Find Verified Glass Glass Products Suppliers, Manufacturers and Wholesalers

Alkali-resistant fiberglass mesh is woven with fiberglass yarn and coated by acrylic acid or PVC. This product has perfect corrosion-resistant, high strength and good thermal insulations, which is mainly used to reinforce wall materials,gypsum,stone, mosaic,ceramic, cement, etc,especiallyfor outside and inside wall heart insulation system.lt is an ideal engineering material in construction

Mesh size:2.85mmí½12mm,
Area weight:60gO,70gO,75gO,80gO,85gO,90gO,110gO,125gO,145gO,
152gO,160gO,165gO,180gO,330gO,470gO,600O,etc.
Weave:leno,plain
Width:100cm(normal)50cm33cm20cmetc.
Roll length:50m100mm200m300m800m1000m
Color:white,yellow,green,blue,orange,red,etc


Packing:each roll is packed in shrink-wrap film or plastic bag,rolls on pallets.

Fiberglass sleeving
Type properties average voltage (v)
high breakdown volage, resistant temperature 200 . 7000
middle breakdown volage, resistant temperature 200 . 4000
Low breakdown volage, resistant temperature 200 . 2500

Fiberglass backing plate for flap disc:

Layer: 6-12
Type: T27, T28, T29
Size: 75mm, 85mm, 90mm, 95mm, 107mm, 117mm, 140mm,170mm, 220mm

Introduction:

Basic Materials: Epoxy resin, curing agent and alkali-free glass cloth

Specifications:

Performance: Good dielectric properties and machinability

Temperature Classification: Heat resistance is different according tot he raw material (B/F/H)GB/T 5132.1-2009 IEC61212-1:2006

Application:

It can be used as insulation structural components for electrical equipment. Can be made into a dry-type transformer coil insulation tube and transformer insulation end.

Brief introduction:
1. Producing procedure: Fiberglass yarn impregnated with epoxy resin etc, and then rolled in wet method, and then dried and consolidated.
2. Characteristics: It has excellent electrical and mechanical properties, low dielectrical loss, no deformation, chemical resistant etc. It can be used as main insulator on H grade dry type transformers, load tap changer, reactor, lightning protector, SF6 Inductor etc.
3. Heat resistance class: F,H

Fiberglass rods are high-strength, non-conductive cores for composite insulators, made from E-glass or ECR glass fibers with epoxy resin. They offer superior mechanical strength, electrical insulation, and corrosion resistance, making them ideal for high-voltage power systems.
Epoxy Fiberglass Rods are versatile and durable products that provide excellent high-voltage insulation and protection against extreme temperatures and impacts. Made of epoxy resin and fiberglass, these rods are designed to withstand high voltage and have excellent flexibility and UV resistance. They come in various diameters and are perfect for applications in high-voltage insulation, as well as other industrial and commercial purposes. With their excellent high-voltage insulation and superior impact and temperature resistance, Epoxy Fiberglass Rods are a great choice for those looking for a reliable and resilient product.

Features:

Product Name: Epoxy Fiberglass Rod

Color: Light green, brown, or customized colors

High quality, high voltage electrical properties

Various diameters available for customization

High UV resistance

High impact resistance

Explanation:

Material Composition: Made from epoxy resin and fiberglass, combining strength and flexibility.

Electrical Properties: Excellent high-voltage insulation, suitable for electrical applications.

Durability: High resistance to UV radiation, impacts, and extreme temperatures.

Customization: Available in various diameters and colors (light green, brown, or custom options).

Applications: Ideal for high-voltage insulation and other industrial or commercial uses.

Feature
7 inch Color LCD , Touch screen
Flow cell and Cuvette test mode compatible
Real time curve showing
7 wavelength , 90 test item pre-programmed
Memory for 10,000 sample results
Light source hibernate function making lamp life longer
RS232 interface, PC connecting

The traditional method of radiographic inspection for weld of oil and gas pipeline is to use radiographic source and film for transmission. However, with the improvement of quality control efficiency by the construction party, the method of film imaging can not meet the requirements of customers for efficiency. In addition, the film also has some problems, such as image processing, poor preservation, environmental pollution and so on.
Based on this situation, HATATEST independently developed the PT360 pipeline weld DR automatic detection system.

HATATEST Automatic DR Detection System for Pipeline Weld-PT360 is a kind of Automatic DR Detection robot who is similar with Transcan system in Russia, But HATATEST Automatic DR Detection System for Pipeline Weld-PT360 as the following highlights comparing with Russian Transcan :
-- Aluminum alloy chain spider, light and easy to carry
-- 400-1219 mm, any caliber can be used
-- Battery drive, maximum working time 12 hours
-- Software control (start and stop can be controlled manually by software, or automatic start and stop can be set)
-- Single-arm or double-wall transillumination
-- The whole installation process only takes 2 minutes
-- Real time imaging, greatly improved detection efficient
-- Image quality ISO 17636-2 Class B
-- Adjust the fixed device of the radiation source according to the customer's requirements, and match different radio sources

Up to 200 constant tests per hour
1000 patient test data
2000 test procedures can be saved
New concept test systems
Please check the attached product information.

Brief Introduction of the 30L rotary evaporator

30L rotary evaporator is a common laboratory equipment. It's consisted with motors, distillation flask, heating pots, receiving flask, condensers and so on. This device is mainly used for continuous distillation experiments under vacuum conditions. Our company designed 10L, 20L, 30L ,50L medium vacuum rotary vacuum evaporator for users to choose.
Main Features of the RE-3002 rotary evaporator

1. The main frame of stainless steel and aluminum alloy

2. Polytetrafluoroethylene and imported fluororubber combined seal

3. The real-time display of the vacuum is up to 0.098Mpa

4. GG-17 glass,High temperature resistance, anticorrosion

5. Continuous feed

Brief Introduction of the Jacket Glass Reactor

The series of reactor kettles is my company according to the actual requirements of customers and the standard production of new double glass reactor with cylindrical glass reactor body, which absorb the international and domestic advantages of similar products, while bold and innovative, not only easy to use one can easily move, , And the structure of innovative and practical, beautiful appearance generous, leading domestic; for modern chemistry, fine chemicals, bio pharmaceuticals, new materials, such as the synthesis of experimental and production of the ideal equipment. Specific specifications from 1L to 200L optional.
The working principle of the series reactor: double layer glass reactor inside the reaction material, but also can be vacuum to do the stirring reaction; sandwich can be connected to heat water, water or hot oil or electric sets to do heating or cooling; The reaction solution was controlled to evaporate and reflux.

Jacket Glass reactor principle is two parts, in the inner glass,the mix bar is continous stirring to make mixing or evaporating reaction under negative vacuum pressue. The stirring is under speed controlling. The jacketed glass could supply heating or cooling material to help the chemical reaction. Recently glass reactors has been widely used in chemical, biological and pharmaceutical experiment and prodcuction.