rail cow bar for track work It is for situations such as these that the jim-crow comes into its own. The jim crow was slotted over the rail about four or five sleepers away from the offending joint.and the screw tightened until it engaged with the edge of the rail. Then tightened the screw a further half-turn - thus bending the rail slightly.This process was repeated, moving the jim crow one sleeper nearer the joint each time and each time adding one more half-turn. This introduces a gradually increasing curve to the rail as it nears the joint.If you compare these two pictures with those showing the kinks above, you can see the difference.
rail shoe buffer Friction buffer stops for mainline person and goods traffic railways are especially designed to withstand an impact with large masses with max. speeds of 25 km/h. The track systems and the used locomotives or cars in addition to their buffer geometry determine the type and design of the corresponding solution. Friction buffer stops that are also able to withstand the permanent stress in shunting operations are what characterise. A buffer stop or bumper is a device to prevent railway vehicles from going past the end of a physical section of track. The design of the buffer stop is dependent in part upon the kind of couplings that the railway uses, since the coupling gear is the first part of the vehicle that the buffer stop touches. The purpose of a friction buffer block is to secure the track end and its direct surroundings as well as the rail vehicles themselves. If the brakes fail, the buffer stop should be designed to decelerate the vehicle safely and in controlled manner until it stops.
NQG5III Rail Cutting Machine NQG5III Internal combustion rail cutting machine is suitable for cutting rails of 43kg/m 75kg/m . The quality of cutting section meets the requirement of railway industrial standards. Its a necessary tool used in railway overhaul, maintenance and rush repairing operation. It has features of fast cutting speed, high utilization rate of thin grinding wheel, high quality of cutting section, easy operation, easy movement, safe use and wide application range etc.
Treadmill,elliptical,exercise bike,spinning bike,benches,racks,cable motion,fitness equipment accessories.
Rail Carrying Roller Roller manufactured in special steel and used for moving long-welded rails. The supporting structure is composed of a roller that runs on two bearings and it is able to support the weight of the rail.
Gantry Crane Rail Changer This equipment is suitable for the old and new switching operation of rail, switch rail and frog point rail. There are running wheels in the center of both sides, which can be carried out during transportation. It has the characteristics of adjustable height, lateral adjustment, locking, light weight, convenient handling and wide application range. The equipment can be equipped with section rail transport trolley, rail transport, switch rail and frog point rail operation trolley. The wheels are nylon wheels with good insulation performance and equipped with brake device. It is safe and reliable with light weight and high operation efficiency. It is an ideal special tool for rail transport in construction operation of Railway Public Works Department. Details Images
Hydraulic rail leveler Hydraulic rail levelers are suitable for vertical straightening at the joints of various types of rails on railway lines to make the joints of two rails straight. This machine has the characteristics of simple structure, convenient operation and reliable quality. It is suitable for maintenance, overhaul and emergency repair operations in the public works department.
Hydraulic rail bending machine rail bender Hydraulic rail bending machine also called hydraulic bend machine, is rail installation maintenance when a special tool to bend the rail operations.Hydraulic bend machine is a dedicated to laying railway line in tunnel mining slope level elevation changes at the scene of the track-laying for below 50 kg/m or light rail vertical bending or adjustment. Hydraulic rail bending machine designed by the principle of hydraulic transmission and leverage, using static pressure on curved track rail horizontal and vertical curve or straight rail operations.
SNGM-180 Angle Grinder SNGM-180 portable internal combustion rail grinding machine for all types of rails for all-round grinding, its small size, flexible and lightweight, simple operation, high grinding efficiency, easy to carry, easy maintenance and repair, but also for other Occasions.
Rail wave grinding machine The GBM-7.6 rail wave abrasion grinding machine is a professional machine used for the wave abrasion and grinding of the rail top. This machine is suitable for various rails of 43~75kg/m.
Rail wave grinding machine The GBM-7.6 rail wave abrasion grinding machine is a professional machine used for the wave abrasion and grinding of the rail top. This machine is suitable for various rails of 43~75kg/m.
Hydraulic rail bending machine This hydraulic rail bending machine is used for the bending operation of railway seam lines and welded joints of seamless tracks and other low-collapsed parts of steel rails. It can also be used as vertical bending and supporting equipment in the laying of seamless tracks; suitable for all types Rails. The machine has simple structure, convenient operation, safe operation and easy maintenance. It is an effective tool for rectifying rail joint problems
Rail Clamp The Rail Clamp is an innovative temporary rail joint clamp used prior to welding and to safeguard rail defects prior to repair. The Rail Clamp has been engineered to eliminate many of the disadvantages of other traditional rail clamp designs and provides enhanced performance under all conditions of use. The Rail Clamp design is radically different to the legacy design and guarantees a positive pre-torque angle so as the bolt is tightened the bolt holes remain aligned, eliminating the risk of bent bolts. We test have proved that bolts remain straight even at twice the recommended torque. Allows suction jars to be attached to stand rail One rail clamp holds one canister Rail can hold up to four rail clamps and canisters
Rail Clamp The Rail Clamp is an innovative temporary rail joint clamp used prior to welding and to safeguard rail defects prior to repair. Specification Model:LJ-JJQT Type:Rail Clamp Material:Stainless Steel Weight:6.5kg
Switch Rail Clamp Scope of use of portable hook lock: 1. Lock switch when repairing switch signal switch machine. 2. Lock the switch when passing the special train. 3. When temporary power failure occurs, the train runs and locks the switch. 4. Closed special line lock special line turnout. 5. Line new switch lock new open switch open. 6. Lock the switch during the construction of the special line.
Digital Track Gauge Digital Track Gauge can directly read the measurement values of railway track gauge, super elevation , check rail gauge and back to back distance through microelectronics, embedded and sensor technologies and OLED display screen. FEATURES AT A GLANCE 1. Large LED backlit display: especially suitable for day outside and dark night 2. Quick calibration operation: simple measurement process 3. Large capacity battery:long standby time 4. Accurate measurement:keep long-term stability 5. Temperature compensation :working temperature is -30~+55â?? 6. Insulated design 7. Anti-electromagnetic interference 8. Waterproof:could use in rainy day 9. power saving function: no operation within 15 minutes, the system will automatically shut down. 10. Approval by CHINA ACADEMY OF RAILWAY SCIENCES
YD-22 hydraulic Tamping Machine is a kind of professional machinery used for railway line ballast tamping maintenance except for turnouts. It can be operated with train interval time, without closing sections. It is equipped with three power modes. They are petrol, diesel and electric. BENIFITS Engine types: Honda GX390 petrol engine or SF 190 diesel engine or electric engine. It is suitable for the tamping operation in the new construction of ordinary railway lines and the large-scale or medium-scale railway line maintenance It can complete the tamping operation of various types of concrete sleepers and wooden sleepers Equipped with automatic rail clamping device Equipped with the f-tac walking frame, the machine can be removed off at any place and any time
Internal Combustion Rail Rust Remover Internal combustion rail rust removal machine is suitable for rust removal on the surface of various types of rails, and grinding wheels can be installed to achieve rail to grinding operatipons, quality meets the requirements of railway industry standards, and is the line overhaul and maintenance of railway public works departments. and ideal tools for emergency repair operations. This machine has the characteristics of reasonable design, compact structure, easy operation, flexible upper and lower roads, easy to move, wide range of application, and one machine for multiple purposes.
Electric Rail Grinding Machine The design of FMG-2.2 electric rail profile grinder allows you accurate and stable profile grinding up to 90�°about the rail head by rotation of the machine using its turming device and its inclinable operating arm. According to customer needs, 380V three-phase motor can be selected as power or 220V single-phase power as power. With good visibility of the grinding area assures you of a high quality finish.
CNC Rail profile grinding machine This rail profile grinding machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency.
