Oil putty BEIGE. Tough, malleable sealant for surfaces such as wood, metal and glass. Size 1 kg 2.5kg BEIGE oil putty. Tough, malleable sealant for surfaces such as wood, metal and glass. Skin formation time approx. 12 â?? 30 days. Temperature and humidity are very important. Must be painted over with primer or glaze after 4 â?? 6 weeks at the latest. Weight n/a Size 1kg, 2.5kg
Gardener's putty. Tough, malleable sealant for surfaces such as wood, metal and glass.
Refractory bricks, high alumina bricks, fire clay bricks, sk 34 fire bricks, sk 36 fire bricks, acid resistance bricks,insulating bricks, hfk bricks, cfi bricks, special shaped refractory burner block, refractory tiles, refractory tundish well blocks, refractory nozzle, refractory castables, medium purity high purity castables, low cements castables, refractory mortar, refractory cements, ceramics fiber blankets, ceramics fiber boards, crushed refractory bed materials, bottom pouring sets.
Luxes Natural Floor Finish is a cement-based product that can be applied on the floors. This product is specially designed to replace the use of high-cost floor tiles. The latest innovation of the decade to save time and money with the option of different architectural designs and finishes.
28Kg Bucket Luxes Wall Putty is an all-purpose ready mixed wall putty, suitable for any kind of interior use. Plastering, Topping, Tapping, gypsum boards, as a joint compound &etc
Luxes Wet Look Sealer is an eco-friendly water-based, hard-wearing clear sealer designed to repel moisture and water from construction materials. It can be applied on both interior and exterior floors & walls such as Titanium floors + Walls, Granite floors, cement pavers, natural stone surfaces + slate, terracotta, and clay tiles.
An top coat. Cement Base silica mixed solid powder product. Hand trowel. Both rough and smooth surface can be obtained.
JK TileMaxX - General Purpose Tile Adhesice TA11
JK TileMaxX - High Performance Tile Adhesive TA33
JK TileMaxX - Supreme Flexible Tile Adhesive TA44
JK BlockMaxX - Concrete Block Mortar MM11
JK BlockMaxX - Light Weight Block Mortar MM22
The cementing plug is used to separate the cement slurry from the mud. It can prevent the mud from blending into the cement slurry to influence the cementing quality. Structure: conventional cementing plug & special cementing plug Conventional cementing plug is divided into top plug and bottom plug. Special plug has top/middle/bottom plug used in two-stage cementing, drill pipe plug and hollow plug used in drilling liner cementing and composite plug used in composite casing.
Jacobs 29 butly Mastic seal Tape is composed of Conforrtable, duable, tacky mastic with an easy - tear release liner, Which is designed for quick and easy insulating, padding and sealing of objects that need to be protected from adverse conditions. used with pvc tape it is suitable of cable =s, buried cables and pipes. Product Feature Highly comfortable to any irregular surface and object Wide temperature Stability while maintaning its sealing properties Good adhesion and sealing characteristics to metals syntheic cable insulation and jackets Excellent weather resisant, waterproof, sealing properties Application Range Sealing ducts and cable end seals Sealing high voltage cable spice and termination accessories Padding irregular shaped connections Used for filling and sealing installation holes of air conditioning or other equipments Specification 38.1 mm (W) X 1.524 m (L) X 3.175 mm (T) Size can be available as per Customers Request.
Universally applicable, low-foaming padding auxiliary for continuous and semi-continuous dyeing processes; wetting and deaerating agent for dyeing from long liquors; for dyeing cellulosic fibres and their blends.
PCE superplasticizer is the newest generation superplasticizer used for concrete in domestic and abroad.It is based on molecular designs and adsorption capacity of polycarboxylate,we do R&D and successfully produce water reducing and retention type polycarboxylate superplasticizer for concrete.With initiating systerm and reaction conditions,we achieve high adaptability. Polycarboxylate Superplasticzier we produce types as below: 1. High water reducing type (normally they can be satisfied for concretes' requirements): JH03 basic standard type(under most exported.) JH09 viscosity adjustment is better than JH03,water reducing ratio is lower than JH03,(suitable for high clay content ratio of cement,under most exported.) JH15 water reducing ratio is higher than JH03,performance is better than JH03,suitable for high strength concrete.(New Research and technology higher than JH03.) 2. Water reducing and slump retention type JH02 water reducing and slump retention type.(New Research on base of JH03.) 3. High slump retention type JH06 basic standard type,mix with JH03 and JH09 if concrete's slump retention is not satisfied.(under most exported.) JH06K higher slump retention performance than JH06,price is higher than JH06,mixing with JH03 and JH09 if concrete's slump retention is not satisfied.(under most exported.) JH16 Better performance and different technology with JH06 and JH06K,mixing with JH03,JH09 and JH15 if concrete's slump retention is not satisfied.(New Research and technology to satisfy JH15.) Exporting loading: 20'GP container loading: 1. 220kg/drum, 80 drums 17.6 T 2. 1150kg/drum,20 drums 23 T 3. 20-25tons/flexitank. 20-25 T
Refractory mortar is a specially engineered mixture of sand, calcium aluminate,cement,and fire clay.It is used to lay fire brick in places that are exposed to extremely high temperature. Refractory mortar produced from fine grained refractory aggregate, refractory powder, binder and other additives and used for building and bonding the refractory bricks, and also repairing of furnace lining, which is mainly used in glass furnaces, hot blast furnaces, coke ovens, soaking furnaces, heat exchange, boilers and other industrial kilns. Characteristics of Mortar: High temperature strength High thermal stability Good resistance to slag erosion Good anti-stripping performance Long service life.
Our air-set refractory mortar is ready-to-use for lining refractory bricks and insulation bricks. It contains refractory materials and binders to provide an excellent adhesiveness after drying in the room temperature, and excellent Bonding strength after 1200~1500 sintering. It is highly suitable for bonding of insulation bricks and refractory bricks. It is used to seal and repair furnaces, combustion chambers, boilers, stoves, flues, stoves, ducts, chimneys, and many other furnaces and refractory applications. Ready to use Easy application Refractory wet mortar High Temperature Refractoriness
JANTA Group provides Refractory Boiler Bed Material (Refractory Grog) of Low Ferric High Temperature product, which is processed from selected super heat duty refractory aggregates of moderate alumina contents and of highly dense texture. This very special Bed Material of Refractory Aggregates fired at a temperature of 1400 Centigrade has many special characteristics that make it a perfect material for obtaining smooth and perfect fluidization in Fluidized Bed Combustion boilers with high economy of operations. Special Characteristics: Exceptional Chemical Purity with Low Alkali and Low Iron Contents Fully Screened Material with Accurately Controlled Particle Size Distribution Free From Dust/ Fine & Over Sized Particles Perfectly Controlled Particle Density and Bulk Density
Calcium silicate insulation board is produced from basic material calcium and silicon and provides excellent service in demanding fire-proof applications. Calcium silicate boards are widely used in pipes and thermal equipment, power station, petrochemical, foundry industrial as thermal insulation. It is also used as back-up lining for industrial furnaces.. Calcium Silicate Boards are designed to withstand high temperature as well as feature superior structural strength. Further, the use of hydrous calcium silicate makes these blocks suitable for use in systems operating up to 1200F. Available in the inorganic and noncombustible finish, this also meet physical and thermal property requirements as per defined standards as well as support corrosion resistance to outside surfaces of pipe and equipment. Also suitable for use in fire endurance applications, these are available in finish forms of the preformed block and preformed pipe. These are suitable for use in industry sectors like chemical plants, refineries, steam electric power plants and others.
