Electrical parameters Ratio 1000: 1 or 2000:1 (customized) Accuracy class 0.1%, 0.2%, 0.5%, 1% Primary current 0 - 1000A AC Secondary voltage 0-10V AC (customized) Max. Cont. Input current 1200A Over voltage category CAT III 600V Output signal (AC current) 250mA, 500mA,1A,5A AC at nominal input current Output signal (AC voltage) 1V, 5V, 10V AC at nominal input current Frequency range 40Hz-2000Hz Dielectric strength 3KV 50Hz/60Hz at 1 minute Temperature range '-40C to +55C Output 2.5 meter cable with D01 connector Max. voltage not insulated conductors 600 V Standard EN 61010-1, EN 61010-2-032, IEC60044-1, IEC61869-2 Installation clamp type Output mode lead output(2.5m, 5m or 10m) Mechanical parameters Dimensions (L x W x H) (mm) 163 x 310 x 34 Weight (g) 900 Holding wire diameter (mm) 110 Max. jaw opening (mm) 110 Jaw color Black Material PC+ABS, UL94 V0
Capacity IN Tones Jaw Openng A Plate ADMIT C Body DIA B CAM DIA Ring Size d X D Weight Per Pair Kgs Pair Each 1 0.5 50 150 40 16 16 X 75 12 2 1 60 170 45 16 20 X 85 13.5 3 1.5 70 200 55 20 22 X 95 28.5 5 2.5 85 260 65 25 25 X 95 40 10 5 95 300 90 32 32 X 135 78 20 10 150 400 120 40 45 X 200 160
SL- 450 Front and Side View Sealinkers Clamps Each clamps has a product Identification Code for Material traceability, the name Sealinkers or SL, and a size forged into it. Entire Clamps are galvanized / Powder Coated to resist corrosive and rusting action. Only Genuine SL Clamps have a Yellow colour for instant recognition. All Clamps have rolled threads and extra heavy nuts. Rope Size Dimensions (mm) Min No. of Clamps Amt. of Rope to Turn Back in (cm)P (in.) (mm) A B C D E F G H 3/8 9-10 11.2 38.1 19.1 25.4 23.1 19.2 41.4 49.3 2 16.5 1/2 13 12.7 47.8 25.4 30.2 28.7 22.4 48.5 58.0 3 29.2 5/8 16 14.2 60.5 31.8 33.3 34.0 23.9 52.5 63.5 3 30.5 5/4 18-20 15.8 70.0 36.6 38.1 35.8 26.9 57.0 72.0 4 46 7/8 22 19.1 79.5 41.2 44.5 40.4 31.8 62.0 80.5 4 48 1 24-26 19.1 89.0 46.0 47.8 45.2 31.8 67.0 88.0 5 66 1 1/8 28-30 19.1 98.5 51.0 51.0 48.5 31.8 71.5 91.0 6 86 1 1/4 32-34 22.4 108 45.0 58.5 55.5 36.6 79.5 105 7 112 1 3/8 36 22.4 118 58.5 60.5 58.5 36.6 79.5 106 7 112 1 1/2 38-40 22.4 125 60.5 65.5 62.0 36.6 86.5 113 8 137 1 3/4 44-46 28.7 146 70.0 77.5 74.5 46.0 97.0 134 8 155 2 48-52 31.8 164 76.0 86.0 83.5 51.0 113 149 8 180 Note Refer to table I in following these instructions. Turn back specified amount of rope from thimble or loop. Apply first clip one base width from dead end of rope. Apply U-Bolt over dead end of wire rope - live end rests in saddle (Never Saddle a dead horse!).Tighten nuts evenly, alternate from one nut to the other until reaching the recommended torque.
DSQ Vertical Plate Lifting clamps are used for lifting and turning over plates from horizontal to vertical positions. DSQ Vertical Plate Lifting clamps are made with hardened steel jaws for firm grip and proper locking. DSQ Vertical Plate Lifting clamps in a small easy to handle tool, incorporated with a spring lock which facilitates attaching of the clamps to the plates. Model WILL Opening (mm) Weight (Kg) DSQ1 1 50 3.7 DSQ2 2 55 6.3 DSQ3 3 70 10.5 DSQ5 5 90 19.3 DSQ8 8 130 40 DSQ12 12 150 52 DSQ16 16 160 55 Warning Do not exceed Working Load Limits. Avoid Superficial Gripping. Do not exceed specified angle of Lift (Not more than 60). Check the cams periodically for excessive wear and tear and reject if found unsafe.
Model SL - PLC Model : SL - PLC CAPACITY Shackle Size Plate Size EACH PAIR 1.5 3 16 X 19 16 2.5 5 16 X 19 25 4 8 19 X 22 28 5 10 19 X 22 32 7.5 15 25 X 28 35 10 20 25 X 28 45
I - Beam Clamps (Model: SL - IBC) Capacity Flange Width 1 3" - 7" 2 3" - 7" 3 3" - 12" 5 4" - 13" 10 4" - 13" 15 5" - 16" 20 5" - 16" Spare Parts for IPTK Safety Lifting Clamps: Order No. 1. Body Complete 1041 2. Hoisting Eye Complete 1235 26. Hingeshaft Complete 0232 36. Screwed Spindle Complete 1362 Important Features Lower construction height due to integrated traverse. Reduced Stress on I - Beam flange due to specially designed clamp jaws. Adjustable for a wide range of I - Beam widths & Profiles (INP, IPE & IPB) Strong Industrial Design Clamp corresponds to standard specification for vertical load pick-up. Each quipment is serially numbered, tested by a competent authority 50% overload & is given Test Certificate. Optional feature special ofshore version model IPTKO (including 3.lB certificate)
Bull Dog Grips (ISS) IS: 2361 / 1970 Drop Forged Steel Wire Rope Bull Dog Grips Note : For intermediate sizes of wire ropes, the next larger size of bull dog grip shall be used.
1.Product Name: H7 clamping ring 2.Product Type: H7 adaptor(NY) 3.Material: SUS 430 4.Usage: H7 PX26D lamp 5.Product Dimension: Height: 4.5+0.2mm Outer Diameter: 15-0.1mm Eccentricity: 0.8±0.06mm 6.Product Feature: Outgassing Test: passed. 7.Packaging Details: 5000 pcs/carton. Our company: Invitech is a company committed to the manufacture and development of Metal stamping parts. The products widely used in Auto, Electric appliance, Electronics ects...Through years of operation, we have established solid, long-term and cooperative relationships with clients from India, Korea also Europe by providing manufacturing services ranging from parts to complete appliances and have become a professional metal stamping parts supplier. FAQ: 1.How many types of H7 adaptor you have? A variety of types, we customize the component for each customer. 2.Do you have deviation test equipment? No, my customers do the deviation test. 3.How do you make sure the positive result of deviation test? We have rich experience adjusting the dimension of H7 adaptor according to your capsule shape to pass the deviation test.
ISO Springs|Mould clamps|Die part Chinese- Dalian Mintadely mould Co., Ltd. was established in Dalian in 2006, Mainly engaged in the design and manufacture of plastic mold China, injection mold China, China mould, automobile parts mold of semiconductor, IC connector, lead frame electrical connection and motor fixed rotor, as well as various precision mold spare parts and spare parts. We guarantee to provide customers with excellent design and first-class quality products at any time and occasion. ISO 9001:2008 Certified Your Trusted Plastic Molds, Injection mold, Die Parts, Die Casting mold Partner in China. We are not only make molds and parts for you, but also your technical supporting team. Who using our mould: Meredes-Benz, BMW, Audi, Honda, Toyota, Volkswagen, Nissan, Mazda,etc. We have design department, laboratory and testing center and a R&D team with a strong technical and experienced to ensure continuous improvement and innovation of processes and products to meet the different needs of different customers. Apply ERP system, implement standard management in process, quality, delivery, product, service. Ensure customer's product quality and delivery time. With many years of experience in mold design, manufacture, molding, leading technical solutions and perfect quality service, we can keep our eyes on the global market while consolidating existing customers.
@ Model No. M8021, M8010 @ Made in Taiwan #Key Features 1. Zinc plated frame & bolts even better rust-proof. 2. Heat treatment with bolt front end, tight fasten with channel steel for an anti-shake, loosing prevent factor. 3. Fastening torque for general steel: 75 kgs/cã?¡ be aware keeping from over fastened. #Main Export Market AFRICA ,ASIA ,AUSTRALASIA ,C-AMERICA ,EUROPE ,MID-EAST ,N-AMERICA ,OTHER ,S-AMERICA
Strain Clamp Overhead Line Fittings Power Line Hardware Specifications: Strain clamps are used to fix conductors and ground wires to insulators or link fittings to tower arms and substation structures. There are two basic systems of strain clamps, 1. Detachable clamps, such as wedge-type tension clamps, thimbles, bolted type tension clamps, which allow for subsequent adjustment. 2. Non-detachable clamps, such as compression dead-end clamps which require absolute matching to the conductor length. The type of strain clamps are including NLL-1, NLL-2, NLL-3, NLL-4 and so on.
PG Clamp Overhead Line Fittings Power Line Hardware Specification: PG clamp is known for parallel groove clamp, especially used in transmission line to hold transmission conductors in parallel. PG Clamp solutions offered provides for secure holding support of transmission conductors. These parallel groove clamps come with features like high corrosion-resistance, aluminum alloy construction in hot forged finish, stainless steel based bolts & nuts in hot-dip galvanized finish, corrosion protected washer support, precision developed pressure pads with spring washers in hot-dip galvanized finish, copper based conductors and others. We can also custom design and develop these clamps as per the specific requirements of the customers.
Dead end grip for OPGW Component Inner armor rods, outer armor rods, thimble, U-shaped hanging loop, Extensioe Rods, bolt, nut, etc. Characteristic 1. Stress is distributed equally, without stress focus. It can protect optical cabl-es very well. 2. Under the condition of not exceeding the intensity of cable's side pressure, it has higher grip power for the cable, and can support higher tensile force. 3. The grip power for the cable is not less than 95% of rating's pulling resisting intensityof the optical cable, completely satisfying the needs of setting up the cable. Conditions For The Usage 1. Terminal poles/towers; 2. Corner poles/towers; 3. Dead-end poles/towers; Intensity According to the requirement of customers, 30kN, 70kN, 100kN, 120kN, etc, can be supplied. Select Chart Model Grip(KN) Length of Inner Armor Rods(mm) Length of Outer Armor Rods(mm) Estimated Weight(KG) Color ONZ-60-* * 60 1900 1500 2.9 Yellow ONZ-70-* * 70 2000 1600 3.5 Yellow ONZ-80-* # 80 2200 1700 4.2 Yellow ONZ-90-* # 90 2400 1800 4.3 Yellow ONZ-100-* # 100 2500 1900 4.5 Yellow ONZ-120-* # 120 2600 2000 5.0 Yellow Note: representing the outer diameter of the optical cable (mm).
Product Name Clamp Saddle With Bolt All sizes are available. MOQ 200 Pieces
We supply all the complete DIY hose clamps range. Please contact us for the full product line-up description and/or more information.
We supply the complete hose clamp range. Please contact us for the full product line-up description and/or more information.
Saddle HDPE Pipe Quick Repair Clamps Water Supply use Material : HDPE Standard : DIN Standard Connection : Butt fusion&socket fusion Working Pressure : SDR11,SDR12.5, SDR13.6,SDR17 Color : Black or customized Applications: 1. City and town dringking water supply system 2. Sea bed water supply system 3. Food and chemical industry 4. Replacement of cement pipes and steel pipes 5. Argillaceous silt, mine,mud transportation 6. Irrigation and garden green pipe networks and sewage treatment 7.Nature gas supply system Find trusted of HDPE Fitting, HDPE Manifold, PE Compression Fitting, HDPE Saddle Quick Repair Clamp etc. Any requirements and problems can ask us at any time. Waiting to create business relationship with you Features: 1. Chemical stability. Polyethylene does not erode to acid, alkali and salt. In addition micro-organism like bacteria or seaweed cannot grow in Polyethylene material. 2. Hygiene. Optimal conditions as pipes for providing portable water are met not only in that purity of contents can be maintained but also the taste of water does not change. 3. Fluidity. , PE water pipes smooth inner walls prevent blocking of pipes and minimize loss of water. 4. Flexibility. , PE water pipe is convenient to install because curved fittings don not have to be used at bent position and flexibility is maintained at low temperature. 5. Light weight. , PE pipes can be easily handled and installed because the weight of PE water pipes is just 1/7 of steel pipes. 6. Perfect connection. Quick and perfect laying of pipes is possible because heat fusion connection is used for PE water pipes. 7. Non-corrosiveness. PE pipes do not corrode by chemicals, electricity, damp ground and salt. 8. Impact endurance. The pipes don not break by outer impact due to the characteristic of the material. 9. Cold endurance. The pipes do not break up to -70 degree 10. Long life. The pipes can be used for at least 50 years. 11.Green intiative,PE is a recycled material,environment friendly. 12.Low system cost,less maintenance costs,reduce the cost for the project Rongde is a professional manufacturer of HDPE Plumbing, PPR Plumbing, Pert Tubing, PEX Tubing, PVC Plumbing, Aluminium Plastic Composite Pipe, Shower Hose, Home Floor Heating Tubing, Bathroom Shower Hose, Industry Agriculture HDPE Plumbing etc. Our products have high quality and competitive prices.
No.: SIP22 Price: $65,00 SIP22 key clamp Support Fiat SIP22 keys.
C130-Clamp with 32-35mm diameter tubes Skymear tower truss systems are all based on standard SkymearStructures truss. Extending your inventory to encompass more complex systems,like towers or roofs is a cost-efficient process. Overview Skymear truss clamps are based on standard SkymearStructures truss. Extending your inventory to encompass more complex systems (like towers or roofs) is a cost-efficient process, proceeding as a step-by-step investment. You only need to buy the additional parts, such as base or top sections to complement the truss to use them as tower truss. This approach offers extraordinary flexibility and facilitates optimum use of your existing trusses. All our aluminum trusses are made in China.We can do OEM for your customized service and provide our factory price directly to you. Key Benefits l Compact, light, mobile product l Great strength to weight ratio l Safe and big loading capacity l No deflection in its connection point l Welding points are smooth l Fast and easy to assemble l Powder coating or a high gloss/hand polished design Aluminum Trusses Mobile Truss Clamps, Riser Folding Stage, Rubber Cable Protector Supplier All our aluminum trusses are made in China. We can do OEM for your customized service and provide our factory price directly to you. If you want to know more about our products, you can contact us.
Down Lead Clamp Metal Downlead Clamp ADSS Cable Fittings 1. Usage and characteristics Down Lead Clamp is used for fixation of OPGW and ADSS onto the pole/tower. It is suitable for all kinds of cable diameter; the installation is reliable, convenient and fast. Down Lead Clamp is divided into two basic types: pole used and tower used. Each basic type is divided into elector-insulating rubber and metal type. Elector-insulating rubber type Down Lead Clamp is generally used for ADSS installation, while metal type Down Lead Clamp is generally used for OPGW installation. 2. Product Specification ItemTypeAvailable Dia.of Cable (mm)Note Rubber type Down Lead Clamp for towerTGY 1110-T9.0-11.1For ADSS Cable TGY 1330-T11.2-13.3 TGY 1550-T13.4-15.5 TGY 1800-T15.6-18.0 Metal type Down Lead Clamp for towerTGY 240-T7.4-20.0For OPGW Cable Rubber type Down Lead Clamp for poleTGY 1110-H*9.0-11.1For ADSS Cable TGY 1330-H*11.2-13.3 TGY 1550-H*13.4-15.5 TGY 1800-H*15.6-18.0 Metal type Down Lead Clamp for poleTGY 240-H*7.4-20.0For OPGW Cable Note: H*---Dia.of pole(mm) ModelH1H2H3H4H5 Suitable for Max Dia. For pole(mm)3104606008001000 3. Packing/Shipping/Terms of Payment Packaging: preformed guy grip according to the concrete product cartons, wooden cases(as customer's requirements) Delivery: usually, it will take about two weeks for the order of 10000sets for production Terms of Payment: By T/T
