We promise that we are doing our best to meet your demands.
Original, Like a New/Excellent Working Condition, all Tested. it's separated from New equipment. Surface Condition(Dimpes/Embossing) : Excellent (Never used : It is the same as the Original New Condition ).
Near infrared heater 380x140x110, 2kg, wall-type, stand type
We have an extensive stock of surplus parts and 2nd source parts, largely for AMAT, Centura, Endura, HDP Ultima Plus, Novellus, LAM, Mattson, TEL Parts, IMP Parts, etc. This stock changes regularly as we gain excess items from our many equipment refurbishment projects
Ceramic heater are widely used in pre-heating of plastic sheets for vacuum forming & thermoforming, drying paints, lacquer & varnish curing, drying printing inks, drying textiles, activating adhesives, removing surface water from objects or moisture removal from fabric and paper, animal husbandry and rearing.The ceramic IR heaters are highly efficient.Ceramic infrared heater offers precise targeting and control with minimal peripheral heat. It is possible to apply heat only where and when it is required.
Only defects that cannot be refurbished are defects on the puck, like cracks and fractures of ceramic parts. There are heat wires inside the ceramic puck and if the puck is broken,it is very probable that heat wires are damaged, which cannot be repaired.
In case of all Mca e-chuck, Mca heater, ESC, ALN Heater, Magnet Assy products used in PVD manufacturing process, we offer a various services of refurbishment that are conducted by our own engineers and in-house. Or if customers ask, we provide new one.
The Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility not recommended for car washes. This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so it's great for use during power outages. Requires Millivolt thermostat for SGM sold separately. May require the following second stage regulators prior to the heater based on gas supply pressure
MCA ESC is a key consumable part of the PVD equipment used in the deposition process in the semiconductor manufacturing process that should be replaced regularly due to high temperature/ high pressure conditions and quality problems because of impurities in the chamber.
AMAT MCA E-chuck Heater PVD process parts warranty : 3 months condition : Used like OEM-New (All refurbished) P/N 0010-01288 AMAT MCA E-chuck Heater PVD process parts
Heating furnace. - able to heat object marerials in verious temperatures - maintain the optimum combustion status and Reduces the amount of generated scale. - excellent insulation property and a small thermal storage amount - desinged to be operated conveniently and efficiently. - designed to recover waste heat from exhaust gas for the reductiuon of energy consumpton.
Heat treatment furncace. -able to produce best-quality products by maintaining temperature distribution in the furnace evenly. -designed to maintain temparature difference within ¢®¨ú5¢®¨¡c during the entire heating process - furnace equipped with a high-performance furnace suitable for marerials and uses. -designed to be operated conveniently and efficiently with focus on energy saving and quality improvement.
Reheating furnace -designed to obtain a high temperature-increasing speed and even quality, and be operated conveniently and efficiently with focus on energy saving and quality improvement.
Hop-dip galvanizing facilities. - technologies accumulated for over 20 years. - supplied largest hot-dip galvinizing facilities in korea. - achived quality improvemenet and productivity by using special winch system. - achived durability of galvanizing pots through an automatic temperature control system and a flat burner using gas as a heat source.
Mesh Belt Type Furnace is designed to load the product on the mesh belt and make continuous production. It is used in various processes, including plastic working, firing, drying and degreasing, for a variety of production. Using the muffle, Mesh Belt Furnace offers stable ambient control, rapid heat-up time and radiating energy saving. It is designed to implement continuity of automated production system and uniform production based on ambient per zone and temperature control.
Pusher Furnace, a representative equipment in the firing process, is designed to push the conveyor using the pusher to move the product. It is used for the firing process of various types of products and it shows excellent heat resistance, insulation efficiency and wear resistance against the conveyor. Designed as a tunnel type, Pusher Furnace implements continuity of automated production system and uniform production based on ambient per zone and temperature control.
Batch Type Furnace can be comprised of several types, such as rack, roller or elevator, and pre-process product input and post-process product output is made in 1 cycle. Batch Furnace is used for plastic working, firing, drying and degreasing of various products. Unlike the continuous furnace, it can be installed in an independent location, with advantages of convenient layout and excellent price competitiveness.
Roller Hearth Kiln is a furnace that loads the product on the roller and make continuous production. It is used in various processes, including plastic working, firing, drying and degreasing, for a variety of production. It is designed to implement continuity of automated production system and show excellence in speed variation by roller running per zone and rapid heat-up capability.
Silicon Carbide Resistance Heater Single Screw 1550 Silicon Carbide Heating RodSpecifications 1. High working temperature: 1500C. 2. Long time last. 3. Varous type available. Rod, U, W, Single Spiral, Double Spiral Silicon Carbide Heating Rod Advantage . 1. High working temperature: 1500C (Surface Temperature) 2. Various shapes: Rod, U, W, Single Spiral, Doule Spiral shapes are availible. 3. Large size range: Diameter 14-54mm, Length 200-4500mm. 4. Fast Delivery: Normal quantity can be ready in 10 days. 5. Very competitive prices. How to Order Silicon Carbide Heating Rod 1. Choose the shape you need, like Rod, U, W, Single Spiral etc. 2. Out Diameter (OD) 3. Heating Zone Lengh (HZ) 4. Overall Length (OL) 5. Resistance you need. Order Sample: Rod type, OD30mm, HZ300mm, OL800mm, Resistance 0.4ohms. Silicon Carbide Resistance Heater Single Screw 1550 â?? 0 Silicon Carbide Resistance Heater Single Screw 1550 â?? 1 Normally the following should be given when describing any type of SiC heating elements: Type: ED, U, W, SC, SCR, DB,G, H, or DM Outside Diameter (OD) : mm Length of Hot Zone (HZ) :mm Length of Cold Zone (CZ) :mm Length of Overall(OL):mm Center Distance (A) :mm Resistance (at 1050â??+/-50â??) :�© Physical property of SIC heating element specific gravity 2.6~2.8g/cm bend strength >300kg hardness >9MOHS tensile strength >150kg/cm³ porosity rate
