YGW Coal Thermal Fluid Boiler YGW Horizontal Coal Fired Thermal Fluid Boiler General Introduction This series thermal fluid boiler use heat transfer oil as medium. There is a hot oil circulating pump which in order to force the thermic fluid to flow in the closed loop circulation pipe. Then the thermal energy will be transfered to the heated object. The thermal fluid will back to the boiler furnace and be reheated. The YGW thermal fluid boiler can reach high temperature at low working pressure. It adopts advanced control system, equipped with liquid level controller, pressure controller, temperature controller, and alarms to make sure the boiler work orderly and safe. It is a safe boiler with high efficiency and low power consumption.
YYL Vertical Oil Gas Thermal Oil Heater YYL Vertical oil/gas fired thermal oil heaters use oil or gas as fuel, the heat transfer oils is heated in the boiler furnace first, then the thermal oil will flow in the closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon Oil/Gas fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Features of Oil/Gas Fired Thermal Oil Heaters 1. High Temperature This Oil/Gas fired thermal oil heaters can reach 320? at low pressure. 2. Easy Operation User friendly designed control system, easy to operate. 3. Low Investment Compared with steam boiler and hot water boiler, thermal oil boiler is perfect to give user high temperature in a much safer way. It cost little in maintenance and daily process. 4. PLC Intelligent Control System The PLC control system of thermal oil heaters is suitable for high temperature and high humidity environment of long-term operation.
Vertical Thermal Oil Boiler Thermal oil boiler is a indirect heating system, it is working under low pressure, so the performance is stable and safe. Thermal oil offers the user the capability of high temperature operation at very low pressures. Due to the low operating pressure and properties of thermal fluids, most heaters are operate easily and licensed boiler operator is not typically required. Working Princeple: Liquid phase heat transfer medium is heated in the boiler, and then flow and circulated to one or multiple heat energy users in a closed loop system. The thermal oil is flow by the force of a pump, there are 2 pumps in the whole system, one working pump and another one is a spare pump, in any case the working pump stoped, the spare pump will start work immediately, so the system wont breakdown. Bidragon offers standard thermal fluid heaters, custom engineered thermal fluid heaters, complete thermal fluid systems and a full range of parts and support for your process. Thermal Oil Boiler Applicable Industry Petrochemical Industries: polymerization, melted, condensation, distillation, removal H2. Oil industry: fat and acid distillation, grease decomposition, concentrated, esterification, vacuum deodorizer, high-temperature cooking, advanced salad oil. Synthetic fiber industry: polymerization, melt spinning, extending, drying. Textile printing and dyeing industry: heat setting, hot melt dyeing, melt bake calendering drying, high temperature stenter, oar yarn. Plastics and rubber industry: hot pressing, hot cast, vulcanization molding, calendering injection machine, plastic mixer, conveyor dryer, screw extruder. Paper Industry: dry, corrugated paper processing, egg tray, food cardboard drying, calendering machine, roller. Timber industry: multilayer plywood, fiberboard molding, plywood, wood drying, steaming equipment. Building materials industry: road bitumen heating, gypsum board drying, heating bitumen concrete, concrete elements curing, drying equipment. Air-conditioning industry: industrial plants, residential and hotel building heating. Detergent Industry: cooking boiler, autoclave, spray-washing tower, a conveyorized dryer, lipolysis device distillation column. The automotive industry: the tunnel-type drying room, degreasing baths, phosphate processing equipment. Electrical equipment industry: calendering machine, the platen machines, vacuum pan, dryer.
YGL Biomass Waste Wood Fired Thermal Oil Boiler Features of Biomass Series Waste Wood Fired Thermal Oil Boiler 1. Low Working Pressure This wood fired thermal fluid heaters can work under low pressure (1.1Mpa), and reach 300? at atmospheric pressure. 2. Accurate Control System Hot oil boiler, Oil-based thermal fluid are used as heater carrier in this heating system, it can achieve higher temperature. Operator can also control the temperature accurately to meet different industry requirement. 3. Safe and Reliable Performance There are dense coils installed at the top of the heater, this design can protect the boiler furnace top from burn out. 4. High Thermal Efficiency The theramic oil flow from the low inlet to the high out let, this design will discharge gas produced during the process, and it will improve the themal efficiency.
Horizontal Thermal Fluid Heated Steam Generator The WLE Series steam generator is heated by thermal fluid boiler, it is a high efficienty and cost saving system which can provide high temperature and steam at the same time. It is frequently required by factories that they need thermal oil heating system and the steam generator at the same time, and our WLE thermal oil heater can satisfy this requirement. Compared with seperate heating system and steam generator, WLE system reduce the investment cost and maintenance cost greatly. Working Principle When the high temperature thermal oil flows through the tube, the heat will turn the water into saturated steam, the steam will release and be used. Application of Thermal Fluid Heated Steam Generator Thermal Oil Steam Generator usually be used with thermal oil heater. Widely applied in food processing, rubber industrial, wood processing, oil production industrial, etc. It can meet the requirement of using one thermal oil heater to get hot thermal oil and steam at the same time which saving a lot of equipment investment and labor cost. It uses the continuous circulated thermal oil to generate steam which can replace the steam boiler.
Electric Heating Thermal Oil Heater Electric heated thermal oil heater is a perfect solutions for factories which are located in places where the electricity is cheaper than fuels. Electrical heated thermal oil boiler only required little maintenance so the running cost can be reduced a lot too. This type of thermal oil heater use the resistive heating working principle, thermic fluid is heated by electric heating elements. It is widely used in liquid and other process heating industry.
YWL Horizontal Coal Fired Thermal Oil Heater Horizontal type coal fired thermal oil heaters use coal as fuel, the heat transfer oils is heated in the tube first, then the fluid thermal oil will flow in the closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon biomass and wood fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Advantage of YLW Coal Fired Thermal Oil Heater 1. Double dense coils installed in the boiler furnace, the heating surface is more sufficient. 2. The theramic oil flow from the low inlet to the high out let, in this way, the produced gas can easily go out of the system. 3. Automatic temperature control system, operator can adjust the temperature precisely and accurately.
YLL Vertical Coal Fired Thermal Oil Boiler Coal fired vertical thermal oil boiler use coal as fuel, the heat transfer oils is heated in the boiler first, then the thermal oil flow in a closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon biomass and wood fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Advantage of YLL Vertical Coal Fired Thermal Oil Boiler 1.The oil flow from the lower place to the high place,in this process, the produced gas can easily go out of the system. 2.Automatic feed coal fuel, automatic discharge the slags. 3.Fire grate use independent air chamber, and the air space is larger, so the burning will be more sufficiently.
YGL Coal Fired Thermal Fluid Heater YGL Coal fired thermal fluid heater can reach high temperature (Max. 320?) at low working pressure. It has stable heating performance and precise humidity control system, It also adpots a complete operating control system and safety monitoring devices.
Vertical Thermal Oil Heated Steam Generator The WLE Series steam generator is heated by thermal oil boiler, it is a high efficienty and cost saving system which can provide high temperature and steam at the same time. It is frequently required by factories that they need thermal oil heating system and the steam generator at the same time, and our WLE thermal oil heater can satisfy this requirement. Compared with seperate heating system and steam generator, WLE system reduce the investment cost and maintenance cost greatly. Working Principle When the high temperature thermal oil flows through the tube, the heat will turn the water into saturated steam, the steam will release and be used. Application of Thermal Oil Steam Generator Thermal Oil Steam Generator usually be used with thermal oil heater. Widely applied in food processing, rubber industrial, wood processing, oil production industrial, etc. It can meet the requirement of using one thermal oil heater to get hot thermal oil and steam at the same time which saving a lot of equipment investment and labor cost. It uses the continuous circulated thermal oil to generate steam which can replace the steam boiler.
Steam Accumulator If the boiler can not produce enough steam in production, the accumulator will release steam and the inner pressure will be decreased, then the water will boiling and provide more steam to keep the whole system working under stable condition. Applicable Industry Steam accumulator is widely use in iron and steel industry, metallurgy industry, textile industry, chemical fiber industry, pulp and paper industry, brewing industry, pharmaceutical industry, food processing industry, power generation industry and other industries.
Offering the pricelist and quotation consultation, it is one of the best 1/13 hp - 1/4 hp hydroponic water chillers manufacturers and suppliers in China. Welcome to buy or wholesale 1/13 hp - 1/4 hp hydroponic water chillers from our factory. 1/13 HP - 1/4 HP Hydroponic Water Chillers With Hydroponic Supplies Hydroponic Chillers Performance : ?Chillers are suitable for use in reservoirs, hydroponic systems &fresh or saltwater aquariums. ?Each chiller provides a commercial-grade titanium heat exchanger for optimum performance and corrosion resistance. ?High quality Japanese compressor is extremely efficient and reliable. ?Digital LCD display for easy operation. ?Commercial grade chillers are available to the gardening industry . Why Do You Need a Water Chiller? Well technically, you don't. There are plenty of other ways to cool down your reservoir if you want to save some cash. However... High water temperatures are a consistent problem in many hydroponic setups, especially if you're using a small reservoir in a system like deep water culture. The rising temperatures decreases the amount of dissolved oxygen around the root zone. This in combination with the accelerated growth cycle of plants in a hydroponic environment usually results in oxygen deprivation. That means your plant dies. And dead plants are no good. Along with that, warmer water increases the like lihood that pathogens like pythium take root (pardon the pun) in your system. Chose LANDO Water Chillers for cooling is the best way . Chillers for Hydroponic Systems Product Specification :
Water Cooled UV Curing Systems Shenzhen Lando Company supply for Portable Laser Water Chillers cooled uv led curing systems and Uv Light Curing Equipment.Our Water Chillers Systems which cooling light curing systems ,also our industrial laser water chillers would be application for cooler CO2 tube . UV LED Curing Water Cooled Performance : ?Application : UV LED Curing Water Cooled , UV Printer Chillers or other industrials . ?One-stop automatic intelligent temperature control: in different environment, user does not need to change setting due to it will automatically ?switch to appropriate operating temperature. Voltage:110V-220V; Frequency: 50/60Hz; Refrigerant: R-22 / R-410a Industrial Water Chillers Cool CO2 Laser Tube Main Feature: * Compact thermolysis type industrial water chiller * Long working life and simple operation * Equipped with water flow alarm and over temperate alarm * Radiating capacity: 50W / °C * CE and ROHS certified * Power supply: 110 V or 220 V * Multiple alarm functions: Compressor time-delay protection, compressor over current protection, water flow alarm and over high / low temperature alarm www.lando-chillers.com Email : sales@cnlando.com
KLQ-DZ-type pneumatic furnace lining building machine feature: This machine is a kind of common machine ,size varies,mainly used for 0.5-60T if furnace bottom to knot. Packaging & Shipping Usually delivered by sea shipment container or trucks.
Usage:widely used for engineering machinery, auto parts, fasteners, bearings, chains, metal tools and precision parts industries quenching carburizing. Features: (1)electricity-saving:adopt high tensile calcium silicate board, ceramic fiber board, heat-resistant material for high Performance. (2)operation:adopt automatic control to save manual cost. (3)quality:equipped with a variable step string fan on the top of the furnace to get uniform temperature for high quality. (4) atmosphere:adopt methanol decomposition to stabilize gas and to ensure for quality. (5) stability: cp value tolerance±0.03%(carbon potential), and temperature equally dispersed at ±5?.
Vacuum Casting Furnace Introduction: As the most experienced Vacuum Casting Furnace manufacturer in China, ShinTek Vacuum Casting Furnace can be used for a wide of industries, can melting and pouring Ni-based alloy, special steel, precision alloy, NdFeB, Dysprosium metal, activated metal, super alloy, hydrogen storage material, magnetic material and so on… Vacuum Casting Furnace Specifications: Model STVIM-10 STVIM-25 STVIM-50 STVIM-100 STVIM-200 STVIM-500 STVIM-1000 STVIM-1500 Working zone size 5*3*2 4.8*4*2.5 9.8*5*3.2 9.8*5.5*5.0 11*8.7*4.6 12.5*8*6 16*12*7.6 17*14*8.5 Load (KG) 10 25 50 100 200 500 1000 1500 Power 40KW 50/100KW 100KW 160KW 200/250KW 500KW 500KW 1000KW Voltage 300V 175V 375V 375V 375V 700V 700V 700V Frequency 4000Hz 2500Hz 2500Hz 2500Hz 1600Hz 1000Hz 500Hz 500Hz Max. temperature 1600? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 6.7*10-3Pa Leakage rate =4Pa/h Remark: The Vacuum Casting Furnace can be customized for your specific project. Vacuum Casting Furnace features: (1) Vacuum Casting Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Casting Furnace – Suitable for most of metallurgy industries, can be customized for users; (3) Vacuum Casting Furnace – Two heating system are available for choose, either thyristor frequency converter or IGBT power system. (4) Vacuum Casting Furnace – Two feeding method for choose: Manual or Semi-continueous; (5) Vacuum Casting Furnace – Friendly control system.
Vacuum Furnace Introduction: ShinTek can produce varieties of Vacuum Furnaces, including Vacuum heat treatment Furnace, Vacuum Brazing Furnace, Vacuum Sintering Furnace, Vacuum Induction Melting Furnace and so on… Vacuum Heat Treatment Furnace: Vacuum Quenching Furnace, Vacuum Annealing Furnace, Vacuum Tempering Furnace, Vacuum Carburizing Furnace, etc... Vacuum Brazing Furnace: Vacuum Aluminum Brazing Furnace, Vacuum High Temperature Brazing Furnace, Vacuum Diffusion Brazing Furnace, etc... Vacuum Sintering Furnace: Vacuum Powder Metallurgy Sintering Furnace, Vacuum MIM Sintering Furnace, Vacuum Hot Pressing Furnace... The Vacuum Furnace can be used for a wide of industries, including High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy, Ti alloy, Beryllium Bronze, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal, magnetic material, nonferrous metal, etc… Vacuum Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.67 Pa/h Vacuum Furnace features: (1) Vacuum Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Furnace – Friendly control system.
Vacuum Annealing Furnace Introduction: ShinTek Vacuum Annealing Furnaces can be used for annealing varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Annealing Furnace Specifications: Model STVF-A-80 STVF-A-100 STVF-A-150 STVF-A-200 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 80KW 100KW 150KW 200KW Max. temperature 1100? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Annealing Furnace can be customized for your specific project. Vacuum Annealing Furnace features: (1) Vacuum Annealing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Annealing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Annealing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Annealing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Annealing Furnace – Friendly control system.
Vacuum Brazing Furnace Introduction: ShinTek can produce varieties of Vacuum Brazing Furnaces, including Vacuum Aluminum Brazing Furnace, Vacuum High Temperature Brazing Furnace, Vacuum Diffusion Brazing Furnace and so on… Our Vacuum Brazing Furnaces can be used in a wide of industries, including Stainless Steel, Copper alloy, high temperature alloy, Titanium alloy, Hard metal, ceramic metallization, silver-copper, aluminum, nickel alloy, electric radar board antenna, radiator, compensation, PTC heater, oil radiator, plate-fin heat exchanger and so on… Vacuum Brazing Furnace Specifications: Model STVF-AB-120 STVF-AB-200 STVF-AB-380 STVF-AB-580 Working zone size 1000*600*600 2100*900*900 3000*900*900 5800*1000*1200 Load (KG) 500 2000 3000 6000 Power 120KW 200KW 380KW 580KW Max. temperature 750? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.4 Pa/h Remark: The Vacuum Brazing Furnace can be customized for your specific project. Vacuum High Temperature Brazing Furnace: Model STVF-B-65 STVF-B-120 STVF-AB-150 STVF-AB-220 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 65KW 120KW 150KW 220KW Max. temperature 1320? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.5 Pa/h Remark: The Vacuum Brazing Furnace can be customized for your specific project. Vacuum Brazing Furnace features: (1) Vacuum Brazing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Brazing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Brazing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Brazing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Brazing Furnace – Friendly control system.
