Exhaust heat boiler, waste heat boiler, fin tubes.
Heating pad.
Name: Flexible Graphite Sheet Description: Flexible graphite sheet is made with pure expanded graphite. Sungraf brand flexible graphite sheet has a high purity of 99% carbon content Advantages: better chemical resistance, better thermal conductivity, and better sealability. Usage:â? As gasket material, it is usually fabricated into Graphite Laminate, reinforced graphite sheet â?¡widely used in fluid sealing applications: flange gasket, spiral wound gasket, heat exchanger gasket, etc. â?¢It can also be used as solid lubricant in metal stamping and forming applications, or as heat liner in industry furnaces and other heating devices Standard Size TypeThick (mm)Width (mm)Length(mm) In Sheets0.2-6.01000, 15001000, 1500 In Rolls0.2-1.51000, 150030m-100m
Waste heat boiler with fin tubes & pin tubes Depend on the design as the customer's request
Fin tubes with different types depend on your design Wood case or steel frame
Product Model APV model T4 Q055E M107 R5 TR9GN B205 H12 Q055D M092 R8 TR9GL B158 H17 Q080E M060 R8GI SR6GL B134 N35 Q080D J060 R10 SR6AG B110 N25 A055 J092 R14 SR2(R2) B063 N50 A085 J107 TR9AL SR3 P190 Q030E A145 J185 TR9AV SR9 P105 Q030D K71 K55 K34
We are a China based plate heat exchanger manufacturer, and we specialize in plate type heat exchanger, all kinds of plates and gaskets producing. 500+ moulds are with us, and we can replace the most applied plates and gaskets for Alfa Laval Gea, APV, Tranter, Sondex, Funke, Thermowave etc. Thereâ??s no difference when comparing our products with genuine ones. And through the past 13 years, we have been selling them to all over the world, especially in European and American markets. The GEA brand, plates and gaskets we can produce and replace is: NT50T NT50M NT50X NT100TNT100M NT100X NT150L NT150S NT250S NT250M NT250L NT350S NT350M Our plate material 304, 316L, Titanium, Hastelloy C-276 254SMO 904L; Our gasket and ring gasket material NBR, EPDM, VITON, HNBR, CR;
Weâ??re a China based plate heat exchanger manufacturer, and we specialize in plate type heat exchanger, all kinds of plates and gaskets producing. 500+ moulds are with us, and we can replace the most applied plates and gaskets for Alfa Laval Gea, APV, Tranter, Sondex, Funke, Thermowave etc. Thereâ??s no difference when comparing our products with genuine ones. And through the past 13 years, we have been selling them to all over the world, especially in European and American markets. The GEA brand, plates and gaskets we can produce and replace is: VT04 VT10 VT20 VT205 VT20P VT40 VT40(M) VT405P VT405 VT80 VT80(M) VT805 VT2508 Our plate material 304, 316L, Titanium, Hastelloy C-276 254SMO 904L; Our gasket and ring gasket material NBR, EPDM, VITON, HNBR, CR;
Wide Runner (Free Flow) Plate Heat Exchanger Maximum treatment capacity: 5000 cubic meters/hour Maximum design pressure: 40 bar Maximum temperature resistance: 200â?? Minimum temperature differenceï¼?0.5-1â?? Tube diameter: DN15~500 Plate thickness: 0.4mm - 1.2mm Gasket material: NBR, EPDM, HNBR,HT-NBR,HEPDM,CR,VITON/FKM Plate material: 304, 316, 316L, titanium, titanium palladium, hastelloy C276, 254SMO, nickel, 904L, etc. Large mean logarithmic temperature difference 02 Large log-averaged temperature difference Plate heat exchanger is mostly parallel or counter-current flow mode. Select the number of processes and channels, the initial selection of cold, hot fluid flow and the number of channels, and thus calculated flow rates. Cold, hot fluid in the plate heat exchanger flow parallel to the heat transfer surface, no bypass, thus making the end temperature difference is small, the logarithmic mean temperature difference is large .
Plate And Shell Heat Exchanger Plate Pack ATW40 ATW50 ATW100 ATW150
The double wall plate heat exchanger plate is welded integrally with two thin plate pieces along the corner hole of each pair of plates. When the plate leaks, for example, the perforation caused by long time working will be easily detected from outside. Thereby it stops mixing between two materials.And at the same time, they plays very important roles towards warning internal leakage. Combined with the double seal of the gasket, the possibility of mixing two materials is avoided, and it is suitable for applications with high sanitary requirements or high safety and reliability of industrial production. Since the two sheets are welded to form a sheet, the heat transfer coefficient is inevitably lowered, but the highest safety is achieved in preventing materials mixing.
The semi welded plate heat exchanger is composed of a pair of plates, and each of the two plates is laser welded to form a pair of plates. It is sandwiched between the fixed pressing plate and the movable pressing plate in a superimposed manner Product introduction Semi welded plate heat exchanger The semi welded plate heat exchanger is composed of a pair of plates, and each of the two plates is laser welded to form a pair of plates. It is sandwiched between the fixed pressing plate and the movable pressing plate in a superimposed manner. The mesh contacts are formed between adjacentplates and supported by each other, and the rigidity of the plates is remarkably enhanced. Our semi welded plate heat exchanger adopts advanced laser welding technology, which has the advantages of small welding deformation, small residual stress and high quality.Qingdao Ruipute has advanced welding technology, especially for the first time to achieve the welding technology of special materials such as titanium, we are at the domestic leading level in developing and manufacturing semi-welded titanium plate heat exchange equipment. The cavity of the pair of plates forms a pass of a medium; the two pairs of plates are sealed by a sealing gasket which is resistant to corrosion, high temperature and high pressure, and constitutes another medium pass; the two mediums flow evenly in a countercurrent way in the adjacent channels to complete the sufficient heat exchange process. This structure ensures the stability of the welded plate pairs, providing easy maintenance of each pair of plates. It has the characteristics of high safety, high heat transfer efficiency, long service life and easy maintenance. It is suitable for cooling and chemical treatment. It is the ideal alternative equipment to shell and tube heat exchanger and all welded plate heat exchanger.Especially suitable for evaporation and condensation of ammonia coolants,as well as chemical treatment of corrosive liquids. Maximum volume:5000m3 /h; Maximum design pressure:25bar Maximum temperature:150 celsius degree; Minimum difference in temperature:0.5-1celsius degree Nozzle diameter:DN15~DN500; Plate thickness:0.5mm - 1.2mm Gasket material:NBR, EPDM, HNBR, HT-NBR, HEPDM,CR,VITON/FKM Fixed and movable plate material: Carbon Steel, Stainless Steel, and others on request. Plate material:AISI304, AISI316, AISI316L, Titanium,Ti-Pa,Hastelloy C276,254SMO, Nickel, AISI904L. Characteristics The semi welded heat exchanger has the general characteristics with shell and tube heat exchanger, and yet have other features like
Product introduction The plate condenser consists of plates that are welded together in pairs to form a so-called plate set. The concept of a plate set leads to two different types of channels: a weld channel for condensing steam and a gasket seal channel for cooling water. This type of plate is specially designed for optimum condensation. It has an asymmetrical arrangement with a large gap on the steam side and a small gap on the cooling water side. This makes it possible to maintain a very low pressure drop at the steam end while maintaining a certain speed and turbulence on the cooling water side. This maximizes heat transfer efficiency and minimizes fouling. Plate condensers are specially developed for condensing steam under low pressure or vacuum conditions in evaporation and distillation systems. It can meet a variety of specific applications and capabilities requirements. The steam inlet fitting is large and the two condensate outlets are small. The cooling water fitting is a medium size and is located in the center of the plate. Maximum heat transfer area: 500m2/set; Maximum design pressure:16bar Maximum temperature:200 celsius degree; Nozzle diameter:DN50~DN700 Plate thickness:0.5mm-1.2mm; Gasket material:NBR, EPDM, HNBR, HT-NBR, HEPDM, CR, VITON/FKM Fixed and movable plate material: Carbon Steel, Stainless Steel, and others on request. Plate material:AISI304, AISI316, AISI316L, Titanium, Ti-Pa,Hastelloy C276,254SMO,Nickel, AISI904L. Features Plate condenser Lower cost Due to the high heat transfer efficiency, this means less heat exchange area and higher cost efficiency than conventional shell and tube type, especially when stainless steel or titanium is required. The compact design also saves space, thus reducing transportation and installation costs. Plate condenser Less fouling Due to the high strength turbulence created by the specially designed corrugated sheets, there is less fouling on the cooling water side than the shell and tube condenser. Plate condenser Easy to clean The cooling water side is easy to clean, whether in the way of mechanical or chemical. Plate condenser Easy to expand Just add an extra "plate group" in the existing frame. Plate condenser Complete counterflow A greater degree of subcooling of non-condensable gases can be achieved compared to shell and tube equipment. Therefore, the load of the vacuum pump will be reduced. Range of application Alumina, food industry, sugar industry, beverage industry, industrial wastewater, etc.
Product principle The working principle of the plate evaporator is to compress the secondary steam generated by the equipment through the configured compressor, then raise the pressure and temperature to a certain range, and finally transfer it to the relevant heating chamber of evaporator as heating steam. Finally, to perform the condensation heat release program, so that it can help the latent heat of the steam and the recycling can be effectively obtained. Maximum heat transfer area: 500m2/set; Maximum design pressure:16bar Maximum temperature:200 celsius degree; Nozzle diameter:DN50~DN500 Plate thickness:0.4mm;Gasket material:NBR, EPDM, HNBR, HT-NBR, HEPDM, CR, VITON/FKM Fixed and movable plate material: Carbon Steel, Stainless Steel, and others on request. Plate material:AISI304, AISI316, AISI316L, Titanium, Ti-Pa,Hastelloy C276,254SMO,Nickel, AISI904L. Advantages Plate evaporator High heat transfer efficiency The plate evaporator is ingenious in design, so the heat transfer efficiency is higher than that of the general evaporator. Generally, the plate evaporator area only needs about one-half of the tube evaporator then can achieve the same evaporation effect. Plate evaporator Compact overall structure The whole structure is compact, floor space is small, and there is no need to invest too much manpower and material resources in the later use process. For some maintenance work, it only needs to be carried out in the original space range, and it's very simple whether it is disassembled or installed . Plate evaporator Diversification of components The heat exchange area can be effectively adjusted according to the customer's needs: now the heat exchange area of different evaporators has different ranges, since the heat exchanger plates can be disassembled, so multiple components with multiple skills and more new functions can be provided through adjusting number of plates and changing relative flow path. Plate evaporator Small heat loss Because this type of equipment is compact in structure and relatively light in weight, compared with tubular evaporators, it also reduces heat loss, and such equipment usually does not need to be insulated. Plate evaporator Less pressure loss Under the same heat transfer coefficient condition, such evaporator equipment can control the pressure loss within a certain range by rotating a reasonable flow rate.Compared with tubular evaporator,it can reduce 2/3 pressure loss. Plate evaporator Stable and safe operation Different sealing procedures are designed on the sealing device between the plates, and Range of application Metallurgy, food industry, paper industry, air conditioning, chemical and desalination industries
Principle A plate and frame heat exchanger as known as gasketed plate heat exchanger is a high efficiency heat exchanger that assembled from metal sheets with corrugated pattern and different kind of gaskets. Plate heat exchangers are the ideal equipment for heat exchange between liquid-liquid and liquid-vapor.In the case of the same pressure loss, the heat transfer coefficient is 3-5 times higher than that of the tube heat exchanger, but the floor space is one-third of the tube heat exchanger, and the heat recovery rate can be as high as 90% or more. Maximum volume: 5000m3 /h;Maximum design pressure: 25bar Maximum temperature: 200 celsius degree; Minimum difference in temperature: 0.5-1 celsius degree Nozzle diameter: DN15~DN500;Plate thickness: 0.4mm - 1.2mm Gasket material:NBR, EPDM, HNBR, HT-NBR, HEPDM, CR,VITON/FKM Fixed and movable plate material: Carbon Steel, Stainless Steel, and others on request. Plate material:AISI304, AISI316, AISI316L, Titanium,Ti-Pa,Hastelloy C276,254SMO,Nickel, AISI904L. Plate heat exchanger High heat transfer coefficient The design of the plate corrugation is aimed at the high thermal conductivity. The special flow path are formed by the plate corrugation causing strong disturbance flow at a very low flow rate, which is called turbulent flow. And the disturbance flow can be self-cleaning to prevent fouling and thus the heat transfer efficiency is high. Plate heat exchanger Large logarithmic temperature difference The temperature difference at the end is small, and the plate heat exchanger is mostly a cocurrent or countercurrent type of flow. In addition,there's no bypass flow. Plate heat exchanger Small footprint and easy maintenance The plate heat exchanger has a compact structure, and the heat exchange area per unit volume is 2-5 times that of the shell-and-tube type, and the floor area of the plate heat exchanger is about 1/2-1/3 of the shell - tube heat exchanger when achieving same heat exchange capacity .
Product principle The plate and shell heat exchanger adopts a circular corrugated heat exchanger plate that welded into a heat exchanger lathed bundle and combined with the structure of the pressure vessel shell. It also has a high heat transfer efficiency,compact structure and resistant to high temperature & pressure like shell tube heat exchanger. The plate and shell heat is durable under high temperature & pressure,large temperature difference and thermal shock, which is in a leading position in the industry. Maximum volume:2500m3/h; Maximum design pressure:100bar Maximum temperature:450 celsius degree; Minimum difference in temperature:0.5-1celsius degree Nozzle diameter:DN25~DN500; Plate thickness:0.8mm - 1.2mm Gasket material:NBR, EPDM, HNBR, HT-NBR, HEPDM,CR,VITON/FKM Fixed and movable plate material: Carbon Steel, Stainless Steel, and others on request. Plate material:AISI304, AISI316L, Titanium,Ti-Pa,Hastelloy C276,254SMO,Nickel, AISI904L. Features Plate Shell Heat Exchanger Safe and reliable Unique and durable lathed bundle structure: It can resist pressure shock and thermal shock very well; round plate and circular ring welding, stress distributes evenly; no welding between lathed bundle and shell, and it can withstand various thermal expansion (deformation ).The tubular shell structure is a strong, durable and safe pressure vessel; it can be installed in any position without being affected from outside; the solid protective shell will not leak or burst, and there is no danger of leakage to the environment.
Plates & Gaskets For Heat Exchanger 1.Raw material purchases from the same factory with famous brands like Alfa Laval, GEA, Funke etc. 2.Plates produced by precision molds and advanced press machine that detect & correct regularly. 3.Adpot same production and technology with Gislaved Gummi to ensure gasket quality. Plates material: SS304, SS316, SS316L, Titanium, Ti-Pd, Hastelloy-C276, Nickel, 254 SMO, 904L. Plates thickness: 0.5mm - 1.2mm Gaskets material: NBR, EPDM, HNBR, HT-NBR, HEPDM, VITON/FKM, FDA sanitary Hanging method: Glued, Hang on, Clip on, Snap in, Paraclip, Sonderlock. *Other materials may be available on request.
Plates & Gaskets For Heat Exchanger 1.Raw material purchases from the same factory with famous brands like Alfa Laval, GEA, Funke etc. 2.Plates produced by precision molds and advanced press machine that detect & correct regularly. 3.Adpot same production and technology with Gislaved Gummi to ensure gasket quality. Plates material: SS304, SS316, SS316L, Titanium, Ti-Pd, Hastelloy-C276, Nickel, 254 SMO, 904L. Plates thickness: 0.5mm - 1.2mm Gaskets material: NBR, EPDM, HNBR, HT-NBR, HEPDM, VITON/FKM, FDA sanitary Hanging method: Glued, Hang on, Clip on, Snap in, Paraclip, Sonderlock. *Other materials may be available on request.
Our static casting foundry and foundry expert have more than 30 years of production experience, we is focusing on the castings for heat treatment furnace components, our heat resistant casting for heat treatment fixtures are casted by investment casting , namely lost wax casting, and sand casting methods. Main products includes casting stackable baskets for heat treatment furnaces, trays and grids for furnace, roller hearth trays , serpentines trays , furnace fixtures, jigs, for chamber furnace, pit furnaces. Our company work with german companies for long term cooperation, most of our castings are exported to germany, france, italy, spain, usa, south america, turkey, sa and get very good reputation from our valued customer, more products like fan wheel, skid riders, link belt casting, loading bars, cross beams, walking beams. (cast furnace fans, grids, and baskets, high alloy heat resistant casting base tray and basket)
Our static casting foundry and foundry expert have more than 30 years of production experience, we is focusing on the castings for heat treatment furnace components, our heat resistant casting for heat treatment fixtures are casted by investment casting , namely lost wax casting, and sand casting methods. Main products includes casting stackable baskets for heat treatment furnaces, trays and grids for furnace, roller hearth trays , serpentines trays , furnace fixtures, jigs, for chamber furnace, pit furnaces. Our company work with german companies for long term cooperation, most of our castings are exported to germany, france, italy, spain, usa, south america, turkey, sa and get very good reputation from our valued customer, more products like fan wheel, skid riders, link belt casting, loading bars, cross beams, walking beams. (cast furnace fans, grids, and baskets, high alloy heat resistant casting base tray and basket)
