We can produce all types of drilling rods such as HDD drilling rods, oil drilling rods, geological drilling rods, anchoring drilling rods and other special drilling rods, and trenchless special drilling tools such as pilot guide bits, swivels, ream bits, reducer unions,pneumatic pipe-rammer,hydraulic power break out tong for drill pipe.
We supply slick drill collars, spiral drill collars and non-magnetic drill collars; their sizes are from 3-1/8 to 11 inches. Besides the drill collars in the table below, we can supply other drill collars at customers' request. Materials: Drill collars are manufactured from AISI 4145H modified steel, and are supplied in the "as rolled" surface finish condition. Alternative surface finishes are available. Trepanning and Heat Treatment: Drill collars are trepanned and drifted to API Spec 7-1. Full-length heat-treatment processes ensure that mechanical properties meet or exceed API Spec 7-1 requirements. A hardness range of 285-341, Brinell hardness and Charpy "V" notch minimum impact strength of 40 ft-lb at 70 F are guaranteed one inch below the surface. Traceability: Drill collar material and process traceability are maintained from receipt of the mill's certified raw material to completion of manufacturing. Serial numbers are die stamped on bar bodies. Rigid Inspection Procedures: We inspect all our drill collars to ensure compliance with API SPEC 7-1 standards. These inspections include visual dimensional checks as well as ultrasonic inspections over the entire body of the drill collar. Cold Rolling: Drill collar thread roots, as well as elevator recess upper radius, are cold-rolled. Cold rolling creates a compressive recess upper radius stress condition that increases fatigue life by minimizing crack initiation. Phosphate-coated or Copper Plating: All connections are phosphate-coated or copper plated to improve resistance to corrosion. Slip Groove, Elevator Groove and Size: Lake offers optional slip and elevator recesses to improve handling efficiency and safety. Unless otherwise specified, slip and elevator recesses are machined in compliance with API spec 7-1 guidelines. Thread Protectors: Our company offers steel, cast steel and plastic steel thread protectors for its drill stem products.
We supply slick drill collars, spiral drill collars and non-magnetic drill collars; their sizes are from 3-1/8 to 11 inches. Besides the drill collars in the table below, we can supply other drill collars at customers' request. Materials: Drill collars are manufactured from AISI 4145H modified steel, and are supplied in the "as rolled" surface finish condition. Alternative surface finishes are available. Trepanning and Heat Treatment: Drill collars are trepanned and drifted to API Spec 7-1. Full-length heat-treatment processes ensure that mechanical properties meet or exceed API Spec 7-1 requirements. A hardness range of 285-341, Brinell hardness and Charpy "V" notch minimum impact strength of 40 ft-lb at 70 F are guaranteed one inch below the surface. Traceability: Drill collar material and process traceability are maintained from receipt of the mill's certified raw material to completion of manufacturing. Serial numbers are die stamped on bar bodies. Rigid Inspection Procedures: We inspect all our drill collars to ensure compliance with API SPEC 7-1 standards. These inspections include visual dimensional checks as well as ultrasonic inspections over the entire body of the drill collar. Cold Rolling: Drill collar thread roots, as well as elevator recess upper radius, are cold-rolled. Cold rolling creates a compressive recess upper radius stress condition that increases fatigue life by minimizing crack initiation. Phosphate-coated or Copper Plating: All connections are phosphate-coated or copper plated to improve resistance to corrosion. Slip Groove, Elevator Groove and Size: Lake offers optional slip and elevator recesses to improve handling efficiency and safety. Unless otherwise specified, slip and elevator recesses are machined in compliance with API spec 7-1 guidelines. Thread Protectors: Our company offers steel, cast steel and plastic steel thread protectors for its drill stem products.
Application: High chrome bimetal liner is used as a kind of mud pump fluid end accessories in the oil drilling industry. Features: Our bimetal liner, API certified, providing wear-resistant outer sleeve and high chrome corrosion-resistant inner sleeve. The high chrome liner has high rigidity of HRC>65 after heat treatment. Advantages: The bimetal liner offers long service life of about 800 hours, which is 2 to 3 times the lifetime of common ones in serve environment. Lake Petro has very rich experience in supplying spare parts of mud pump to the worldwide Oil Drilling industry.We stock and sell a wide selection of mud pump fluid end expendables and spares parts. Mud pump parts for F series mud pump, For P series mud pump, For PZ series mud pump, For 3NB series mud pump. These parts include liners, pistons, valves & seats,piston rods, rod clamps, extension rods, all fluid end seals and gaskets, fluid cylinder modules and accessories, as well as power end components, such as crankshaft assemblies, gear sets, connecting rods, crosshead, and bearings.
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
1.Cutting structure this type TCI tricone bits: The durability of premium tungsten carbide insert is improved with new formulas and new techniques for insert bit. 2.Gauge structure this type TCI tricone bits: Multiple gauge protection with gauge trimmers on the heel of cone, tungsten carbide inserts and hardfacing on the shirttail increases gauge holding capability and bearing life. 3.Bearing structure of this type TCI tricone bits: High precision bearing with two thrust faces. Ball lock the cone. Hardfaced head bearing surface. Cone bearing inlaid with friction-reducing alloy and then silver-plated. Abrasion resistance and seizure resistance of the bearing are improved. 4.Seal and Lubrication of this type TCI tricone bits: Premium Oring, optimal seal compression and curved seal structure can enhance the seal performance. The pressure compensator system and advanced grease can greatly increase the lubricating reliability . 5.Product Application this type TCI tricone bits: It can receive high WOB in the conventional drilling. It is suitable for various formations by matching cutting structure with different tooth shape, tooth density and tooth exposure height. 6.Advantage: 1. High-strength, high flexibility, high temperature and high wear resistance. 2. High-precision metal seal. 3. Locking roller ball, to adapt to high-speed. 4. The use of high strength high toughness carbide teeth, 5. Hours in the rotary cone bit with the impact, crushing and shearing the role of broken rock. 6. Cone bit to adapt to the soft, medium and hard of various strata. 7. Reasonable price and long working life.
SizeWeightPlain end weightDiameterGradeWall thickness Lb/ftkg/minmmInmm 2 3/86.656.269.322.37560.3E,X,G,S0.287.11 2 7/810.49.7214.482.87573E,X,G,S0.3629.19 3 1/29.58.8113.123.588.9E0.2546.45 3 1/213.312.3118.343.588.9E,X,G,S0.3689.35 3 1/215.514.6321.793.588.9E0.44911.4 3 1/215.514.6321.793.588.9X,G,S0.44911.4 41412.9319.264101.6E,X,G,S0.338.38 4 1/213.7512.2418.234.5114.3E0.2716.88 4 1/216.614.9822.314.5114.3E,X,G,S0.3378.56 4 1/22018.6927.844.5114.3E,X,G,S0.4310.92 516.2514.8722.155127X,G,S0.2967.52 519.517.9326.715127E0.3629.19 519.517.9326.715127X,G,S0.3629.19 525.624.0335.795127E0.512.7 525.624.0335.795127X,G,S0.512.7 5 1/221.919.8129.515.5139.7E,X,G,S0.3619.17 5 1/224.722.5433.575.5139.7E,X,G,S0.41510.54 6 5/825.222.1933.056.625168.3E,X,G,S0.338.38 6 5/827.724.2136.066.625168.3E,X,G,S0.3629.19
We can produce all types of drilling rods such as HDD drilling rods, oil drilling rods, geological drilling rods, anchoring drilling rods and other special drilling rods, and trenchless special drilling tools such as pilot guide bits, swivels, ream bits, reducer unions,pneumatic pipe-rammer,hydraulic power break out tong for drill pipe.
We supply slick drill collars, spiral drill collars and non-magnetic drill collars; their sizes are from 3-1/8 to 11 inches. Besides the drill collars in the table below, we can supply other drill collars at customers' request. Materials: Drill collars are manufactured from AISI 4145H modified steel, and are supplied in the "as rolled" surface finish condition. Alternative surface finishes are available. Trepanning and Heat Treatment: Drill collars are trepanned and drifted to API Spec 7-1. Full-length heat-treatment processes ensure that mechanical properties meet or exceed API Spec 7-1 requirements. A hardness range of 285-341, Brinell hardness and Charpy "V" notch minimum impact strength of 40 ft-lb at 70 F are guaranteed one inch below the surface. Traceability: Drill collar material and process traceability are maintained from receipt of the mill's certified raw material to completion of manufacturing. Serial numbers are die stamped on bar bodies. Rigid Inspection Procedures: We inspect all our drill collars to ensure compliance with API SPEC 7-1 standards. These inspections include visual dimensional checks as well as ultrasonic inspections over the entire body of the drill collar. Cold Rolling: Drill collar thread roots, as well as elevator recess upper radius, are cold-rolled. Cold rolling creates a compressive recess upper radius stress condition that increases fatigue life by minimizing crack initiation. Phosphate-coated or Copper Plating: All connections are phosphate-coated or copper plated to improve resistance to corrosion. Slip Groove, Elevator Groove and Size: Lake offers optional slip and elevator recesses to improve handling efficiency and safety. Unless otherwise specified, slip and elevator recesses are machined in compliance with API spec 7-1 guidelines. Thread Protectors: Our company offers steel, cast steel and plastic steel thread protectors for its drill stem products.
1. Bit Breakers The Bit Breakers are suitable to make up or break out the drilling bit during the oil well drilling and repairing operations. The Users should be chosen the bit breaker according to the size and model of the drilling bit. Feature:Improve support and retention Advantage:Manage the magnitude cutter loading and bit torque Benefit:Improved bit durability and directional responsiveness Advantage:Higher nozzle counts and/or fixed ports to best serve cleaning,cooling and cuttings evacuation requirements with available hydraulic flows.Allow for higher flow rates with minimal increase in pump pressure. 2. Detailed introduction to Bit breaker 1>Bit breaker is mainly used to screw on or off a rock bit to the bottom of drill string. 2>It can also prevent the rock bit from dropping into well hole. 3>The price of it is cheap and the use of it is safety and reliable. 4>It is easy to operate. First, the bit breaker is placed on well hole and then put the rock bit onto it. Turn it to screw on or off the bit by turnplate.
API high quality mud pump bi-metal liner, triplex mud pump liner 1.Mud Pump Liner Type: Bi-metal liner, ceramic liner 2.Mud Pump Liner Standard: API 7K Mud Pump Liner Description: 1. Our company could supply all spec premium liners and ceramic liners used in various brands of mud pumps. 2. Our premium liners are made of a forged steel outer shell and a high chromium iron inner sleeve. The out shell is centrifugally forged with high quality carbon steel, with Tensile Strength > 610Mpa, Yield Strength > 450 Mpa, Elongation >17%, Hardness HB -180-200; The inner sleeve is centrifugally forged with high chrome iron alloy, with Hardness over HRC62 after heat treatment. Each liner is machined to close tolerances to assure ease of installation and long liner life with the inside diameter of these premium liners honed to a mirror-like finish for smooth even wear during the life of the liner. It could serve more than 800 hours. 3. Our ceramic liners are made of a forged steel outer shell and a ceramic inner sleeve. We can supply Zirconia(ZrO3) sleeves as well as Alumina(Al2O3) sleeves. The ceramic liners are mainly used for well drilling and geological explorations especially widely used in harsh oil mining environment, offshore well&gas exploration etc. It serves a 5 to 10 times longer life than metal products, and will cut down the mining cost of more than 50%.
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
Our company manufactures Wireline Drill Rods, BQ, NQ, HQ, PQ, PHD, Parallel Threaded Drill Rods, DCDMA Sizes AW, BW, NW, HW, and Metric sizes 42 mm, 50 mm, 60 mm to 90mm. Note: 1. Thread oil should be used when screwing the drill rod and hammer knocking should be prohibited. 2. The drill rod stand should have buffer materials, like wood, rubber, and more. The contact between the threaded ends and iron tools should be forbidden. 3. During the relocation of drill rod, the thread protector should be screwed on the threaded parts so as to protect it from damages.
From WLA to WLP, Parallel Threaded Drill Rods, DCDMA sizes AW-HW, and Metric sizes 42mm to 90mm, tapered threaded drill rods, DCDMA sizes AWY to NWY, AWJ, BWJ and S75 drill rods. Specification: 1. Our drill rods are of the highest quality ,are manufactured to exacting specifications using advancing maching technoogy. 2. They are manufactured from seamless steel tube by cold drawn.The material is XJY850/30CrMnSiA which meets the global standard. 3. Drill rods are made from quality heat treated materials which ensure superior strength, wear resistance and toughness in the most demanding applications. 4. Rods and casing are manufactured under stringent industry standards, and are field tested under a variety of conditions. 5. All rods are designed to be compatible with other rods manufactured to the standard DCDMA.
The mud pump piston assembly is one of the main parts of the hydraulic end system of the mud pump.The discharge pressure of the mud pump is generated by reciprocating linear motion of the piston assembly in the piston.Piston assembly by the piston core, rubber, spring, pressure plate, etc. Our mud pump pistons are strictly manufactured according to API Standard, which with a high performance in various well drilling environment. The hub is forged from high quality steel, and the piston rubber is made from specially formulated compounds which are of heat, oil and water resistance. It is interchangeable with all other API standard designed pistons. And the valve rubber is easy to install.
DTH Drill Rods (Tubes/Pipes) and Sub Adaptors: Acedrills has DTH drill rods with several different thickness designs for each diameter, made from different grade steels for selection. So, in practice of field drilling, under different condition, there may be in need of different kinds of drill rods for particular application. For example, the thicker ones with general high quality grade steel for drilling hole of average depth, such as blasting holes; and the thinner ones with better grade steel for drilling hole of very deep, such as drilling for ground thermal. Moreover, Acedrills DTH drill rods are also well heat-treated, precision manufactured, and friction-welded.
DTH Drill Rods (Tubes/Pipes) and Sub Adaptors: Acedrills has DTH drill rods with several different thickness designs for each diameter, made from different grade steels for selection. So, in practice of field drilling, under different condition, there may be in need of different kinds of drill rods for particular application. For example, the thicker ones with general high quality grade steel for drilling hole of average depth, such as blasting holes; and the thinner ones with better grade steel for drilling hole of very deep, such as drilling for ground thermal. Moreover, Acedrills DTH drill rods are also well heat-treated, precision manufactured, and friction-welded.
product name: 24 inch steel body PDC bit diameter: 24 inch blade quantity: 6 nozzle quantity: 9 connection thread: 75/8" AP Reg pin usage: water, oil, gas well drilling application formation: hard rock formation Company profile Hebei Crossing Drill Bit Manufacture CO.,LTD is a professional supplier of drilling tools,including tricone bit,PDC tricone bit,Hole opener,single cone bit and so on.With years of study and refining of the introduced technology, we have succeeded in the field of product research with proprietary intellectual property rights.Also, we have made major breakthrough in the lines of analogue simulation in bottom-hole flow field,profile optimization,design of inserts arrangement and low torque,material and manufacturing techniques etc. As a result, our products own better characters of service and ranges of application.Mainly used for oil and gas,mining,geothermal,construction and so on. The products of our company have achieved industrialization and serialization.Besides our company has always laying importance on the technical exchanges and cooperation with the counterparts both at home and abroad.Our products have been sold all over the world, including the United States, England,Canada,Brazil,Russia,Italy,Iran,Saudi Arabia,Korea, India, and Poland and so on. The main products we can provide: 1.tricone bit(steel tooth and TCI tricone bit) 2.PDC bit(steel body and matrix body PDC bit) 3.rock hole opener for vertical and horizontal directional drilling, rock reamer 4.single tricone cutter 5.other drilling tools(drill rod, mud motor, drag bit, etc)
product name: tungsten carbide insert tricone rock bit diameter: 135/8 inch IADC: 537 bearing: rubber sealed bearing connection thread: 65/8" API Reg pin usage: water, oil, gas well drilling application formation: medium soft rock formation Company profile Hebei Crossing Drill Bit Manufacture CO.,LTD is a professional supplier of drilling tools,including tricone bit,PDC tricone bit,Hole opener,single cone bit and so on.With years of study and refining of the introduced technology, we have succeeded in the field of product research with proprietary intellectual property rights.Also, we have made major breakthrough in the lines of analogue simulation in bottom-hole flow field,profile optimization,design of inserts arrangement and low torque,material and manufacturing techniques etc. As a result, our products own better characters of service and ranges of application.Mainly used for oil and gas,mining,geothermal,construction and so on. The products of our company have achieved industrialization and serialization.Besides our company has always laying importance on the technical exchanges and cooperation with the counterparts both at home and abroad.Our products have been sold all over the world, including the United States, England,Canada,Brazil,Russia,Italy,Iran,Saudi Arabia,Korea, India, and Poland and so on. The main products we can provide: 1.tricone bit(steel tooth and TCI tricone bit) 2.PDC bit(steel body and matrix body PDC bit) 3.rock hole opener for vertical and horizontal directional drilling, rock reamer 4.single tricone cutter 5.other drilling tools(drill rod, mud motor, drag bit, etc)
product name: milled tooth tricone bit diameter: 15 inch IADC: 114 bearing: rubber sealed bearing usage: water well drilling application formation: soft formation Company profile Hebei Crossing Drill Bit Manufacture CO.,LTD is a professional supplier of drilling tools,including tricone bit,PDC tricone bit,Hole opener,single cone bit and so on.With years of study and refining of the introduced technology, we have succeeded in the field of product research with proprietary intellectual property rights.Also, we have made major breakthrough in the lines of analogue simulation in bottom-hole flow field,profile optimization,design of inserts arrangement and low torque,material and manufacturing techniques etc. As a result, our products own better characters of service and ranges of application.Mainly used for oil and gas,mining,geothermal,construction and so on. The products of our company have achieved industrialization and serialization.Besides our company has always laying importance on the technical exchanges and cooperation with the counterparts both at home and abroad.Our products have been sold all over the world, including the United States, England,Canada,Brazil,Russia,Italy,Iran,Saudi Arabia,Korea, India, and Poland and so on. The main products we can provide: 1.tricone bit(steel tooth and TCI tricone bit) 2.PDC bit(steel body and matrix body PDC bit) 3.rock hole opener for vertical and horizontal directional drilling, rock reamer 4.single tricone cutter 5.other drilling tools(drill rod, mud motor, drag bit, etc)
