The air preheater exists the problem of collection of ash , worn down , low temperature corrosion to effect the safe and economical operation for the boiler unit . At the moment , the investment of air preheater is 6%-8% of the whole boiler investment in the industrial boiler and power station boil , due to the problem of collectionof ash, worn down, low temperature corrosion to incur the direct loss of replacing equipment and shuting down is 4~5% of the operation cost and the loss will be more large when the boiler is shut down incurred by this problem . Aim at the above questions,we develop the new heat transfer parts â??â??Enamel coated seam or seamless tubes with small enamel thickness ratio of thermal conductivity and received 5 patents . The uniform colour enameled tube is manufactured with the enamel which is our own developed with the scientific formula and is evenly coated on the surface of the steel tube by the auto enamel tube production line . To use best temperature change performance enameled tubes as the heat exchange parts will be anti-abrasion and anti-corrosion, the surface is smooth and low cost of maintenance .
Product Introduction The rotating-plate design (RAPH) consists of a central rotating-plate element installed within a casing that is divided into two (bi-sector type), three (tri-sector type) or four (quad-sector type) sectors containing seals around the element. The seals allow the element to rotate through all the sectors, but keep gas leakage between sectors to a minimum while providing separate gas air and flue gas paths through each sector. Tri-sector types are the most common in modern power generation facilities. In the tri-sector design, the largest sector (usually spanning about half the cross-section of the casing) is connected to the boiler hot gas outlet. The hot exhaust gas flows over the central element, transferring some of its heat to the element, and is then ducted away for further treatment in dust collectors and other equipment before being expelled from the flue gas stack. The second, smaller sector, is fed with ambient air by a fan, which passes over the heated element as it rotates into the sector, and is heated before being carried to the boiler furnace for combustion. The third sector is the smallest one and it heats air which is routed into the pulverizers and used to carry the coal-air mixture to coal boiler burners. Thus, the total air heated in the RAPH provides: heating air to remove the moisture from the pulverised coal dust, carrier air for transporting the pulverised coal to the boiler burners and the primary air for combustion. Our company and qualification Shandong HengTao Energy Saving and Environment Protection Co., Ltd. is a national comprehensive enterprise which is specialize in the R&D, manufacture, installation, energy saving & renovation of waste heat boiler, power station boiler and in forging, heating power support and automobile service. Our company has Grade A boiler manufacture qualification and Grade 2 pressure vessel manufacture qualification. Our main products are specialized in all kinds of boilers and boiler parts which included power station boiler, waste heat boiler, air preheater, membrane water wall and superheater. We are committed to creating the best solution provider for boiler integrated energy-saving technology transformation, and we will strive for it continually.
Brief Introduction Air preheater is the equipment that uses the boiler tail flue smoke to heat the entering air with its inside tubes .It is used to improve the heat exchange performance of the boiler, and reduce energy consumption. To adapt the different boiler burning type, different fuel and different fume ingredient, we developed the below enamel tube air preheaters to fit the different mediem: 1. The CFB boiler and coal powder boiler used enamel steel tubes, seam or seamless steel tube with green colour. 2. The rubbish burning furnace, biomass boiler used enamel steel tubes, seam or seamless steel tube with blue colour. 3. The Chain grate and layer burning boiler used enamel steel tubes, seam or seamless steel tube with brown colour. 4. The oil burning boiler, coking boiler and gas boiler used enamel steel tubes,seam or seamless steel tube with dark green. Why Choose Us? 1). Chinese famous brand 2). Competitive price with trusted quality 3). Short delivery lead time and excellent after-sale service 4). Certificate ISO9001, ISO14001, 5). We always produce good quality products with competitive price. 6). We have 50 professional engineers, 15 professional and technical teams for boiler improvement and more than 100 success cases of boiler energy-saving technological transformation.
We are leading manufacturers of electrical heating elements since 1968.We specialize in air heaters, water heaters, oil heaters, cartridge heaters etc.We make air heaters, water heaters, oil heaters, cartridge heaters, flange heaters, alkali immersion heaters, band mica/ceramic heaters, tubular heaters import substitutes, thermocouples, control panels, ovens, bobbin heaters, furnace elements, oil/water pre heaters, out flow heaters, infrared heaters, d section heaters, finned strip heaters, etc.
High temperature induced draft fan for industrial furnaces Product features : High temperature induced draft fan with direct connection with : 1. High efficiency: improving the overall fan efficiency 20 to 35%, reduce required 1to 2pcs motors 2. Motor direct connection, no bearing, no water cooling, no cooling fan. 3. Design temperature 250 degrees, maximum temperature of 350 degrees. 4. Stainless steel impeller and volute casing, high temperature and corrosion resistance 5. YE3 series of energy saving and high efficient motors 6. Volute and the base flange connection, convenient to replace the outlet angle. www.blenergy.cn
Hunan Baling Furnace Energy Conservation Co.,Ltd(Baling Energy, stock code:831054)is established in Nov.1998, as a professional high-tech manufacture engaged in R&D designing, manufacturing and servicing for industrial energy-saving furnace equipments. The main products include no bypass unpaired reversible regenerative combustion type furnaces, rotary regenerative air pre-heater, silicon carbide metal combination air pre-heater, blower and induced draft fan for combustion system etc., which are used widely for non-ferrous metal, machinery, building material, ceramic, steel, petrochemical and similar industries. www.blenergy.cn
Hunan Baling Furnace Energy Conservation Co.,Ltd(Baling Energy, stock code:831054)is established in Nov.1998, as a professional high-tech manufacture engaged in R&D designing, manufacturing and servicing for industrial energy-saving furnace equipments. The main products include no bypass unpaired reversible regenerative combustion type furnaces, rotary regenerative air pre-heater, silicon carbide metal combination air pre-heater, blower and induced draft fan for combustion system etc., which are used widely for non-ferrous metal, machinery, building material, ceramic, steel, petrochemical and similar industries. Baling Energy has owned the ISO9001 quality system, ISO14001 environment system, GB / T28001 Occupational Health and Safety System and CCC mandatory product certification; got 24 utility, inventions and appearances patents; 2 patents passed PCT international search; and the new patent of Reversible regenerative combustion system and Control system is in applying from 5 countries as America, Brazil, Mexico, India and Vietnam. The technology of No bypass unpaired reversible regenerative combustion and Silicon carbide metal composite air preheating received from the Hunan Science and Technology Achievement Appraisal office in 2013, with results of International advanced technology and leading domestic technology. The no bypass unpaired reversible regenerative combustion system can save more 15-25% energy than the traditional combustion system, meanwhile, this saving energy technology is certified by China Quality Certification Center in 2015 and listed in National key low carbon energy saving technology promotion directory(2015version energy part). Based on sincerity, mature quality, respecting clients and excellent service, Baling Energy is focusing on the furnace technology innovation, targeting smart and leading technology innovation. Through more than 10 years, Baling Energy has arrived and exceeded international advanced power consumption level. In the future, Baling Energy will keep developing the energy saving and low carbon technology, striving to become the leading professional supplier for complete industrial saving energy furnace equipments and control systems. Small air volume and high pressure blower Small air volume and high pressure blower Product features: 1. Small power, high pressure, small volume, low noise, high efficiency 2. Stainless steel blade, Impeller premarket 3. Impellers, blades, volute molding 4. Impeller static and dynamic balance correction, smooth running, small vibration 5. Volute and the base flange connection, convenient to replace the outlet angle.
BL Energy Industrial smelting furnace Application range : 1350degree regenerative series application Aluminum and other non ferrous metal smelting furnace Steel furnace, heat treatment furnace Temperature refractories, ceramics, sintering brick kiln 1650degrees regenerative series application Copper, steel, iron and other high temperature furnace Refractories, ceramics and other high-temperature sintering furnace Glass, building materials and other high temperature furnace Product Features Technical specification 1). Temperature efficiency: 90%,maximum as 93% 2). Total recovery rate of flue gas: 90%,maximum as 92% 3). Comparison with non energy saving furnace: 1350degrees Series energy saving rate : 40% to 60% 1650degrees Series energy saving rate : 50%to70% 4). Comparison with traditional paired regenerative combustion technology, the energy saving rate: 20%to30%
Regenerative materials selection The regenerative combustion system adopts the anti-erosion high purity corundum regenerative ball. Product features: 1. Good high temperature performance 2. Resistance of shock cold and shock heat 3. Bulk in density 4. High specific heat capacity 5. Good thermal conductivity 6. Good ash resistance 7. Good anti-erosion 8. Small pressure loss 9. Long working life span www.blenergy.cn
-1400°c, 1500°c or 1600°c maximum operating temperature -carbolite gero 301 controller, with single ramp to set-point & process timer -3, 8, 15 or 35 litre chamber volumes -soft closing parallel action door (3 & 8 litre models only) -silicon carbide heating elements provide long life and are able to withstand the stresses of intermittent operation -rhf 3 & 8 litre have a cast alumina hearth; rhf 15 & 35 have silicon carbide hearth -low thermal mass insulation for high energy efficiency
Electric furnace, heating chamber with electricity as the heat source for achieving very high temperatures to melt and alloy metals and refractories. The electricity has no electrochemical effect on the metal but simply heats it. Electric furnaces produce roughly two-fifths of the steel made in the united states. They are used by specialty steelmakers to produce almost all the stainless steels, electrical steels, tool steels, and special alloys required by the chemical, automotive, aircraft, machine-tool, transportation, and food-processing industries. Electric furnaces also are employed, exclusively, by mini-mills, small plants using scrap charges to produce reinforcing bars, merchant bars (e.G., angles and channels), and structural sections. The german-born british inventor sir william siemens first demonstrated the arc furnace in 1879 at the paris exposition by melting iron in crucibles. In this furnace, horizontally placed carbon electrodes produced an electric arc above the container of metal. The first commercial arc furnace in the united states was installed in 1906; it had a capacity of four tons and was equipped with two electrodes. Modern furnaces range in heat size from a few tons up to 400 tons, and the arcs strike directly into the metal bath from vertically positioned, graphite electrodes. Although the three-electrode, three-phase, alternating-current furnace is in general use, single-electrode, direct-current furnaces have been installed more recently.
Application: heating aluminum billet , shearing billet Features: auto billet loading , auto billet feeding , auto billet transferring , auto heating , auto length sized , auto sheat , auto billet moving , heat recovery. Advantage: non-oil leakage , low energy consumption , shear smoothly , precision shear length , hing configuration , long use life , high production , low fault . Parameters : Extruding machine : 450t~2000t Billet diameter : f70~f460mm Billet length: 2m~5m Shear length: 250mm~1500mm Shear tolerance: ±1mm Temperature difference: ±5?
This machine for growing crystals by Kyropoulos method. KY sapphire growing machine “Omega” Sapphire boule are high efficient yield sapphire single crystal materials. Yield rate of the Kyropoulos sapphire boule more high then other known methods. Main applied for LED-industry. Request Features: Closed water cooling system with proximity sensors control the flow and temperature of cooling water lines Software enables programs to form heating-cooling, each of which comprises a sequence of independent segments, defined by three parameters: the increment of the voltage on the segment length of a segment of time and limit the voltage on the segment. It is possible to maintain these programs in the electronic memory of industrial computer. The software implemented the ability to "hot" switch from one program to another. Control and monitoring provides a fully controlled by the user on the software and hardware levels of crystal growth process Implemented the ability to control mechanical parts installation, implemented the ability programming parameters of the heater power Furnace is equipped with preinstalled software on a perpetual commercial license "hot" switch between automatic and manual types of control, at any moment you can stop the execution of the current program is automatically carried out the process and manually setting the new parameter set to continue process in automatic mode Control and monitoring of the crystal growth is able to save all existing programmed parameters of the growth process in the nonvolatile memory. Software is the preservation of all operator actions and changes all the setup parameters in nonvolatile memory. Specification: Sapphire crystals weight 30 - 150 kg High automation of the process Special adaptive software Resistive heating Working atmosphere: vacuum Vacuum, torr: 2*10-6 Area required, sq. m : 10 Weight, kg: 2300 Power, kW: 40-100 Technological stages: loading crucible; pumping out working volume up to residual pressure 6x10-5 Tor; heating raw materials to 2100 Celsius and melting it seeding decreasing of the power with a given speed Sapphire crystal for: LED substrate Smartphones screens Camera of smartphones lens The specialized optical applications. Windows, lenses, prisms and etc Lens of a photo and a video cameras Screens protected schields Watch industry applications smart watches glasses such as «iWatch» Armored protective sapphire glass as windows for military equipment and special devices Sapphire plates as ballistic armor elements for vehicles Individual protection viewport Endoprosthesis Protective housings and domes
This machine for growing crystals by Czochralski method. CZ wide range crystal growing machine “Oxide”. Applied for lab and industry crystal making. Automatical diameter control system. High precision weight meter system with exclusive direct weight control design. Czochralski furnace “Oxide” crystal growth of different type materials: BGO, LSO, LiNbO3, YAG, PbWO4 and many other. Oxide crystals by using the Czochralski method, such as lithium niobate, lithium tantalate, alum-yttrium garnet (YAG), gallium-gadolinium garnet, etc (GGG). Request Features: Automatic growing ingot predetermined form (automatic diameter control) The system of direct weighing growing ingot (exclusive) Bottom rod with working and accelerate adjustable movement speed (supply for Customer request) Frequency heating (up to 20 kHz) with automatic frequency oscillatory circuit Furnace is equipped with preinstalled software on a perpetual commercial license Closed water cooling system with proximity sensors control the flow and temperature of cooling water lines Power stability of the heating system is not less than ± 0.01% Software enables programs to form heating cooling, each of which comprises a sequence of independent segments, defined by three parameters: the increment of the voltage on the segment length of a segment of time and limit the voltage on the segment. It is possible to maintain these programs in the electronic memory of industrial computer. The software implemented the ability to "hot" switch from one program to another. Many other features will added by Customer demand Specification: Inside height, mm: 400-1800 Inside diameter, mm: 400-800 Special adaptive software Heating type: inductive or resistive Run of the top rod, mm : 500-1200 Working atmosphere: vacuum, inert gas, hydrogen, oxygen Vacuum, torr: 2*10-6 Area required, sq. m : 6-12 Crystal weight, kg: 5-20 Power supply, kW: 20-120 Kind of materials: Alumo-Yttrium Garnet (YAG) Lithium tantalate (LiTaO3) Gadolinium Gallium Garnet (GGG, Gd3Ga5O12) Lead tungstate (PbWO4) Bismuth germanium oxide (BGO, Bi4Ge3O12) Langasite (LGS) Langatate (LGT) Gadolinium silicate (GSO) Germanium (Ge) Wide crystal range: Scintillator Laser Piezoelectric Different oxide crystals High temperature Special sensors Science materials Special optics Ceramics and glasses New high-tech materials
EFG furnace designed for growing shaped crystals (sapphire and other). Crystal growing machine by EFG method. "Orion" is sapphire crystal growing machine with max crystal weight 10 kg. The EFG machine can growing up to 38 tapes at one time. A crystal form depend from shaper. The furnace can be use for any profile products such as: tapes, tubes, profiles, rods, etc. Best effectivity solution for high quality sapphire glasses windows making. Lowest making cost for sapphire glass. Request Features: Automatic growing ingot predetermined form (automatic growing crystal speed control) The system of direct weighing growing ingot (exclusive) Bottom rod with working and accelerate adjustable movement speed (supply for Customer request) Resistive or Frequency heating (up to 20 kHz) with automatic frequency oscillatory circuit Furnace is equipped with preinstalled software on a perpetual commercial license Closed water cooling system with proximity sensors control the flow and temperature of cooling water lines Power stability of the heating system is not less than ± 0.01% Software enables programs to form heating cooling, each of which comprises a sequence of independent segments, defined by three parameters: the increment of the voltage on the segment length of a segment of time and limit the voltage on the segment. It is possible to maintain these programs in the electronic memory of industrial computer. The software implemented the ability to "hot" switch from one program to another. Many other features will added by Customer demand Specification: Automatic growing including seeding Presicion weight control system Inside height of chamber, mm : 1000-1,400 Inside diameter of chamber, mm : 450-800 Run of the top rod, mm : 450-1000 Heating type: inductive or resistive Working atmosphere: vacuum, inert gas Vacuum, torr: 7,5*10-3 Area required, sq. m : 6-12 Max Crystal weight, kg: 10 Power, kW : 30-90 Weight, kg : 2150 Applications: Smartphones screens cover Sapphire optics lens Smartphones camera lens Tube for high-temperature lamps Rods for medical Vehicle armor optics Science aparatus Sapphire crucibles Laser rods Screens protected schields Optical fiber Sapphire glass for smartwatches Individual protection viewport Capillaries
Lance tip is associating with the central iron and steel research institute, we can optimize the lance nozzle by your steelmaking practice. This would be suitable for your high-efficient oxygen blast demand and shorten the time of blowing, then you will get a better steelmaking efficient. The nozzle produced by the technology of vacuum casting has high-density organization with high copper purity, good thermal conductivity and long service life. With reliable welding technology of copper, and steel, the products, adapt to high temperature and high strength working conditions. The life of the nozzle used at the 250t bof of the second plant of baosteel increases by 30% than that the ordinary nozzle. The assembled nozzle made by forging has the properties of closely grain, high-density organization, high temperature resistance and strong resisting fatigue. By optimal designing the nozzle's inside passage of cooling water, the passage has smaller water resistance and good cooling effect.
We provide the clients with comprehensive and high-quality products by our exquisite and perfect technologies and offer specialized service support by highly efficient and rapid response capabilities, so as to spare no efforts in creating the utmost scientific and technological values for the clients. We sincerely hope that we can get ;;win-win;;¨¤ ending with insightful men from home and abroad hand in hand.
1200c muffle furnace is a ce certified high temperature furnace using high quality ceramic fiber board and resistance wire heating elements. The temperature of 1200c muffle furnace is controlled by high precision controller with accuracy +/-0.5 c and 51 segments programmable up to 1200c. This type of furnace is widely used for materials or chemical lab to sinter all types of new materials samples. It is an ideal box furnace for sintering high purity ceramic material at high temperature without element contamination. Muffle furnace features: 1) three sides resistance wire coil for fast and uniform heating serve as heating element 2) maximum energy efficiency is achieved by surrounding the chamber with thermal-efficient high purity alumina fiber ceramic insulation. 3) double layer steel case with air cooling to ensure low surface temperature 4) design of sliding down door is for loading materials easily 5) furnace chamber: 250x320x450mm 6) built in precision digital temperature controller is 51 segments programmable to control heating rate, cooling rate and dwell time. Temperature control unit can be separated from furnace, and make moving at easy. 7) the furnace temperature is controlled by precision scr (silicon controlled rectifier) digital controller with accuracy +/-1c and 51 segments programmable up to 1200c Muffle furnace applications 1. Gravimetric analysis 2. Sintering 3. Quantitative analysis 4. Heat treating 5. Glass preparation Chamber size 100x100x100mm(4"x4"x4") 150x150x150mm (6"x6"x6") 150x150x200mm (6"x6"x8") 200x200x200mm (8"x8"x8") 200x200x300mm (8"x8"x12") 250x250x300mm (10"x10"x12") 300x300x400mm (12"x12"x16") 350x350x400mm (14"x14"x16") 400x400x400mm (16"x16"x16") 500x500x500mm (20"x20"x20")
Vacuum gas atomization powder equipment is characterized by small environmental pollution, high degree of ball-shape powder, low oxygen content and fast cooling rate and so on.
Pyrolysis furnaces for charcoal production from various raw materials and packaging lines.Manufacturer & Exporter
