APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Tiles Adhesive (CT-01),(02),(03), Tiles Epoxy Grout, Tiles Grout (Light Color), Tile Grout (Dark Color), Tiles Epoxy Grout Sparkle, Block Jointing Mortar, Wall Putty, Floor Hardener Non-Metallic, Tile Spacer (2mm, 3mm, 4mm,5mm), SBR. Etc. Products are available in stock.
Supplying business of construction chemicals like Water proofing coating material for plaster and concrete
Hardner Hardner : specially formulated for precast industries (paver blocks & precast cement articles).Fxt hardner is a colourless viscous water soluble liquid to be added in concrete mix for casting precast articles. Special features: Water white: it is colour less hence does not hinder the colours used in manufacturing of precast articles & white cement. Packing: 5, 50 & 250 kgs in hmhdep drums Packing: 5, 50 & 250 kgs in hmhdep drums
Coverage: 3.5 to 5 m²/kg depends on concrete Specific gravity at 30°c :- 1.75 Application temperature :- 5 °c to 45°c Drying time :- approx 2 hrs at 30°c 250ltr
Termisolve B PRO is unique and effective anti termite chemical. Many anti termite chemicals contain poisons. Termisolve B-PRO contains solvents and inorganic boric salts along with traditional herbal extracts which are known as anti termite since a long time. In a nutshell it is a combination of modern chemistry and proven knowledge of our ancestors. Salient features: Termisolve B PRO is applied as a treatment to the surroundings of existing buildings to prevent and correct termite problems. Termisolve B PRO is ideal for pre and post constructed buildings Anti termite treatment of structures Anti termite treatment for timber structures and wood. Termisolve B PRO is ideal barrier between termites and the building. Termisolve B PRO can be used by following ways. Treatment at the foundation level. Treatment to top surface at plinth level. Treatment of soil at wall and floor junction. 10,20,50,05,200 Liters packing.
Cement clinker
Whiteness = approx 85 to 90% Setting time = 20 to 30 minute Water ratio = 1:1.5 Laminated innerlining hdpe new poly begs under 40kg packing
All type of construction chemicals\ home decor\industrial paints Different shipment
Size = 3*2 feet Weight= 8kg Width= 11 mm Whiteness = approx 75% Handle with care, easily broken item . Minimum order 1000 sheet along with 17 mt plaster of paris powder
Description : K Crete SPR 14 is a high range water reducing agent and retarding plasticizer for concrete. K CRETE SPR 14 is supplied as brown liquid based on modified sulphonated Nepthalene slump retainer Plasticiser. The powerful dispersing agent of the high range water reducing super plasticizer can be used in many ways to obtain dense, high strength durable concrete (M35, M40, M45 M50). The high water reduction properties makes of K CRETE SPR 14 an ideal application in precast concrete where high early strength is of paramount importance. K CRETE SPR 14 is chloride free. Increases workability : K Crete SPR 14 when incorporated in concrete mixes increases the workability without the risk of segregation and bleeding. K CRETE SPR 14 also retains the slump for much longer time which facilitates easy placement. Increases strength : K Crete SPR 14 can be used to reduce water content transportation and for a given workability which leads to increased early and ultimate (28 days) strength. Such a high early strength facilitates early removal of formworks. 1, 5, 10, 50, 100, 200 kg carboys
Clinker - raw material for cement. In bulk packing
Perlite ore 15 kg-20 kg-50 kg
Activated bleaching earth Very effective for rice bran, soya oil
Bondacoat Ar Bondacoat Ep Bondacoat Pva Bondacoat Sbr Epogrout Hs Rendragrout Hf (Adhesive & Grouts) Tile Adhesive Ep Tile Grout Ep Epomortar Fc Eposcreed 10 Fillgrout Ep10 Fillgrout Pu40 Rendacoat Fc Rendagrout Hf (Concrete Repairs) Concoat Ep100 Concoat Ep150 Concoat Ep250 Concoat Resin Concoat Sl Elastoguard Pu Prime Ep100 Tg Prime Ep100 Prime Eps Prime Eps40 Proofseal Pu Concoat Eps Concoat Ept500 Deguard Sheild Sn- Wr636 Deguard Sheild Sn Waterbased- Wr637 Concoat Slc90 Elastocryl 700 Elastocryl 800 Elastocryl 900 Epocoat Epwp Epoflex 500 Proofseal Pt Epocoat Epwp Epoflex 500 Proofseal Pt Proofseal Pu Epogrout Hs
HI-PCE WR 50 is a high performance polycarboxylate ether , specifically developed a high range water reducing agent mainly used as a raw material to produce different types of high performance water reducing polycarboxylate based superplasticisers.
Dubond's Micro Concrete is supplied as a ready to use dry powder which requires only addition of clean water at site to produce a free flowing non shrink repair micro concrete. This is a cementious material, with additives, which impart controlled expansions characteristics in the plastic state while minimizing water demand. This is specially designed for repairs to damaged reinforced concrete elements, particularly where areas is restricted and where vibration of the placed material is difficult or impossible.
There are many industries in the leading refractory market who is constructing a lot of alumina mortars in India but Imperial World Trade continues leading of others due to its high quality and regular production of its products. We manufacture 70 K mortar using special quality of raw material stuff in our tremendous plant where state of the art of technology is functioned.
COCONUT SHELL The strongest part covering the coconut fruit is the coconut shell.They are used to produce handcrafts and biodegrable products. Due to their strength they are used effectively in the handmade decorative items and also have long time life period. USES >Ice cream cups >TO produce active carbon >Utensil >Plywood >Coconut shell powder SPECIFICATION Moisture 15% Dust 3%
