold
*Good tensile strength and tear strength
*lower shrinkage
*non-deformation ,non-oily
*good flexibility
*eco-friendly
*long shelf-time &lifetime
C830 Silicone rubber is mainly suitable middle sized product and big size with simple pattern.
Package:
1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum based on vacuum packing.
Shelf life and transportation
1. Twelve(12) months when stored at 25C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
1.Description of Platinum liquid silicone rubber for mold making
G830 Silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fast by heating, It’s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible.
2.Characteristics of Platinum liquid silicone rubber for mold making
*An exceptional fluidity and good operability
*Good tensile strength and tear strength
*Food grade silicone rubber
*high temperature resistance
*good flexibility
*No smell ,non-toxic
*long shelf-time &lifetime
*Lower shrinkage
3.Application of Platinum liquid silicone rubber for mold making
G830 silicone rubber is flexible silicone rubber ,it has a higher temperature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing .
4.Datesheet of Platinum liquid silicone rubber for mold making
Item No. Appearance Hardness (shore A°) Viscosity (CPS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25? ) Curing time( 25 ?) shrinkage
G830 translucent 30±2 7000±1000 =55 =24 =450 1:1 20-30 mins 2~3 h =0.1%
Packing:
20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B
25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B
200KG/drum packing for part A +200KG/drum packing for part B
1. Description of food grade liquid silicone rubber for making mould
Addition-curing, Food grade, Translucent, Two-component mold making silicone.
2. Characteristics of food grade liquid silicone rubber for making mould
Acceptable for food contact
Outstanding release properties
Low viscosity
Easy mixing and degassing
High flowability
Odorless and Nontoxic
Enhanced durability
3. Application of food grade liquid silicone rubber for making mould
Food Grade Related Applications
Cake mold
Chocolate moldmaking
Candy moldmaking
Baking moldmaking
Ice trays molding
Casting butters
Casting for Kitchen products
5. Using instructions of food grade liquid silicone rubber for making mould
Step 1: Prepare and clean the prototype.
You must make sure your original molds perfect, fix the original mold on a board, then using some assistant material (like cardboard) to make a frame for to surround the prototype. The frame is no need, if we make the mold by brushing way.
Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone : catalyst= 100:2), mix the silicone rubber and catalyst evenly.
Notes: rtv silicone rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicone rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finishes molds will have a short life. All of these will cause a waste of silicone rubber.
Step 3: Vacuum pumping.
After mixed the silicone evenly, it is better to release the bubble by vacuum pumping.
Step 4: Pouring cast or brushing cast.
After released the bubble, we can pour/brush the silicone rubber on the prototype.
Notes: Please finishes all the steps within the operation time. If not, it will cause cross linking reaction, and no more further steps will be available. So, we have to pay attention to the pot life and curing time.
Packaging & Shipping
Packing:
20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B
25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B
200KG/drum packing for part A +200KG/drum packing for part B
1.Description of life casting rtv-2 silicone rubber for prosthetic hands
RT-810 silicone rubber is platinum cure silicone rubber with medical grade , it belong to be life casting silicone rubber. The silicone rubber will be cured under room temperature and can be cured under room temperature and can be fastly by heating. It's two components liquid silicone rubber, the mixing ratio is 1:1. It has an exceptional fluidity and good operability. Especially, the platinum cure silicone rubber has a lower shrinkage, higher temperature resistance
G810 is extremely soft as a real feeling as humman skin
2.Characteristics of life casting rtv-2 silicone rubber for prosthetic hands
*An exceptional fluidity and good operability
*Good tensile strength and tear strength
*Food grade silicone rubber
*high temperature resistance
*good flexibility
*No smell ,non-toxic
*long shelf-time &lifetime
*Lower shrinkage
3.Datesheet of life casting rtv-2 silicone rubber for prosthetic hands
Item
No. Hardness
(A°) Viscosity
(CS) Tensile-strength
( kgf /cm2 ) Tear-strength
(kgf /cm2 ) Elongation-break(%) Mixing
ratio operation time (25 ? ) Curing time ( 25 ?) shrink-age
RT-810 10 5000 40±5 10±2 450±50 1:1 20-30 mins 2~3 h =0.1%
Notice of life casting silicone for prosthetic limbs
RT-810 life casting silicone rubber is platinum cure silicone , which is very easy to cause cure inhibition , so
please do remember thoroughly clean the model and tool before operation . Besides , please avoid the condensation silicone rubber (100:2) contact or mix with the following material , otherwise the silicone won’t be cured :
1. Liquid condensation silicone ( condensation silicone not completely cured or organic tin compounds )
2. Sulphur, sulfide and sulfur rubber materials.
3. Amine compounds as well as contains the amine materials.
4. Pewter solder flux.
Packaging & Shipping
Packing:
20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B
25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B
200KG/drum packing for part A +200KG/drum packing for part B
1. Description of rtv 2 liquid silicone rubber for frame gypsum molds
C830 silicone rubber is condensation cure silicone rubber (tin cure silicone rubber) for mold making. The silicone rubber will be cured under room temperature. It's two components, the mixing ratio is 100:2. Part A is a flowable liquid silicone, part B is the catalyst. It has an exceptional fluidity and good operability.
2. Characteristics of rtv 2 liquid silicone rubber for frame gypsum molds
* An exceptional fluidity and good operability, easy to demold
* Good tensile strength and tear strength
* Suitable hardness
* Copy detailed pattern
* Good flexibility
* Eco-friendly
* Long shelf-time &lifetime
3. Application of rtv 2 liquid silicone rubber for frame gypsum mold
C830 liquid silicone rubber is perfect molding material, it is suitable to make mold for concrete casting, artificial stone, brick, cement casting, gypsum decorations, plastic product, resin craft, polyester, polyurethane, bronze casting, statues, jewelry, wax, crystal, tire mold, shoe mold, clay casting, ceramic casting. etc.
C830 liquid silicone rubber is mainly suitable for small or middle sized products with delicate pattern by pouring and brushing operation.
Shelf life and transportation
1. Twelve(12) months when stored at 25C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
Feature of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose
1. Pure silicone rubber, anti-oil and waterproof
2. Temperature resistance from -60~260 Celsius degree
3. Anti-aging, Ozone resistance, Insulating
4. No corrosion from copper and silver and so on.
Application of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose
1.Environmentally friendly non-toxic, in line with the ISO/ASTM
2.High tear resistance, low shrinkage, good resistance to anti-aging performance.
3.Generally used in medical equipment, home appliances, aerospace, military,
4.Automobile manufacturing, electronic components, transformers, motors, etc...
119196 Metal Metal Products Suppliers
Short on time? Let Metal Metal Products sellers contact you.
