Special adhesive film is made from the mixture of some petrochemicals. It makes full use of the permeability of this substance to penetrate into the micro-pores of the surface of the objects , and the characteristics of its cohesion to adhere tight to the objects . It is characterized by : (a)Can be attached tight onto the surface of the objects . (b)Can carry the weight . (c)Waterproof and can withstand high temperature -10¢J--80¢J . (d)Is very easy to be peeled off . (e)Environmental and economical , can be reused for a great number of times (but should be noted that the surface of the objects and films are both clean before pasting). In fact , the film can be used in a very wide range , such as : adhesive tape (single or double side), passes, stationery, childrens toys, printing posters, billboards.etc , and so on . Wherever in the kitchen , bathroom, bedroom , office , exhibition places and even in the freezer, film can be fully used . If we can make the most of our imagination and creativity, the film can practically make our daily life more convenient and comfortable . 21cmX31cm/piece.
Cf01 are series of decorative self adhesive films which are used three-dimensional textured vinyl that reflects light the same way as real carbon fiber parts to imitate the real carbon fiber effect. It is comprised of color textured vinyl with clear permanent adhesive and pe coating silicon release paper. Depend on your orderquantity, 150um*1.52m*50m/roll.
1. Advantage * Economical type, money saving, * Short term outdoor using. 1~1.5years * Soft film, good uneven holding ability Specification: Vinyl thickness Liner Width Length INK 80 micron 120g/m2 paper 0.914/ 1.06/1.27/1.37/1.52m 50m Solvent, eco, UV 2. Use area HK102 is intended for making graphics in the following area * Body of car, bus, truck, subway sign graphics * Flat wall body * Other flat substrates such as foam board, banner sheet 3. Limitation This type is not recommended for the following applications: * High substrates light block area * Dirty, solvent cleaned, grease, silicon coating which affect the adhesion of the glue. * Lacquered or painted surfaces freshly. The dried lacquered must be tested by user for compatibility 4. Temperature ranges Minimum application temperature > 9XC Service temperature range - 15XC to~ 70XC 5. Shelf life: 1 year in material's original packaging, storage temperature of 15-22 deg C. (80-100)um*(0.914,1.06,1.27,1.37,1.52)m*50m/roll.
Advantage * Suitable Solvent, ECO ink printing * 180g rigid high weight art paper, easy for lamination and field installation. * Soft vinyl (28Pa hardness) is suitable for arched glass surface. * Strong adhesion, anti-wind, anti UV. * Complete removable glue, no glue leaving behind the window after using Specification: Hole Ink diameter Open rate Film thickness with glue Liner Paper Width Solvent ECO UV 1.6mm 40% 150micron 180g art paper 1.27 / 1.37 /1.52m Yes Yes NO 2. Use area GK1001 film is intended for making graphics in the following area * Window of car or bus sign graphics * Building window for sign * Interior glass sign faces * Other transparent substrates such as transparent acrylic, polycarbonate 3. Limitation This type is not recommended for the following applications: * The surfaces of substrates are dirty, solvent cleaned, grease, silicon coating which affect the adhesion of the glue. Great K2 Industry Co., Ltd R & D Center - 2 - * The glass has built-in heating, defrosting elements or wipers * Restrict the safe operation of emergency window exits 4. Temperature ranges Minimum application temperature > 9XC Service temperature range - 25XC to + 75XC 5. Shelf life: 2 year in material's original packaging, storage temperature of 15-22 deg C, relative humidity of 50¡ã55%. 6. Durability: 1 year in outdoor solution. But it also depends on printing method and ink. Correct substrate preparation and maintenance of vinyl will enhance durability. 7. Technical data Composition High gloss vivid white/black vinyl Thickness with glue 150 Film micron Shrinkage after application ¡Õ1.1% Adhesive Type Clear Acrylic Solvent, pressure sensitive Removable ability Removable Adhesive Thickness 0.02¡Ó0.003 mm Adhesion 2.4 pounds/inch (Acrylic and uncoated, clear polycarbonate) 180 degree pull back testing. Type Rigid PE coating silicon art paper Weight 180g/m2 Release force 40g Liner SA rate >85% Salt water testing 100h/23XC no variation. 150um*(1.27,1.37,1.52)m*50m/roll.
Super clear and glossy BOPP film with single/both side (s) corona treated. It is widely used in packaging industry such as printing, lamination and Aluminum metallization. Featuring : Super high transparency and glossy, Super high tensile strength Super high grease barrier, Excellent ink and coating adhesion Low static electricity, Superior thickness uniformity Smoothness of the vertical section and much compact of film rolls winding Specifications Thickness: 12-75 micron Width:350-1600 mm Length: 4000m ,6000m ,7000m, 8000m Color: Transparent (clear). Packing: Use carton & pallets or as customers requirements.
BOPET film (biaxial oriented Polyester films) featurines good thermal stability and tenacity; low air and water permeability; applicable to vacuum aluminum plating, compound package, cooking bag manufacture, etc. Featuring : Having the good adhesion with ink and coating, can be used for multi-color printings with good flatness. Is mainly used in heat-sealing bags of frozen food, industrial products and cosmetics packaging. Specification: thickness: 12 microns-25 microns, 75 microns-150 microns ,185 microns-380 microns, 500 Microns width :200-1200MM length : 500m ,1000m ,1500m,4000m,6000m,9000m,12000m Polyester film is wound around paper shaft with an internal diameter of 76.2mm-152.4mm and covered with polyethylene film; each coil is supported by damper and put in carton; medium and large package needs wooden mount.
BOPP crystal adhesive packing tape jumbo-rolls ( Bopp Transparent & Brown Tapes acrylic water base size & solvent ) is widely used for slitting medium/smaller rolls for sealing heavy-duty cartons. 1) BOPP super clear adhesive packaging tape with water based acrylic adhesive, high-tensile strength and adhesion. 2) Colors: clear, tan, yellowish, red, dark brown, light tan ,white ,multicolor and printed so on . 3) Thickness: 35mic - 68mic 4) Width:980mm,1020mm,1280mm,1270mm,1635mm ,1640mm,others 5) Length: 4000 m ,4500m,6000 m 6) Qty: 1200rolls/day. Particular size and package style.
1.) Size : Thickness: 125,135,150 Mic Width:520mm,980mm,1020mm,1265mm,1270mm,1280mm,1300mm,1620mm ,1640mm,and others Length: 1500-1800m Color: white 2.) Features : Basic material : crepe paper Color: Beige Adhesive: rubber glue Total thickness:> 0.145 mm The adhesive :> 10 # 180 .c peel:> 5.5 N/25 mm Adhesion:> 6 H Temperature: room temperature, 60C, 80 C,10C .130 C .150 C.160 C .180 C .190 C .200 C .250 C Tensile strength:> 75 N/25 mm Elongation:> 9 3.) Main usage: High strength glue, good performance in paste resume, good stability. Applied to metal coating, circuit boards, copper positioning drilling, plastic positioning and spray, computer casings and electronic positioning spray painting and other purposes. Quantity: 1200rolls/day.
Thickness: 4.4, 4.5, 4.55, 4.6, 4.8, 5.0, 5.7, 6.0um Width: 500, 910, 980, 1010, 1200, 1500mm Length: 15000, 17000, 20000, 24000, 37000m Feature: clear/transparent Shrinkage and thickness stability Good heat resistance Easy processing in thermal transfer Application: suitable for use in bar code printers, fax machines and transfer ribbon.
Teflon tapes. 50 or 30 mtrs roll.
Two-sided Aluminum Foil single-layer Bubble Heat Insulation Material Characteristics: 1) Odourless, non-toxic and environmentally-friendly 2) Light and easy to install 3) Moisture-proof, waterproof and good sealing property 4) Light reflection, heat insulation, sound insulation, anti-radiation, shockproof, heat preservation and energy saving Usage: 1) Roof, wall and floor 2) Shell of air-condition, water heater, high temperature furnace 3) Protective coating of water pipe and ventilating pipe We combine aluminum foil which has the characteristic of heat and light reflection with bubble sheet made from LDPE. Applying to house construction area (roof, wall and floor), the product can keep over 80 percent of energy out of the building and protect the wall from the damage of great change of temperature. It can also greatly reduce the harm caused by ultraviolet ray penetrating iron, cob wall, wood wall and ordinary insulation materials, and provide functions of heat reflection, heat insulation, anti-radiation, heat preservation and energy saving.
Single-sided Aluminum foil EPE insulation material Characteristics: 1) Light, easy to be processed and installed 2) Waterproof, impermeable, heat insulation, shockproof, sound absorption and noise reduction 3) Heat-resisting, cold-resisting, chemical-resisting, aging-resisting 4) Insulate any heat media with a stable and low coefficient of heat conduction 5) Generate no pollutant bringing harm to people's health when being installed and in use. Usage: 1) Roof, wall and floor 2) Shell of air-condition, water heater, high temperature furnace 3) Protective coating of water pipe and ventilating pipe 4) Heat insulation, sound absorption and noise reduction for refrigerator car and laboratory 5) Packing for special products and cold storage 6) Material of isothermic bag.
Characteristics: 1) Light, easy to be processed and installed 2) Waterproof, impermeable, heat insulation, shockproof, sound absorption and noise reduction 3) Heat-resisting, cold-resisting, chemical-resisting, aging-resisting 4) Insulate any heat media with a stable and low coefficient of heat conduction 5) Generate no pollutant bringing harm to people's health when being installed and in use. Usage: 1) Roof, wall and floor 2) Shell of air-condition, water heater, high temperature furnace 3) Protective coating of water pipe and ventilating pipe 4) Heat insulation, sound absorption and noise reduction for refrigerator car and laboratory 5) Packing for special products and cold storage We combine aluminum foil with XPE. It is an environmentally friendly product with ability in heat preservation, insulation and barrier of moisture, fire and sound. Compared with EPE, XPE has stronger strength of extension and smaller bubble. It is an ideal material for heat preservation of automobile and air-condition. These years, XPE is widely used in market of sports relaxation, such as surfboard, moisture proof mat, shoe material and yoga mat. It also applies to architecture like insulation floor.
Characteristics: 1) Odourless and non-toxic 2) Clean, thin and light 3) Secure and environmentally friendly. Usage: 1) Insulation and heat preservation of roof, wall and pipe 2) Packing for household appliance, precise instrument, top grade porcelain and other artware 3) Packing for variety of products and cold storage. We combine aluminized foil with nonwoven cloth. It is an environmentally friendly product with ability in heat preservation and barrier of heat. The outer aluminum foil can reflect light and heat, while the inner woven cloth is soft and tear-resisting, which fills in gaps in ordinary insulation materials in domestic market. Its ability in heat preservation and heat insulation make it widely used, like interlayer material in luggage and ice bags.
Well established and cost effective way of collating bottles, cans, cardboard boxes and palletized goods. With growing demand in PE Shrink Film, as supplier of many global companies, SEPAS PLASTIK A.S. would be delighted to supply this product with any features upon your needs. The goods are palletized in different numbers depends on its dimensions.
The most outstanding characteristics of Polyimide film is for its high temperature endurance and insulation ability. To make a polyimide film, first form the film by condensing pyromellitic dianhydride(PMDA)and Diamino diphenyl ether(DDE) in strong solvents, and then be treated by imine at a high temperature It exhibit excellent thermal resistance, high insulation resistance, engineering properties, chemical stability, radiation resistance, inflammability and fire resistance rated at 94V-0. The product is halogen-free, and meets the environmental protection standard for its heavy metal and other restricted organic materials. Electronic parts, mechanic components, insulation on electrics, insulation tube, composite insulators.
Polyimide tube is made of polyimide material using special molding. Polyimide exhibits outstanding mechanical, electrical and thermal characteristics. Compared to other polymers, polyimide can be made into insulation tubes with extremely short diameter and thin wall thickness. The minimum inside diameter of 0.1mm is available and the thinnest wall thickness of 0.015mm is producible. This product ensures superior thermal resistance, high voltage resistance, chemical corrosion resistance along with other capabilities such as outgassing, anti-nuclear radiation, and optimal flexibility for easier installation. Polyimide tube can be used in insulation of wiring or circuitry which in need of thermal resistance, voltage resistance, and in products in need of protection from corrosion, radiation. Eg: a number of micro drives, heaters, small motors, circuit board testers, etc. According to customer's requirement.
Polyimide tube is made of polyimide material using special molding. Polyimide exhibits outstanding mechanical, electrical and thermal characteristics. Compared to other polymers, polyimide can be made into insulation tubes with extremely short diameter and thin wall thickness. The minimum inside diameter of 0.1mm is available and the thinnest wall thickness of 0.015mm is producible. This product ensures superior thermal resistance, high voltage resistance, chemical corrosion resistance along with other capabilities such as outgassing, anti-nuclear radiation, and optimal flexibility for easier installation. Polyimide Tube can be used in insulation of wiring or circuitry which in need of thermal resistance, voltage resistance, and in products in need of protection from corrosion, radiation. eg: a number of micro drives, heaters, small motors, circuit board testers, etc.. According to customer's requirement.
Polyimide Tape uses polyimide film as the backing material and is coated with silicone adhesive. It possesses excellent electrical insulation, dimensional stability, high temperature resistance, and leaves no defective gum when tearing off. This product can be used to masking Gold edge fingers and edge connectors during soldering and reflow soldering process within the PCB assembly industry. It is also used in electrical switches, motors, electronic transformers, relays, cables, coils, capacitors and electrical insulation applications meeting class H requirements in lithium battery.
The most outstanding characteristics of Polyimide film is for its high temperature endurance and insulation ability. To make a polyimide film, first form the film by condensing pyromellitic dianhydride(PMDA)and Diamino diphenyl ether(DDE) in strong solvents, and then be treated by imine at a high temperature It exhibit excellent thermal resistance, high insulation resistance, engineering properties, chemical stability, radiation resistance, inflammability and fire resistance rated at 94V-0. The product is halogen-free, and meets the environmental protection standard for its heavy metal and other restricted organic materials. According to customer's requirements.
