DongHongXin led amplifying ring adopts the new pom match +Gf glass fiber material processed by precision injection molding machine. The high precision between the sub-mother rings is better and the service life is longer.
DongHongXin square wafer ring is processed by slow wire processing with sus420j material. The surface of the wafer ring is polished and heat treated to make it more resistant to folding and flatness. It is more stable when bonding.
In the custom sus420 wafer ring you need to provide the depth of the film tray of your equipment, in order to determine the thickness of the sus420 wafer ring, in general, you buy the equipment manufacturer will tell you the parameters of the ring. If you have special requirements, you can tell Donghongxin Engineering here that you will design and process the sus420 wafer ring according to your needs.
Slip Ring Seal A slip ring seal is a type of mechanical sealing device used to prevent fluid or gas leakage in rotating machinery. It is typically used in equipment with rotating shafts, such as electric motors or generators, to provide a seal around the rotating shaft and prevent the leakage of fluids or gases from one side of the seal to the other. A slip ring seal is typically made up of a stationary component and a rotating component, and is designed to maintain a sealing interface as the shaft rotates. Performance and Purpose Slip ring combined seal is made up of low-friction PTFE composite slip ring and O-ring. It has the advantages of friction resistance, temperature resistance, high pressure bearing ability, high linear velocity, small friction force and long use-life. And which is applicable to dynamic and static seal of hydraulic and pneumatic system in aircraft, metallurgy, petroleum, chemical, textile, food industry and so on. Advantage The structure is simple, easy to install and can be used repeatedly The sealing performance is reliable and adjustable Different types of PTFE materials(Self pressed PTFE barrel material)can be selected according to the working conditions of sealing environment The working life of dynamic pressure seal is 5 ~ 10 times higher than that of conventional rubber sealing products, and the highest working life can reach dozens of times It can be used as oil-free lubrication seal The friction force is small, and the dynamic and static friction force are equal. The friction force is 1 / 2 ~ 1 / 4 of the O-type rubber ring, which can eliminate the crawling phenomenon of motion at low speed and low pressure. If you are looking for more details, kindly visit our website.
Casing Slips Type UC-3 are multi-segment slips with of 3 in/ft on the diameter taper slips(except size 8 5/8"). Every segment of one slip is forced equally while working.Thus the casings could keep a better shape.They should work together with spiders and insert bowls with same taper.The slips are designed and manufactured according to API Spec 7K.
There are three model of type B rotary slips(woolley style):B short,B Long and X Long. The unique torque transmitting design can directly transfer all the torque to the slips,avoiding the abrasion,prolonging the service life.The product is designed and manufactured according to API Spec 7K requirements.
Casing Slips Type UC-3 are multi-segment slips with of 3in/ft on the diameter taper slips (except size 8.5/8"). Every segment of one slip is forced equally while working. Thus the casings could keep a better shape. They should work together with spiders and insert bowls with same taper. The slips are designed and manufactured according to API Spec 7K.
Casing Slips Type UC-3 are multi-segment slips with of 3in/ft on the diameter taper slips (except size 8.5/8"). Every segment of one slip is forced equally while working. Thus the casings could keep a better shape. They should work together with spiders and insert bowls with same taper. The slips are designed and manufactured according to API Spec 7K.
Product Application The CMS casing slips are designed and manufactured in API 7K and SY/T 5049 " Slips for well drilling" .It is manufactured in a structure of multi-segment pieces with firm structure, light weight , and large holding range, which is easy to fit the changing of the external diameter of the casing pipes due to wear and tear.
Product Application The CMS casing slips are designed and manufactured in API 7K and SY/T 5049 " Slips for well drilling" .It is manufactured in a structure of multi-segment pieces with firm structure, light weight , and large holding range, which is easy to fit the changing of the external diameter of the casing pipes due to wear and tear.
Product Application The CMS casing slips are designed and manufactured in API 7K and SY/T 5049 " Slips for well drilling" .It is manufactured in a structure of multi-segment pieces with firm structure, light weight , and large holding range, which is easy to fit the changing of the external diameter of the casing pipes due to wear and tear.
Type DCS Drill Collar Slips There are three types of DCS Drill collar slips: S, R and L. They can accommodate drill collars from 3in (76.2mm) to 14in (355.6mm) O.D.. The handling size can be adjusted by changing the quantity of the inserts or slip body. The products are designed and manufactured according to API Spec 7K.
Introduce : Safety Clamps are tools for handling flush joint pipe and drill collar. There are three types of safety clamps: type WA-T, type WA-C and type MP.
The CMS casing slips are designed and manufactured in API 7K and SY/T 5049 " Slips for well drilling" .It is manufactured in a structure of multi-segment pieces with firm structure, light weight , and large holding range, which is easy to fit the changing of the external diameter of the casing pipes due to wear and tear.
1.Details of ring gauge: Material: Ring gauges are manufactured in both steel and tungsten Carbide,other material are availiable. Sizes: Ring gauges are manufactured from Inner Diameter 3.5 mm. to 60 mm. Steel ring gauges and master setting rings are manufactured from Inner Dia. 1 mm. to 200 mm. Description: Ring gauges have an outer steel casing, which protects the inner carbide ring. Usage: Ring gauges are used to check the outside diameter of work pieces. The work piece is inserted into the Inner dia. Of the steel ring. If it passes through the GO ring gauge then it means that the work piece is good for its lower size limit. If the work piece does not pass through the NOGO ring gauge it means that the work piece is OK for the higher size limit. A ring gauge is also effective to check out of roundness on the higher side. A master setting ring is used as a standard to set bore gauges, which can then be used to determine deviation from the master size.
Spare parts for gamesa
High speed 360 Rotating Electric PCB Pancake slip ring ultra thin 6mm pancace slipring 12 circuits Operating Speed 0-300 rpm Number of Circuits 2 24 Voltage 240 VAC/DC Current Rating 10A per circuit Temperature Range -20 Cto 80 C Contact Material Gold to Gold Lead Size 22 silver plated copper Lead Length Standard 250 mm(9.843inch) Dielectric Strength 500 VAC 50Hz, between each circuit Insulation Resistance 100 M 500 VDC Electrical Noise 5m Min Q1: Are you a We are a professional manufactory with High-level R & D team. Q2: How many types of the slip rings do you have A: We can supply all kinds of the slip rings.Such as minitary slip ring,customized sliring, miniature slip ring,fiber optical slip ring,RF rotary joint,HD combined-type, disc slip ring,wind power slip ring,solar power slip ring,through-bore slip ring, etc. Q3: Can you supply the slip rings with high frequency signals and(or) optical communication signals. A: Yes, we can supply mixed signals slip rings as your request.
FYH Anti-corona Ring Corona rings are annular metal rings that are fixed to the ends of bushings and insulator strings. They are also referred to as anti-corona rings. Corona rings are used to prevent corona discharges that occur in high voltage transmission lines. Corona Ring Corona rings are annular metal rings that are fixed to the ends of bushings and insulator strings. They are also referred to as anti-corona rings. Corona rings are used to prevent corona discharges that occur in high voltage transmission lines. Corona discharge or corona loss is a major problem in EHV transmission lines that cause power loss. One way to reduce corona discharge is to use corona rings. How do corona rings work? Corona discharge occurs when the electric field (potential gradient) on the surface of a conductor exceeds a critical value, called the critical destruction voltage. The value of the critical destruction voltage varies with atmospheric conditions. The value is about 30 kV/cm. The electric field is greatest where the curvature is sharpest. Therefore, corona discharges occur first at the points of greatest curvature - i.e., suspension points, corners and edges. Corona rings are installed at these points to prevent corona formation. Corona rings are electrically connected to conductors around points where corona discharges may occur. Thus, due to its smooth circular shape, the corona ring distributes the electric field (or charge) over a wider area. As a result, it reduces the potential gradient below the critical damage value. Manufacturers typically recommend installing aluminum corona rings at the conductor end of string insulators for lines above 230 kV and at both ends of insulators for 500 kV.
High speed 360 Rotating Electric PCB Pancake slip ring ultra thin 6mm pancace slipring 12 circuits Operating Speed 0-300 rpm Number of Circuits 2 ~ 24 Voltage 240 VAC/DC Current Rating 10A per circuit Temperature Range -20�°Cto +80�°C Contact Material Gold to Gold Lead Size 22# silver plated copper Lead Length Standard 250 mm(9.843inch) Dielectric Strength â?¥500 VAC @50Hz, between each circuit Insulation Resistance 100 M�© @ 500 VDC Electrical Noise 5m�©Min Q1: Are you a factory or a trading company? A: We are a professional manufactory with High-level R & D team. Q2: How many types of the slip rings do you have? A: We can supply all kinds of the slip rings.Such as minitary slip ring,customized sliring, miniature slip ring,fiber optical slip ring,RF rotary joint,HD combined-type, disc slip ring,wind power slip ring,solar power slip ring,through-bore slip ring, etc. Q3: Can you supply the slip rings with high frequency signals and(or) optical communication signals. A: Yes, we can supply mixed signals slip rings as your request.
Description: Ethernet slip rings can be used in any electromechanical system that requires unrestrained, continuous rotation while transferring power or data from a stationary to a rotating structure. The HE012 support 2 ~ 24 circiuts signal or power and 1 channel Profibus ethernet slip rings, with through bore size 12.7mm , overall diameter 56mm, flange mounting can optionel. It is standard, off-the-shelf, Color-coded lead wires are used on both the stator and rotor for simplified electrical connections. Ethernet slip ring can mixed with electrical power and signal channel USB slip ring can support 1-10 channels at the same time Slip ring Ethernet can support the RJ45 connector Military coating tenology , pricious metal and hard gold plating Super low BER error rate and high signal to noise ratio Benefits: Unique signal handling performance with minimal electrical circuit noise Very low electric noise Anti-jamming ,very low cost Very low contact resistance (Less than 1m�©) No maintenance and better reliability than traditional sling rings Suitable for signal and power transfer of rotating devices or instruments
