S-w boiler has been engaged in manufacturing thermal oil heaters from our establishment in 1993. To make energy-saving and environment-friendly thermal oil heaters is our focus. Now we have a products category which can cover this special boiler industry. Through constant international cooperation about technique and experience, our manufactures have a leading quality and superior specifications. To optimize your energy solution is our eternal pursuit. S-w heaters have been used in a variety of applications throughout many industries. Food, plastic and chemical processing as well as pharmaceutical and bio-fuel production are only a few of the many existing applications using s-w.
Horizontal Thermal Fluid Heated Steam Generator The WLE Series steam generator is heated by thermal fluid boiler, it is a high efficienty and cost saving system which can provide high temperature and steam at the same time. It is frequently required by factories that they need thermal oil heating system and the steam generator at the same time, and our WLE thermal oil heater can satisfy this requirement. Compared with seperate heating system and steam generator, WLE system reduce the investment cost and maintenance cost greatly. Working Principle When the high temperature thermal oil flows through the tube, the heat will turn the water into saturated steam, the steam will release and be used. Application of Thermal Fluid Heated Steam Generator Thermal Oil Steam Generator usually be used with thermal oil heater. Widely applied in food processing, rubber industrial, wood processing, oil production industrial, etc. It can meet the requirement of using one thermal oil heater to get hot thermal oil and steam at the same time which saving a lot of equipment investment and labor cost. It uses the continuous circulated thermal oil to generate steam which can replace the steam boiler.
YLM thermal fluid heater is square coil horizontal chain grate shop-assembled heater, chain grate and heater proper are transferred separately. It adapts chain grate to realize mechanical feeding coal, mechanical venting by blower and induced draft fan, and mechanical discharging by slag machine. Fuel falls on the grate from coal bucket during operating and burning, high temperature smoke enters furnace by passing combustion arch, after radiation heat exchange, smoke enters convection heating surface for convection heat exchange, then goes to waste heat boiler and air heater, at last enters dust collector then is vented into the atmosphere through chimney by induced draft fan.
YGL Coal Fired Thermal Fluid Heater YGL Coal fired thermal fluid heater can reach high temperature (Max. 320?) at low working pressure. It has stable heating performance and precise humidity control system, It also adpots a complete operating control system and safety monitoring devices.
YWL Horizontal Coal Fired Thermal Oil Heater Horizontal type coal fired thermal oil heaters use coal as fuel, the heat transfer oils is heated in the tube first, then the fluid thermal oil will flow in the closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon biomass and wood fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Advantage of YLW Coal Fired Thermal Oil Heater 1. Double dense coils installed in the boiler furnace, the heating surface is more sufficient. 2. The theramic oil flow from the low inlet to the high out let, in this way, the produced gas can easily go out of the system. 3. Automatic temperature control system, operator can adjust the temperature precisely and accurately.
With our years of experience & in-depth knowledge in this field, we are engaged in offering a quality-assured array of Electric Thermic Fluid Heater. Details: A Thermic Fluid Heater (Thermal Oil Heater) is industrial heating equipment, used where only heat transfers are desired instead of pressure. In this equipment, thermic fluid is circulated in the entire system for heat transfers to the desired processes. Combustion process heats up the thermic fluid and this fluid carries and rejects heat to the desired fluid for concluding the processes. After rejecting it, this fluid comes back again to the thermic fluid heater and this cycle goes on. Arizon Thermal Systems offers Thermic Fluid Heater / Thermal Oil Heaters fired by extensive range of fuels. Thermic Fluid Heater / Thermal Oil Heaters are available in both solid fuel firing as well as LDO /GAS / DUAl fuel firing variants so that you get the advantage of economically available fuels. Four Pass Solid (Coal / Wood) Fuel Fired Thermic Fluid Heater: The Four Pass solid fuel (coal / wood) fired Thermic Fluid Heater comprises of two heat exchangers namely radiant pass heat exchanger & convective pass heat exchanger. Radiant pass heat exchanger is a coil with conical shape & highly graded insulating material on outer surface to resist heat loss. Convective pass is made of two parallel concentric helical coils designed for sufficient convective heat transfer. This set of coils is covered with shell & this shell is insulated to resist heat loss. Radiant and convective heat exchangers are connected by a specially designed refractory duct which allows flue gas to pass from radiant to convective zone. Complete unit consist of radiant coil, convective pass, Fire chamber with sufficient grate area, F.D. fan for forced combustion, Air pre-heater to retrieve tremendous amount of heat from flue gas and transfer it to combustion air, Multi-cyclone separator to separate ash particles from flue gas & I.D. fan to induce air from the system & pass it to chimney for exhaust. Features: Efficient Heat Transfer with optimum combustion Three Pass Design for LDO / GAS fired Three Pass as well as Four pass Design for solid fuel fired Reduced excess air with balanced Draft System 300°C at near atmospheric pressure Truly maintenance Free Easy access for inspection & cleaning Energy Efficient Fully automatic in operation, so no running attention required Application: Asphalt & Road construction Dyes, Chemicals and Intermediates Textiles & Process house Packing Petrochemicals & refineries Rubber product industries Wood / ply wood industry Pharmaceutical & drugs Food processing Ceramics Reactor vessel heating, Jacketed vessel heating, autoclave & tank heating
Thermic Fluid Heater
Thermic fluid heater coils
4-PASS Thermic Fluid Heater
