SPM Type Plug Valve Repair Kit Fig 1502 Interchangeability Parts code:4L11769 and 4L11982,etc KUOFU have 1" 2" and 3" size Plug valve repair kits,can be provided for standard service, or low temperature and sour gas condition. These repair kits are replaceable and interchangeable for Weir SPM Valve repair kits, which is including plug, seal segment, side segment, elastomer seals, and grease fittings
Valve Seat Puller & Claw, which is a hydraulic device. The connecting screw thread between leading screw and claw is API Standard and it can be exchangeable. Claw is manufactured by ASTM1066 and has 3 armed, 4 armed and full open type, which is suitable for the size of API-5#,API-6#,API-7#,API-8# valve seat. Hydraulic valve seat puller is a removal service tool in a mud pump. The hydraulic valve seat puller is used to take installed mud pump valve seat out of mud pump fluid end module, during the process of replacing the valves seat or mud pump maintenance. At the same time, eliminate damage to fluid end expendables caused by removing valve seat with a cutting torch. Material: Full-threaded rod, claw head is 35CrMo forged. Hydraulic Valve Seat Puller Mud pump valve seat puller consists of oil cylinder, hydraulic hand pump with pressure gauge, all thread rod, puller claw etc. This tool is more effective to finish the maintenance and mud pump repair work with fewer manpower and shorter time. Advantage: simple structure, easy to use, can save a lot of manpower and time, and cost-effective.
Specification Size: 1â?? Plug Valve Low Torque (1 x 1) Male x Female FIG1502 1â?? Plug Valve Low Torque (1 x 2) Male x Female FIG1502 2â?? Plug Valve Low Torque (2 x 2) Male x Female FIG1502 3â?? Plug Valve Low Torque (3 x 3) Male x Female FIG1502 Cold working pressures: 42Mpa (6000Psi), 70Mpa (10000Psi), 105Mpa (15000Psi). Connection type: hammer union (Fig.602, Fig.1002, Fig.1502 MXM, MXF, and FXF), LP female thread and LP external thread and the plug valve with bottom base can be designed upon the clientâ??s request. Plug Valve Repair Kit Interchangeability Plug valve repair kits can be provided for standard service, or low temperature and sour gas condition. These repair kits are replaceable and interchangeable for Weir SPMâ?¢, FMCâ?¢ 2â?? and 3â?? DR plug Valve, which is including plug, seal segment, side segment, elastomer seals, and grease fittings How to contact us?
Model F Plunger Type Float Valve 1F2R-5F6R for Assembly Model F The Model F Float Valve is a plunger-type float valve that provides a positive instantaneous shut off,providing constant fluid control while drilling,The model F is a reliable and the most economical selection under standard drilling operations. Model G Flapper Type Float Valve 2F3R-5F6R for Assembly Model G The Model G is a flapper-type float valve that,when opened ,offers unrestricted bore through the float valve.The uniquely designed flapper closes rapidly to prevent cutting from entering the drill string when circulation stops and also assists primary BOP equipment in maintaining internal pressure control. Model FA Plunger Type Float Valve 1F2R-5F6R for Assembly Model FA The Model FA Float Valve has a special port running through the plunger of the float valve,This valve is used when monitoring the bit head for gas pressure and allowing differential pressure measuring when required .The port also permits partial automatic fill during run Model GA Flapper Type Float Valve 2F3R-5F6R for Assembly Model GA The Model GA Float Valve is indistinguishable from the Model G with the exception of a tungsten-cabide insert in the flapper valve,The insert has a quarter-inch orifice through the center that allows for differential pressure monitoring .The port also permits partial automatic fill during run in .
The novel valves Pvt. Ltd. is the manufacturer of Double Block and Bleed Ball Valve in India. It's used in chemical, water, petroleum, and other industries.
TRIPLE OFFSET TYPE BUTTERFLY VALVES Bonny Valve has very extended experience in manufacturing of Triple Offset Butterfly Valves Size: 2 up to 80 (DN50 up to DN2000) Pressure Rating: ASME 150#,300#,600# Materials: Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Wafer,Lugged, Flanged RF, RTJ, FF Operator : Lever, Gear Operated Specification: Design API609 / ASME B16.34 Face to Face API609 / ASME B16.10 End Flange ASME B16.5 Test API598 Special NACE MR-0175 Features: Triple Offset Type Locking Device Optional
CONCENTRIC TYPE BUTTERFLY VALVES Bonny Valve has very extended experience in manufacturing of Concentric Butterfly Valves Size: 2 up to 80(DN50 up to DN2000) Pressure Rating: ASME 150#,PN10/16 Materials: Cast Iron,Ductile Iron,Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. Seat:EPDM, NBR, PTFE End Connection: Wafer,Lugged, Flanged RF, RTJ, FF Operator : Lever, Gear Operated Specification: Design API609 Face to Face API609 / ASME B16.10 End Flange ASME B16.5 Features: Concentric Type Disc Locking Device Optional
TRUNNION MOUNTED BALL VALVES Bonny Valve has very extended experience in manufacturing of Trunnion Mounted Ball Valves Size 2" to 48"(DN50 to DN1200) Pressure Rating: ASME 150#, 300#, 600#, 900#, 1500#, 2500# Materials: Forging and Casting Type Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. Seating: Soft Seated (PTFE/RPTFE /PEEK/NYLON/DEVLON) and Metal Seated End Connection: Flanged FF/RF/RTJ, BW Ends Operator: Lever/Wrench, Gear Operated Specification: Design API 6D / API 608 / BS5351 / ASME B16.34 Face to Face ASME B16.10/API 6D End Flange ASME B16.5 BW End ASME B16.25 Test API598/API 6D Fire Safe Test API607/API6FA Special NACE MR-01-75 Features: Bolted Body Two Piece / Three Piece Bore Type Reduced Bore or Full Bore Anti-Static Device Blow-Out Proof Stem Fire Safe Design Emergency Sealant Injector Double Block and Bleed
Bonny Valve has very extended experience in manufacturing of Floating Ball Valves Size ½ inch up to 10 inch (DN 15 up to DN 250) ½" to 10" 150# ½" to 8" 300# ½" to 4" 600# ½" to 1 ½" 900#, 1500# & 2500# Pressure Rating: ASME 150# to 2500# Materials: Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. Seating: Soft Seated (PTFE/RPTFE /PEEK/NYLON/DEVLON) and Metal Seated End Connection: Flanged RF/RTJ, BW, FNPT & SW Ends Operator: Lever/Wrench, Gear Operated Specification & Standards: Design API 6D / API 608 / BS5351 / ASME B16.34 Face to Face ASME B16.10 End Flange ASME B16.5 BW End ASME B16.25 Test API598/API6D Fire Safe Test â API607/API6FA Special NACE MR-01-75 Features: Two Piece or Three Piece Bore Type Reduced Bore or Full Bore Anti- Static Device Blow- Out Proof Stem Fire Safe Design Low Emission
Bonny Valve has very extended experience in manufacturing of Forged Swing/Piston Type Check Valves Size: ½ inch up to 2 inch (DN15 up to DN50) Pressure Rating: ASME 150LB to 2500LB Materials: Forged Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Flanged RF, FF, RTJ, BW, NPT, SW Ends Specification: Design API602 / BS5352 / ASME B16.34 End Flange ASME B16.5 BW End ASME B16.25 SW End ASME B16.11 Screwed Ends ASME B1.20.1 Test API598 Special NACE MR-01-75 Features: Bolted Cover , Welded Bonnet or Pressure Seal Bonnet Full port or Conventional Port Swing or Piston Disc
Bonny Valve has very extended experience in manufacturing of Cast Swing Type Check Valves Size: 2 inch up to 60 inch (DN50 up to DN1500) Pressure Rating: ASME 150LB,300LB,600LB,900LB,1500LB, 2500LB Materials: Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Flanged RF, FF, RTJ, BW Specification: Design BS 1868 / API 6D / ASME B16.34 Face to Face ASME B16.10 End Flange ASME B16.5 BW End ASME B16.25 Test API598 Special NACE MR-01-75 Features: Bolted Bonnet or Pressure Seal Bonnet Bypass on Request Full port or Conventional Port Swing Type Disc
Bonny Valve has very extended experience in manufacturing of Forged Globe Valves Size: inch up to 2 inch (DN 15 up to DN 50) Pressure Rating: ASME 150LB to 2500LB Materials: Forged Carbon Steel, Low Temperature Forged Carbon Steel, Forged Stainless Steel, Forged Duplex Stainless Steel, Forged Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Flanged RF, FF, RTJ, BW, NPT, SW Ends Operator: Hand wheel Operated Specification: Design API 602 / BS 5352 / ASME B16.34 End Flange ASME B16.5 BW End ASME B16.25 SW End ASME B16.11 Screwed Ends ASME B1.20.1 Test API598 Special NACE MR-01-75 Features: Bolted Bonnet, Welded Bonnet or Pressure Seal Bonnet Plug Type Disc/Conic Disc Full port or Conventional Port Outside Screw and Yoke (OS&Y), Rising Stem Extended Bonnet For Cryogenic Services
Bonny Valve has very extended experience in manufacturing of Cast Steel Globe Valves Size: 2 inch to 24 inch (DN 50 to DN 600) Pressure Rating: ASME 150LB, 300LB, 600LB, 900LB, 1500LB, 2500LB Materials: Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Flanged FF, RF, RTJ, BW Ends Operator : Hand wheel / Gear Operated Specification: Design BS1873 / ASME B16.34 Face to Face ASME B16.10 End to End ASME B16.10 End Flange ASME B16.5 BW End ASME B16.25 Test API598 Special NACE MR-01-75 Features: Bolted Bonnet or Pressure Seal Bonnet Plug Type Disc/Conic Disc Full port Outside Screw and Yoke (OS&Y), Rising Stem Extended Bonnet For Cryogenic Services Y Pattern/Angle Globe Valves/Bellow sealed Globe Valves
FORGED BOLTED / WELDED / PRESSURE SEAL BONNET Bonny Valve has very extended experience in manufacturing of Forged Gate Valves Size: �½ inch up to 2 inch (DN 15 up to DN 50) Pressure Rating: ASME 150LB to 2500LB Materials: Forged Carbon Steel, Low Temperature Forged Carbon Steel, Forged Stainless Steel, Forged Duplex Stainless Steel, Forged Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: NPT, SW, BW, Flanged RF, FF, RTJ, Ends Operator: Hand wheel Operated Specification: Design â??API 602 / BS 5352/ ASME B16.34 End Flange â?? ASME B16.5 BW End â?? ASME B16.25 SW End â?? ASME B16.11 Screwed Ends â?? ASME â?? ANME B1.20.1 Test â?? API598 Special â?? NACE MR-01-75 Features: Bolted Bonnet,Welded Bonnet or Pressure Seal Bonnet Solid Wedge Full port or Conventional Port Outside Screw and Yoke (OS&Y), Rising Stem Extended Bonnet For Cryogenic Services Locking Device Optional
CAST BOLTED / PRESSURE SEAL BONNET Bonny Valve has very extended experience in manufacturing of Cast Gate Valves Size: 2 up to 60(DN50 up to DN1500) Pressure Rating: ASME 150#,300#,600#,900#,1500#, 2500# Materials: Carbon Steel, Low Temperature Carbon Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, Nickel Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel Etc. End Connection: Flanged RF, FF, RTJ, BW Operator: Hand wheel, Gear OP. Specification: Design API 600 / ASME B16.34 Face to Face ASME B16.10 End to End ASME B16.10 End Flange ASME B16.5 BW End ASME B16.25 Test API598 Special NACE MR-01-75 Features: Bolted Bonnet or Pressure Seal Bonnet Flexible Wedge Full Port Outside Screw and Yoke (OS&Y), Rising Stem Extended Bonnet For Cryogenic Services Locking Device Optional By pass on Request
SPLINE PLUGE GAUGES Use: For Quick and Accurate inspection of internal involute/serration/ straight spline Range: Dia. 12mm to 150 mm Quality Standard: Involute Spline ANSI B92.1 1970 Material: OHNS SAE 01/02 Hardness: 58-60 Hrc. Profile: INVOLUTE/SERRATION/STRAIGHT Gauge Quality: As Per DIN-3962 Class-5
ultra small flow needle valve is a kind of top guide single seat valve, it has a simple structure, good sealing performance, reliable use and so on. The top guide system is effective enough to overcome the small opening shock, effective and long service life. A smaller flow coefficient is chosen to increase the use of the valve. Multi spring pneumatic film mechanism or electric actuator can be selected. The valve is the use of , professional development of a small flow of the operating conditions of a product. The body is small in size and light in weight, and the inner screw thread structure is more convenient to be installed and disassembled. The whole body has the characteristics of small size, light weight, high performance and precise control of micro flow.Does not apply to the medium of the more dirty occasions, adjusting the media containing granular media, should be aimed at the problem of small throttle clearance, pay attention to prevent the occurrence of blocking card phenomenon. Especially suitable for liquid, steam and other media in the mainstream of the regulation. required. Design featuresThe small opening range can be adjusted continuously The top guide structure, anti vibration The valve cone seal, the sealing effect is good Multi word design, good adjustment performance Valve seat spray welding hard alloy, corrosion resistance, long life Small size, light weight, easy to install The actuator mounted interchangeableTechnical parameterBody form Straight through type forging valve body Spool form Non balance type single seat valve Nominal diameter DN8 25 NPS 1/4" 1" Nominal pressure PN1.6 32.0MPa CALSS 150 1500 LB Applicable temperature 196 650 Optional Connection form Flange, Welding, Screw thread Flange distance Meet IEC 60534 Non-standard customization Gland form Bolt pressing type Sealing gasket Metal graphite gasket, PTFE Seal up PTFE, flexible graphite Actuatorï¼?Pneumatic actuator, electric actuator
Rotor types Y-shaped (120 angle) Height x Width x Depth/Passage Width (mm) 2208 1510 1330/650 Case brushed stainless steel The Raptor Y Max full-height turnstile solves the problem of restricting access for facilities with high perimeter security requirements. The Y-shaped modification leaves more room for passage, making it faster and more comfortable for the user, while maintaining absolute reliability of protection against unauthorized access, thanks to the locking system with smart-rotor position control function. The new mechanism was developed taking into account the high requirements for operational characteristics, including climatic conditions and reliability, therefore not requiring frequent maintenance, which gives the option to use the turnstile in places where it is difficult to set-up a permanent guard post. Raptor Y Max can be integrated with most access control systems available on the market, which means you can use it as part of an existing access control system, or choose the option that best suits your needs.
Model NO. DBW20 Pressure High Pressure Valve Structure Pilot Piston Structure Power Supply AC Solenoid Valve Usage Oil Standard DIN Application Application Warranty One year Feature Long Life Standard or Nonstandard Standard Fuel Diesel Performance Wearable Theory Axial Flow Pump Treatment Treatment Transport Package Wooden Package Specification casting Trademark Fucheng Hydraulic Origin China HS Code 8413910000 Production Capacity 10000 Pieces/Year
Any further inquiries please contact with me Valve Type CI / CS / SS WAFER CHECK VALVE Design Std API 598 / API 6D Size Range 25 DN to 600 DN [1 to 24] Body [SS - AISI 304 / 316] [CI- IS 210 Gr. FG 200 / ASTM A 126 Gr. B] [CS - ASTM A 216 Gr. WCB] Disc AISI 410 / 304 / 316 Seat NITRIL / EPDM / NEOPRENE / PTFE / SILICON Design Features Single Plate, Swing type, Self acting , Wafer type, Face Sealing - O ring, Horizontal / Vertical Mounting Pr.Rating [PN 10 / PN 16] [ASME - Class 150 / 300 / 600] Face to Face API 6D End Connection Sand witched Between Flanges: [BS 10 Table D / E ] [ DIN 2542 - PN 10 / DIN 2543 - PN 16] [ ASME B16.5, - CLASS 150 / 300 / 600 ] Testing Std. API 598 Optional Spring Loaded , Small / Large Groove faci
