Circular Threaded Coupling Connector

we are leading manufacturer & exporter of standoff/spacers as per requirement or Drawing

1.it is the waterproof connector

2.Accoring to the standard DZ4Q/RE008-84

3.Shell size:FQ14,FQ18,FQ24,FQ30

4.Contact:each shell size have diffrent pins

Working temperature: -55 degrees Centigrade- +100 degrees Centigrade
Relative temperature: Temperature is 40 degrees Centigrade, reach 93í+ 3%
Vibration: Frequency 10-200HZ, acceleration 150m/s2
Collide : Acceleration 490m/s2
Permanent acceleration vibration: The acceleration reaches 245mm/s2

Atmospheric pressure: Reach 4.4KPa

Mechanical life-span: 500 times

The connector should be able to stand the test of 30 minutes but not enter water within the connector in water 1 meter deep

1.LEMO connector, mini connector
2.copy of the lemo connector, but the technist can meet the requirement
3.shell size:0,1,2

The circular electronic connector are designed for the connection between sensors and electronic instruments or equipments .The connector is compact and its push-pull elf-laching connecting system allows the connector to be mated simply

VIBRATION CONNECTORS MANUFACTURERS & SUPPLIERS
Stainless steel vibration eliminator:
Aeroflex Vibration eliminators are specially designed to absorb mechanical vibration and destructive force of noise which is transmitted by the compressor, and also eliminate the stresses linked with piping thermal expansion in refrigeration and air condition installation.

These connectors are TIG welded stainless steel hose with copper pipe, due to there is not any brazing so these connector bear more temperature as compared to brazed fitting

The main function of vibration eliminator is to absorb compressor vibration and stop its transition into pipe network, by isolating the vibration the risk of damage to pipe work and related component reduce,
1.1 Size range of vibration eliminator:
The comprehensive range of vibration eliminator are available from to 3 1/8 Outer diameter of copper tube, copper tube are comply a per ASTM B88 & ASTM B88M (water & general plumbing system) & ASTM B280 (air conditioners & refrigeration system)

1.2 Material specification:
Aeroflex Vibration eliminators are manufacture from EN 10028-7, Stainless steel SS 321 & SS 316L annular corrugated hose with SS 304 stainless steel braid.

All unit are brazed with copper tube, detail dimension of pipe and vibration connector are in the table.

All the units are ultrasonically cleaned and completely dried made suitable to refrigeration system

Individual package of connector are remain under sealed plastic tubing.

The maximum test pressure is 1.5 time of maximum operating pressure and minimum burst pressure is 5 time of maximum operating pressure.

Copper tube end are designed as sweat connection for refrigeration tubing which have inner surface as per ASME B16.18

1.3 Installation conditions:
Aeroflex vibration eliminator should be installed as close as possible to the compressor and end away from the source of vibration.

Vibration eliminator should be installed perpendicular to the direction of vibration (in-line with the compressor crank shaft)

Horizontal Vibration: Where source of vibration is only in the horizontal plane, a single vibration and noise eliminator may be installed. Best results will be achieved by installation at 90�° to the source which is normally the crank of the compressor in a horizontal plane. See fig. 1
Vertical / horizontal vibration: Where the source of vibration and noise is in both horizontal are in vertical planes. Best result will be achieved by installing two vibration eliminators at right angle to each other see fig. 2
Although the copper tube end of vibration absorber are attached by TIG welding (special alloy filler) during installing if unit is over heated there is not effect on the connector

Photo link

Features
íñ high speed signal transmission
( 13.2mbps, nrz signal )
íñ input ttl compatible
íñ +3~+5v power source

Descriptions
The light transmitting unit is a standard-package product with connector and opto-electric component packaged with led and drive ic. The function of unit changes the electric signal into light signal and be transmitted by plastic fiber.
The unit is operated at single+3v~ +5v and the input signal is ttl compatible. It has a maximum operating speed of 13.2 mbps. The light signal is coupled into plastic fiber by connector. The unit has high performance at low dissipation current, steady light output and efficient light coupling.


Applications

íñ audio equipment
íñ dvd player
íñ pc, notebook
íñ sound card
íñ set top box



2000 pcs

Electrical character
Rating voltage: 60v ac/dc ,
Insulation resistance: >20m
Rating current : 4a
Contact resistance 5m

Other specification
Contact pin: 4pin brass with gold plating.
Insulation plastic:pa+gf or pur or lcp
Coupling nut/screw: brass with nickel plating
Degree of protection: ip67/ ip68
Operating temperature: -25c ~ +90c
Equivalent for binder's m12 connector
It can be usd in electromechnical&mechnism, egineering etc.


According to customer demand

Features of optical mini jack

íñ High speed signal transmission
(13.2Mbps, NRZ signal )
íñ Input TTL compatible
íñ +3~+5V power source
íñ Automatically detects the presence of a mini-plug in the jack and distinguishes an optical mini-plug from an electrical mini-plug

Descriptions
The light transmitting unit is a standard-package product with connector and opto-electric component packaged with LED and drive IC. The function of unit changes the electric signal into light signal and be transmitted by plastic fiber.
The unit is operated at single+3V~ +5V and the input signal is TTL compatible. The DLT13M1 has a maximum operating speed of 13.2 Mbps. The light signal is coupled into plastic fiber by connector. The unit has high performance at low dissipation current, steady light output and efficient light coupling.

Applications

íñ MD player
íñ Portable player


Tray 100 100 pcs 13.5*27*3 cm
Inner box 20 tray/box 2000 pcs 29*29*22 cm
Outer box 2 inner box/outer box 4000 pcs 60*31*25.8 cm