Find Verified Electronics Communications Suppliers, Manufacturers and Wholesalers

Electronic timer

Electronic multitester

Our dol starter comes with inbuilt single phase preventor & auto start unit.The multi tester detects the presence of ac voltage by remote sensing without actually touching the live wire

It is available in various capacity i.E. 200 amp, 300 amp, 400 amp, 500 amp, 600 amp, 700 amp, 800 amp. Also it can be customize for bulk need. Clip are available in various models

10 - 13 depanding of size of kit

Socket

Sockets are made up of high quality steel with proper heat treatment and industrial finish grade wich improves the life of sockets.
Impact socket, extension sockets, heavy duty socket, special socket, nut runner, stud driver, adaptor, quick change adaptor, bit socket etc.

Antenna trainer

Experiments that can be performed
01. Polar plots & polarization.
02. Wave modulation & demodulation.
03. Antenna gain.
04. Antenna beam width.
05. Element current Study.
06. Front-back ratio study.
07. Antenna matching.
08. Antenna radiation with distance.
09. Antenna Fabrication Study.
10. SWR Measurement.
SPECIFICATION & FEATURES
1.0. Antenna Trainer consists of the following built-in parts:
1.1 RF Generator - 750 MHz Approx. (Output Adjustable)
with Level Display on DPM.
1.2 Modulation Signal -1KHz approx. Sine wave
(Output Adjustable).
1.3 Slot Line Matching Stub - Slider Type.
1.4 Directional coupler - Forward and Reverse
( Selectable ).
1.5 Antenna Rotation - 0-360 Deg.Resolution 1 dig.
1.6 RF Output Connector - 75 ohm.
1.7 Main ON/OFF Switch and Jewel light for power Indication
and Power Cord.
1.8 Power supply -230V AC 10ª% 50Hz.
2.0. RF Detector with Level Adjustable Analog Meter with
Mounting Stand.
3.0. Antenna Fabrication Kit Including to PCB's and
+ Kg.14 S.W.G. wire roll.
4.0 Good Quality, reliable terminal/sockets are provided at
appropriate places on panel for connections / observation
of waveforms.
5.0 Strongly supported by detailed Operating Instructions,
giving details of Object, Theory, Design procedures,
Report Suggestions and Book References.
ANTENNAS ACCESSORIES
Transmitting Antennas Type AT -1001- ........
01. Simple Dipole l / 2
02. Simple Dipole l / 4
03. Simple Dipole Antenna 3/2l
04. Folded Dipole
05. Yagi UDA Folded Dipole (3 E)
06. Yagi UDA Simple Dipole (5 E)
07. Yagi UDA Simple (7 E)
ANTENNA TRAINER
OMEGA TYPE AT - 1001
08. Yagi UDA Folded Dipole (5 E)
09. Hertz Antenna (Horigental end Fed)
10. Ground Plane Antenna
11. Slot Antenna l / 2
12. Loop Antenna
13. Rhombus Antenna
14. Helix Antenna
15. Phase Array l/2 Antenna
16. Phase Array l/4 Antenna
17. Broad Side Array
18. Combined Collinear Array
19. Log Periodic Antenna
20. Simple Dipole Cut Paraboloid Antenna
21. Zeppline Antenna (Horigental end Fed)
OTHER ACCESSORIES
01. Current Probe comprising of two PCBs
Connected by Shielded Cable.
02. Transmitter Mast
03. Detector Antenna:(Folded dipole with reflector)
04. BNC-Tee
05. BNC-BNC adapter M
06. BNC-BNC adapter F
07. BNC-BNC cable-18"
08. Operating Manual & workbook
09. Accessories case
10. Patch Cord
11. Polar Graphs( 25 Nos.)
12. Polar Graphs (For Normalised Reading)(25 Nos.)
13. Allen key
14. Aligner Taparia 911( Duly filed )
15. Text Book "Antennas"

110 kgs

Digital Timer offered by FABROTECH are useful for time and control application in various industries. The 4/6 digit Timer can be used in different combination of Hour, Min. & second covering the time range from 0.1 second to 999999 Hour with the help of dip switches.
It can be RESET by front switch or from rear terminal. The UP/DOWN counting or cyclic mode can be selected through dip switch. Cyclic mode can have equal ON & OFF time OR unequal OFF+ON time set by 2+2 (4digit) & 3+3 (6digit) thumbwheel switches.
0.56 inch height bright red LED¦s display the time. The output is provided through 1 or 2NO/NC relay contacts rated at 5A/230V. Output can be delayed ON or delayed OFF. Relay can be latched or AUTO RESET (the relay activation time of 1sec. to 99sec. can be provided by factory for AUTO RESET).
Optionally, non volatile memory is provided to store the time.
The power consumption is less than 5 Watts. Operating supply voltage is 230 V AC + 10%, 50Hz. Housed in enclosure of DIN size 96(H) x 96(W) x 110(D)mm.
Also available miniature timer in 48 x 48, 4/3/2 thumbwheel without display or dial type timer.


EACH, 600GMS, 96X48

Inductive proximity sensor
Input voltage 8~32 vdc, sensing distance 2~10 mm
Size m-12 and m-18, m-28 , rectengular or as per
Specifications diamentions user oriented

12 pcs, 120 pcs

Solid state relay
Input Ac 3~32,Ac220,Dc 3~32v
Output Ac 200~270 v
Load 10 A, 16A, 25A, 40A

12 pcs,120 pcs

Wire wound resistor
Resistor ranging from 1 watt to 10000 watt
0.1ohm to 100k

Thermistor protection relay
Used for giving fool proof protection against overheating alongwith PTC thermistor
Uses the signal of ptc thermistors and switches off the equipment to be protected when dangerous temperature is attained
Available with large variety of input supply voltages for the convinience of the user
The relay is din rail mounting type

Weight is approximately 200 gms
Dimensions (h x w x d):
77 x 30 x 115 mm

Circular threaded coupling connector
The shells are made of aluminium alloy and the insulator is neoprene rubber, contacts are made of copper alloy and are silver plated
The shells are cadmium plated with olive drab chromate finish
The current rating is upto 150 amps depending upon shell size and contact arrangement. Insulation resistance is 5000 mega ohms minimum

Material can be packed according to the ordered size in standard packs.