Housing Electrical
Electrical board hinged IP31. Designed for assembly of electrical boards using modular equipment. Electrical board built-in IP31. Designed for assembly of electrical boards using modular equipment.
VIBRATION CONNECTORS MANUFACTURERS & SUPPLIERS Stainless steel vibration eliminator: Aeroflex Vibration eliminators are specially designed to absorb mechanical vibration and destructive force of noise which is transmitted by the compressor, and also eliminate the stresses linked with piping thermal expansion in refrigeration and air condition installation. These connectors are TIG welded stainless steel hose with copper pipe, due to there is not any brazing so these connector bear more temperature as compared to brazed fitting The main function of vibration eliminator is to absorb compressor vibration and stop its transition into pipe network, by isolating the vibration the risk of damage to pipe work and related component reduce, 1.1 Size range of vibration eliminator: The comprehensive range of vibration eliminator are available from to 3 1/8 Outer diameter of copper tube, copper tube are comply a per ASTM B88 & ASTM B88M (water & general plumbing system) & ASTM B280 (air conditioners & refrigeration system) 1.2 Material specification: Aeroflex Vibration eliminators are manufacture from EN 10028-7, Stainless steel SS 321 & SS 316L annular corrugated hose with SS 304 stainless steel braid. All unit are brazed with copper tube, detail dimension of pipe and vibration connector are in the table. All the units are ultrasonically cleaned and completely dried made suitable to refrigeration system Individual package of connector are remain under sealed plastic tubing. The maximum test pressure is 1.5 time of maximum operating pressure and minimum burst pressure is 5 time of maximum operating pressure. Copper tube end are designed as sweat connection for refrigeration tubing which have inner surface as per ASME B16.18 1.3 Installation conditions: Aeroflex vibration eliminator should be installed as close as possible to the compressor and end away from the source of vibration. Vibration eliminator should be installed perpendicular to the direction of vibration (in-line with the compressor crank shaft) Horizontal Vibration: Where source of vibration is only in the horizontal plane, a single vibration and noise eliminator may be installed. Best results will be achieved by installation at 90�° to the source which is normally the crank of the compressor in a horizontal plane. See fig. 1 Vertical / horizontal vibration: Where the source of vibration and noise is in both horizontal are in vertical planes. Best result will be achieved by installing two vibration eliminators at right angle to each other see fig. 2 Although the copper tube end of vibration absorber are attached by TIG welding (special alloy filler) during installing if unit is over heated there is not effect on the connector
Field installation connector also be called Fast install connector is a new kind of connector that could be used in FTTH project scene. They donot need to polishing, no epoxy. They could be installed in the field and make connection less than two minutes. Of course, It donot need fused the fiber. Just some little tools enough, so it could save time and cost. Connector Type : SC Polishing : UPC and APC Ferrule : Ceramic V-Groove : Plastic Material Cable Diameters : 2x3mm FTTH Drop Cable;1.6x2.0mm FTTH Drop Cable Length : 51mm Insertion Loss : 0.3dB(typical);0.5dB(Max) Return Loss : UPC 40dB;APC 50dB Tension Strength : 30N Operating Temp : -40 C~+75 C
Fast installation connector also be called Field install connector is a new kind of connector that could be used in FTTH project scene. They don't need to polishing, no epoxy. They could be installed in the field and make connections less than two minutes. Of course, It donot need fused the fiber. Just some little tools are enough, so it could save time and cost. Part No. : J-P-SSA-50 Connector : SC APC Ferrule : Ceramic V-groove : Plastic material Cable Diameters : 2.0/3.0mm Simplex cable;2x3 FTTH Drop Cable Dimension : 50mm Insertion Loss : 0.3dB(typical); 0.5dB(Max) Return Loss : UPC 40dB;APC 50dB Tension Strength : 50N Operating Temperature : -40 C~+75 C
Material: Zinc Alloy, Size: 3/8",1/2", 3/4",1",1-1/2", 2", 3",4". Fit for liquid tight flexible conduit.
1. 8 channels of sending, 8 channels of reception; 2. Receive and add current system time; 3. Timing transmission and data can be updated at any time; 4. Receive labeled filtering and interrupt receiving; 5. The baud rate can be set to 10K, 12.5K, 48K, 50K, 100K, 150K; 6. FIFO reset function of sending and receiving, set to receive enable signal; 7. Send FIFO including 511x32BIT , and receive FIFO including (1M-1) Ã?32BIT 8. Standard ARINC429 data format, receiving and sending can be set separately; Product Description: ZY32208/32308 interface module which researched and developed according to ARINC429 Bus Communication Agreement is based on buses PXI/CPCI/PCI. The data can be updated at any time, and the word interval, message interval, the predetermined quantity of transmitting messages and the quantity of sent messages can be set up. The modules SCSI-68-pinhole connector makes it easy to operate. The powerful functions of this module can meet users communication testing requirements, and the excellent compatibility is available to all types of system configurations. Performance Parameters: Quantity of Transmitting channel: 8; Quantity of receiving channel: 8; Baud rate: 10K/12 5K/48K150K/100K/150K; Send FIFO: 511Ã?32BIT; Receive FIFO: (1M-1)Ã?32BIT; General Specifications: External dimensions (LÃ?WÃ?H): Standard PXI/CPCI3U card 160mmÃ?100mmÃ?4HP, tolerance
1. 8 channels of sending, 8 channels of reception; 2. Receive and add current system time; 3. Timing transmission and data can be updated at any time; 4. Receive labeled filtering and interrupt receiving; 5. The baud rate can be set to 10K, 12.5K, 48K, 50K, 100K, 150K; 6. FIFO reset function of sending and receiving, set to receive enable signal; 7. Send FIFO including 511x32BIT , and receive FIFO including (1M-1) Ã?32BIT 8. Standard ARINC429 data format, receiving and sending can be set separately; Product Description: ZY32208/32308 interface module which researched and developed according to ARINC429 Bus Communication Agreement is based on buses PXI/CPCI/PCI. The data can be updated at any time, and the word interval, message interval, the predetermined quantity of transmitting messages and the quantity of sent messages can be set up. The modules SCSI-68-pinhole connector makes it easy to operate. The powerful functions of this module can meet users communication testing requirements, and the excellent compatibility is available to all types of system configurations. Performance Parameters: Quantity of Transmitting channel: 8; Quantity of receiving channel: 8; Baud rate: 10K/12 5K/48K150K/100K/150K; Send FIFO: 511Ã?32BIT; Receive FIFO: (1M-1)Ã?32BIT; General Specifications: External dimensions (LÃ?WÃ?H): Standard PXI/CPCI3U card 160mm100mm 4HP, tolerance
1. 8 channels of sending, 8 channels of reception; 2. Receive and add current system time; 3. Timing transmission and data can be updated at any time; 4. Receive labeled filtering and interrupt receiving; 5. The baud rate can be set to 10K, 12.5K, 48K, 50K, 100K, 150K; 6. FIFO reset function of sending and receiving, set to receive enable signal; 7. Send FIFO including 511x32BIT , and receive FIFO including (1M-1) 32BIT 8. Standard ARINC429 data format, receiving and sending can be set separately; Product Description: ZY32208/32308 interface module which researched and developed according to ARINC429 Bus Communication Agreement is based on buses PXI/CPCI/PCI. The data can be updated at any time, and the word interval, message interval, the predetermined quantity of transmitting messages and the quantity of sent messages can be set up. The modules SCSI-68-pinhole connector makes it easy to operate. The powerful functions of this module can meet users communication testing requirements, and the excellent compatibility is available to all types of system configurations. Performance Parameters: Quantity of Transmitting channel: 8; Quantity of receiving channel: 8; Baud rate: 10K/12 5K/48K150K/100K/150K; Send FIFO: 51132BIT; Receive FIFO: (1M-1)32BIT; General Specifications: External dimensions (LWH): Standard PXI/CPCI3U card 160mm100mm4HP, tolerance
Brief introduction ¦ contacts: 2~18, 28, 38, 48, 52 pins. ¦ twist pin contact, high density interconnection ¦ buckle connector, can be locked and separate quickly And avoid mis-operation. ¦ light weight, suitable for harsh environment application. ¦ the sectional area of cable core: 0.1 sq.Mm~ 0.15 sq.Mm ¦ standard: mil-c-83513
Designed for military and commercial use where upper frequency, microwave applications are necessary. Sunkye rf/microwave connectors provide excellent electrical and environmental performance characteristics.
Product name Yamaha 3p to obd-16p f Insulation resistance Rohs/ reach compliance Yes According to the cable length
Material: Insulator: thermal plastic, ul94v-0 Contacts: copper alloy Shell: copper alloy Contact plating: Underplate: 50 to 100ì-inch nickel Contact area: 1 to 30ì-inch selective gold Solder tails area: 100 to 200ì-inch tin/(lead-free) Electrical: Operating voltage: 40v Current rating: 0.5a minimum Contact resistance: 10m ohms maximum Insulation resistance: 100m ohms minimum at 500v dc Dielectric withstanding voltage: 500v ac/min Operating temperature: -20 to 85¡ãc Mating cycles: 5, 000 insertions 2400pcs/box
D-sub metal hood/cover/housing Brand/series,Zechao Cable exit angle,Straight / right angle/45 degree Pin count,9.15.25.37.50p Material, backshell,Die-cast metal ¡,zinc alloy¡ê,169; Color,Gun black (black nickel), pearl nickel, bright pearl nickel.Imitation gold;chrome Special features,Emi/rfi shield, grommets Characteristic of products,Pro-environment not easily embroidery, not changeful form stable performance; Screws,Short screw thread 4-40 unc Jack screw thread 4-40 unc Product certification,Rohs Product use,Computer, communication, medical equipment, cable, aviation, digital, machinery and equipment, game, etc Descriptions Easy to assemble db15/hd26 two piece metal backshells are a great choice for the "do it yourself" consumer. Die cast zinc alloy construction is practically indestructible and offers maximum protection against harmful emi/rfi. When used with shielded cable, a complete ground can be made between connector shells. According to the customer's request to die sinking, price concessions, the manufacturers, factory direct sale. Applications Serial data transmission data networks Instrument control device management Packing instruction Bulk or single packaged units Plastic bags points set with inner packing carton packing. Plastic bag packing Packaging according to customer's design Plastic bag sleeve packaging with carton packaging.
1.Material zinc 2 plating gold/nickel/tin 3.Support oem&odm 4.Compliant rohs 5.D-sub metal 90 standard + sl backshells,
D-sub metal hood/cover/housing Brand/Series,Zechao Cable Exit Angle,Straight / Right Angle/45 degree Pin count,9.15.25.37.50P Material, Backshell,Die-Cast Metal ,Zinc Alloy,169; color,gun black (black nickel), pearl nickel, bright pearl nickel.Imitation gold;chrome Special Features,EMI/RFI Shield, Grommets Characteristic of products,pro-environment not easily embroidery, not changeful form stable performance; Screws,Short screw Thread 4-40 UNC Jack screw Thread 4-40 UNC Product certification,ROHS Product use,computer, communication, medical equipment, cable, aviation, digital, machinery and equipment, game, etc Descriptions Easy to assemble DB15/HD26 two piece metal backshells are a great choice for the "do it yourself" consumer. Die cast zinc alloy construction is practically indestructible and offers maximum protection against harmful EMI/RFI. When used with shielded cable, a complete ground can be made between connector shells. According to the customer's request to die sinking, price concessions, the manufacturers, factory direct sale. Applications Serial data transmission Data networks Instrument control Device management packing instruction Bulk or single packaged units plastic bags points set with inner packing carton packing. 1.material zinc 2 plating gold/nickel/tin 3.support OEM&ODM 4.compliant ROHS 5.D-Sub Metal 90 Standard + SL Backshells,
D-sub metal hood/cover/housing Brand/series,Zechao Cable exit angle,Straight / right angle/45 degree Pin count,9.15.25.37.50p Material, backshell,Die-cast metal,zinc alloy¡,169; Color,Gun black (black nickel), pearl nickel, bright pearl nickel.Imitation gold;chrome Special features,Emi/rfi shield, grommets Characteristic of products,Pro-environment not easily embroidery, not changeful form stable performance; Screws,Short screw thread 4-40 unc Jack screw thread 4-40 unc Product certification,Rohs Product use,Computer, communication, medical equipment, cable, aviation, digital, machinery and equipment, game, etc Descriptions Easy to assemble db15/hd26 two piece metal backshells are a great choice for the "do it yourself" consumer. Die cast zinc alloy construction is practically indestructible and offers maximum protection against harmful emi/rfi. When used with shielded cable, a complete ground can be made between connector shells. According to the customer's request to die sinking, price concessions, the manufacturers, factory direct sale. Applications Serial data transmission data networks Instrument control device management Packing instruction Bulk or single packaged units Plastic bags points set with inner packing carton packing. 1.Material zinc 2 plating gold/nickel/tin 3.Support oem&odm 4.Compliant rohs 5.D-sub metal 90 standard + sl backshells
D-sub Metal Hood/cover/housing Brand/series : Zechao Cable Exit Angle : Straight / Right Angle/45 Degree Pin Count : 9.15.25.37.50p Material, Backshell : Die-cast Metal ¡ê¡§zinc Alloy¡ê© Color : Gun Black (black Nickel), Pearl Nickel, Bright Pearl Nickel.Imitation Gold;chrome Special Features : Emi/rfi Shield, Grommets Characteristic Of Products Pro-environment Not Easily Embroidery, Not Changeful Form Stable Performance; Screws Short Screw Thread 4-40 Unc Jack Screw Thread 4-40 Unc Product Certification Rohs Product Use Computer, Communication, Medical Equipment, Cable, Aviation, Digital, Machinery And Equipment, Game, Etc Plastic Bag Packing Packaging According To Customer's Design
0.8mm, 1.0mm, 1.27mm, 2.0mm, 2.54mm femal header with single row, dual row Insulator:lcp, ul 94v-0 Terminal:copper alloy Plating:gold plated Tape&reel
1)type:straight, right angel, smt 2)insluator body: pbt, ny6t, ny9t, lcp 3) pin material: phosphor bronze, brass 4) plating: full gold, full tin, selective plating Tube, tray
