Ature:remove all oil or grease, soluble contaminants and other foreign matter
All surfaces to be coated should be clean, dry and free from contamination
If applied on rusty surface, rusty layer thickness should be below 50mm, other than bottom surface processing requirements, without acid and sandblasting processing, catalytic reaction, to get black protective layer and solvent (acrylic acid, polyurethane, epoxy resin, alkyd resin, amino paint or water-based paint) match well, will not occur and paint color bleeding
Apply in nice weather, don't let coating contact any liquid like water or other solvent before completely dry
No painting be carried out in rainy day outdoor
If above 85% humidity please stop painting
Temperature of substrate should be above 5¡ãc
Lower temperature might not dry or cause long time to dry
•air spray:nozzle orifice range: 1.5 to 2.5mm
Nozzle pressure range: 0.3 to 0.5mpa
•airless spray:nozzle orifice range: 0.4 to 0.5mm
Nozzle pressure range: 12 to 15mpa
•features:brush: use soft brush
Recommended finish: rsl series
Storage temperature: 5 to 30¡ãc in well ventilated warehouse
Stir thoroughly before painting
Don't use any steel or other metal stick to stir paint
Can be applied directly on rusty steel( rust layer ¡ü45um)!
Color and appearance: grey or others
Coating thickness um: 50¡à5mm
Solid content % : 69¡à3%
Overcoating interval: minimum: 4 hours max: unlimited
Recommended substrate conditions and temperature:
1.Remove all oil or grease, soluble contaminants and other foreign matter. All surfaces to be coated should be clean, dry and free from contamination.
2.If applied on the rusty surface, the rusty layer thickness should be below 45 um
3.Apply in good weather, don¡¯t let coating contact any liquid like water or other solvent before completely dry. No painting be carried out in rainy day outdoor , if the humidity is above 85%, please stop painting
4.The temperature of substrate should be above 5¡ãc, lower temperature might not dry or cause a long time to dry
Air spray:nozzle orifice: 1.5-2.5mm
Nozzle pressure: 0.3-0.5mpa
Airless spray:nozzle orifice: 0.4-0.5mm
Nozzle pressure: 12-15mpa
Brush : use soft bursh
Recommended finish: rsl series finish
Shelf life: 12 months
Over coating time
Substrate
Temperature 5¡ãc 15¡ãc 25¡ãc 35¡ãc 45¡ãc
Minimum interval 24hrs 7hours 4hours 3hours 2hours
Maximum interval Unlimited storage temperature : 5-30¡ãc in well ventilated warehouse
Reinforcement filler in elastomers
Rheology and thixotropy control of liquid systems, binders, polymers, etc.
Used as anti-settling, thickening, anti-sagging agent
Improvement of free flow and anti-caking characteristics of powders
High transparency
Aadhya shellac as a leading manufacture , producer, supplier and exporter of shellac, shellac flakes, dewaxed shellac flakes, dewaxed bleached shellac powder, bleached shellac , shellac buttons, seed lac, and other shellac products in india since 2000.
Shellac is being used in fruit coating, french polish, varnish, enteric coatings , food coating , confectionery glaze , tablet coating , medicine coating printing ink , wood polish , surface coating, and many more purpose.
Aadhya shellac as a leading manufacture , producer, supplier and exporter of shellac, shellac flakes, dewaxed shellac flakes, dewaxed bleached shellac powder, bleached shellac , shellac buttons, seed lac, and other shellac products in india since 2000.
Shellac is being used in fruit coating, french polish, varnish, enteric coatings , food coating , confectionery glaze , tablet coating , medicine coating printing ink , wood polish , surface coating, and many more purpose.
Disposable painting-overall with hood
-size s, m, l, xl, xxl
-extremely comfortable with elastic sleeves and trouser legs
-abrasion resistant, hard wearing, antistatic, breathable fabric.
-material is polyester
-zipper on the front, hidden
Protects your walls from fungus and humidity, anti-termite, fire resistant, anti-microbial and anti-bacterial.
Useful for maintaining cleanliness and hygienic atmosphere in restaurants , hotels, ships, office and residential premises.
Kleenkot does not merely inhibit the growth but kills broad spectrum of bacteria on its surface.
Protects surface applications from industrial accidents and operational hazards like fire, corrosion and chemical reactions.
Metalkot is heat and abrasion resistant
Metalkot retains the gloss on the surface.
Protects furnishings, fabrics, curtains, mattress, coir, uphoistery, draping material, carpets etc against fire.
Also useful for clothing
Doesn’t affect the colour, texture and flexibility of the fabric.
The effect of the coating is retained even after dry cleaning.
The equipment adopts the resistance heating in the vacuum chamber, to melt and vaporize the metal wire (aluminum wire) cling to the resistance wire. The vaporized metal molecule deposit on the substrates, to gain the smooth film as well as high reflectivity. Thus the surface of the items can be decorated and beautified.
Characteristic: reasonable structure, even film, good-quality film forming, quick pumping speed, the cycle of short, high efficiency and easy operation, low energy consumption and performance advantages of stability.
Applied industry: Widely used in automotive, audio and various small appliances, computers, clocks and watches, toys, cell phones, reflective Cup, cosmetics, toys, tableware, sanitary ware, shoe heel, ABS, PS, PP, PC, PVC, PET, nylon, metal, Boli, glass, ceramics, TPU, etc.
Electroplating effects: general electroplating-face, dumb-(semi-mute, all dumb), the electroplating process wrinkles, lampworking, raindrops, seven colors
Coating color:gold, silver, red, blue, green, purple, multi color, and so on.
Coating color: gold, silver, red, blue, green, purple, and so on.
All vacuum coating machines are environmental prodection products and sooner or later will replace traditional galvanization industrial.
Technical parameter:
Mode
Dimension
ZZ-1200
ZZ-1400
ZZ-1600
ZZ-1800
1200*1400mm
1400*1600mm
1600*1800mm
1800*2000mm
Mainly Application
Plastic decorative coating , glass decorative coating and protective film coating
Film Type
Semitransparent film, non-conducting film, gold, silver, red, blue, green, purple, seven color, etc.
Power source Type
Thermal evaporation power, ion bombard power, RF power
Vacuum chamber structure
Vertical double/single door, horizontal single door, pump system postposition
Ultimate vacuum
8.0*10-3Pa
Vacuum system
Diffusion pump +Roots pump +Mechanical pump +Holding pump
Pump time
Pump from atmosphere to 5.0*10-2, 6 minutes
Workpiece motion mode
Public rotation/Frequency control
Control mode
Manual/Automatic all-in-one mode, Touching screen+PLC
compress air
the pressure is 5~6kg.
water-cooling system
Cool water 5~25 supplier, the flux is 5T/H and the pressure is 0.15~0.25MPa.
Features
Bright delicate aluminum coating, coating speed, simple operation, equipment stability, and the production of high-grade plastic decoration products indispensable a necessary equipmen
Ceramic gold coating machine can coat tin, tic, zrn, crn, ti, ni, cr, cu and other compounds film, multi-layer super-hard film, nitrogen-doped titanium film and the alloy film, and in a very short time to complete all the machining process, it is a highly efficient multi-functional coating equipment.
Property:
1. Excellent chemical resistance
2. Excellent electric insulativity
3. Excellent adhesive force
4. High degree of hardness - good mechanical property
Application used for :
1. Coating metal cabinets,
2. Electric distribution boards,
3. Lighting components,
4. Metal shelves,
5. Air conditioners,
6. Office furniture.
Solidifying condition: 20min/180-190 degrees.
Trademark: rengui
Packing: 20kgs/carton or 25kgs/carton
Origin: china
Production capacity: 600 tons/month
25kgs/carton, sealed plastic bags with brown carton
Property:
1. Excellent chemical resistance
2. Excellent electric insulativity
3. Excellent adhesive force
4. High degree of hardness - good mechanical property
Application used for :
1. Coating metal cabinets,
2. Electric distribution boards,
3. Lighting components,
4. Metal shelves,
5. Air conditioners,
6. Office furniture.
Solidifying condition: 20min/180-190 degrees.
Trademark: rengui
Packing: 20kgs/carton or 25kgs/carton
Origin: china
Production capacity: 600 tons/month
Property:
1. Excellent chemical resistance
2. Excellent electric insulativity
3. Excellent adhesive force
4. High degree of hardness - good mechanical property
Application used for :
1. Coating metal cabinets,
2. Electric distribution boards,
3. Lighting components,
4. Metal shelves,
5. Air conditioners,
6. Office furniture.
Solidifying condition: 20min/180-190 degrees.
Trademark: rengui
Packing: 20kgs/carton or 25kgs/carton
Origin: china
Production capacity: 600 tons/month
Plative PLP4500 plating layer protective paint
Brief description
Plative PLP4500 plating layer protective paint, is designed to protect the plating layer by improving abrasion resistance, scratch resistance, chemical corrosion resistance, insolation and heat stability.
The paint of transparent has no effect on the color of plating layer, besides the paints of colorful can make the plating layer with different coloration.
Operational guidance
Prefabricated, diluted plative PLP4500 to a proper consistency and add 15% -25% to total plative SN30, mix completely.
Clean and dry the plating layer, make sure no oil, no dust. To paint the layer with prepared paint by spraying, immersion or drawing. Then forced dry at 120 ¡æ in 50 minutes, or air dry in more than 12 hours.
Annotation
Before use, low-speed mixing of plative PLP4500 is required; dilute the product with special solution alative PLP4500, or else it could lead to paint deterioration.
Plative PLP4500 plating layer protective paint
brief description
Plative PLP4500 plating layer protective paint, is designed to protect the plating layer by improving abrasion resistance, scratch resistance, chemical corrosion resistance, insolation and heat stability.
The paint of transparent has no effect on the color of plating layer, besides the paints of colorful can make the plating layer with different coloration.
operational guidance
Prefabricated, diluted plative PLP4500 to a proper consistency and add 15% -25%to totalplative sn30, mix completely.
Clean and dry the plating layer, make sure no oil, no dust. To paint the layer with prepared paint by spraying, immersion or drawing. Then forced dry at 120 in 50 minutes, or air dry in more than 12 hours.
Annotation
Before use, low-speed mixing of plative plp4500 is required; dilute the product with special solution alative PLP4500, or else it could lead to paint deterioration.
