Hammer crusher is mainly applied to low abrasion materials with medium hardness and compression strength not exceed 100mpa. Such as coal, salt, chalk, gypsum, bricks & tiles, limestone, etc. It is also used to crush wood chips with strong fiber structure and tenacity, and the waste from asbestos cement to recycle asbestos fiber, etc. In addition, hammer crusher can be not only applied in crushing line and sand production line, but also is applied instead of cone crusher.
Jaw Crusher is mainly used to crush kinds of mining stones primarily and the largest compression resistance of the material to be crushed is 320Mpa. The jaw crusher is widely used in mining, metall-urgical industry, building material, highway, railway and chemical industry. Working Principle: The motor transmits power through belt, drives the moving jaw do periodic motion to the fixed jaw surround the eccentric shaft. The angle between toggle plate and moving jaw increases when moving jaw moves up. So the moving jaw closes to the fixed jaw. The stuff will be crushed in this process. The angle of Jaw Crusher between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw of Jaw Crusher moves away from fixed jaw by the pulling of rod and spring, the products after crushing will be discharged from the outlet of Jaw Crusher. Characteristics: High ratio of crushing, homogeneous final grain size, simple structure, reliable working condition, easy maintenance, low operating cost. Type Inlet size (mm) Max Feeding Size (mm) Discharge Size(mm) Power (KW) Capacity (T/H) PE150x250 150x250 125 10-40 5.5-7.5 1-5 PE200x350 200x350 125 15-40 7.5-11 5-16 PE250x400 250x400 210 20-60 15-18.5 5-20.
Ball mill is the key equipment for grinding after the crushing process.It is widly used in the processing of cement, silicate, new building material, refractory material, fertilizer, ferrous and nonferrous metal, glass as well as ceramics. It is used to grind dry or wet ores and other materials of grindability. Feeding size(mm)
The jaw crusher is drived by motor through belt and belt wheels, which makes the movable jaw plate up and down through eccentric shaft.When the movable jaw comes down, the angle between the fixed jaw plate and the movable jaw plate gets smaller, then the materials can be crushed .When the movable jaw plate rises, the angle becomes lauger and the movable jaw plate leaves the fixed jaw plate with the function of tie bar and spring.At the same time the final products are discharged from the lower outlet of the crushing chamber. Specification This series of products have the advantages of big reduction ratio, even granularity, simple structure, liable operation, easy maintenance, economic operation cost, etc. It is widely used for materials with the max crushing compressive strength not more than 320 mpa in the field of mine, metallurgy, building materials, roads, railways, irrigation, chemical industry, etc.
Features It has the characteristics of novel structure, no-bond connecting, high chrome plate hammer, special impact lining plate and energy saving.The finished product is in cubical shape and the discharge granularities can be adjusted.It simplifies the crushing process. Operating principle Impact crusher is a kind of crushing equipment which uses impact energy to crush maters.When getting into the effective area of hammer plates, due to the high speed of striking, the raw materials are thrown onto the impact equipment which is installed above the rotor.Then the materials are rebounded to the effective area of hammer plates and crushed again in the crushing chamber . At last, when the particles reach to the proper size, they will be discharged from the bottom of the machine. Pf impact crusher series The series of products can deal with the materials with max length below 500mm, and the compressive strength below 350mpa. They have the advantage of greater reduction ratio and the final materials are in cubical shape.
The low speed transmission is convenient for maintenance and starting.And the oil mist spray lubrication device ensures the reliable lubricating of big and small gears.Generally, the main motor of the large mill is high pressure asynchronous motor or synchronous motor.So customers should indicate the motor type in order.
Adopting advanced structure of the similar products in foreign countries, the high-rate raymond mill is designated on the basis of modification and renovation of large scale raymond mills. Compared with ball mills, the high-rate raymond mill has higher efficiency, lower power consumption, and smaller area occupying and smaller lump-sum investment. Due to the centrifugal force, the roller mills grind tightly on the rings. Thus it will not influence the output and granularity of the finished products even when the roller and the ring have wear-out in some degree. It is designated for processing superfine powder of over 300 noninflammable and nonexplosive materials with mohs hardness below grade 8 and water content below 6% in the field of mine , chemical industry, building materials, such as barite, calcite, potash feldspar, steatite, marble, limestone, dolomite, fluorite, lime, active carclazyte, active carbon, bentonite, kaolin, cement, phosphorus ore, gypsum, glass, manganese ore, titanium ore, copper mine, chrome ore, refractory materials, heat preservation materials, coal coke, coal fines, black, , bone meal, titanium white powder, , quartz, and so on. The finished products can be adjusted freely from 80 to 325 meshes with max meshes of 600 for some materials.
Application in glass cutting1.To cut the glass of household electrical appliances.2.To cut glass used in shower room.3.To cut glass for architectural decoration, craftwork and auto.It is the only fit way to use waterjet to cut anomalous shapes of glass. It solvesthe problems of making characters and hollowed-out work with glass. That is tosay, all difficulties is readily solved by waterjet cutting. For instance, to makelarge glass screen, glass curtain wall, all kinds of electrical appliance panelsand glass wares. Simple packing.
Application in processing tiles, stones and other building materials.Water cutter is applied in this field much earlier. Currently, the overwhelming majorityin this area use it. They focus on artistic matching. At present, tile matchingand stone matching have expanded all over the world. It is the best way to use water cutter to process tiles. It largely improved productionefficiency and processing precision. It achieved an epochal progress of tilesfurther processing, as it said good bye to the traditional ways of manual grindingand polishing. Presently waterjet cutting is mainly used to make all kindsof complex tile or marble matching . Simple packing.
1. Technical Parameter about UHP PUMP SYSTEM Parameter\Model 4000c Max pressure(Mpa/Psi ) 400/60,000 Working pressure(Mpa) 380 Orifice dia(mm) 0.33 Power(KW/HP) 37/50 L * W * H(M) 1.6*1.1*1.3 Cooling Air Max water flow 3.7L/MIN Shift way Electric shift.
The stone production line is composed of vibrating feeder, jaw crusher, impact crusher, vibrating sieve, belt conveyor and computer controlling board; its design output veries from 50 tons to 500tons per hour. In order to meet the needs of different clients, cone crusher and dust collecting equipment can be added to the prodution line. It can be used in industry like hydroelectricity, building materials, express way, city construction to operate the aggregate of hard limestone, granite, pebble, slag of metallurgy and man-made sand. We can combine different model of machines in the production line according to different technical process. Brief introduction of the stone production line Big block of stone is evenly conveyed to jaw crusher by vibrating feeder via silo for primary crushing. After primary crushing, the stone is sent to impact crusher by belt conveyor for secondary crushing. Then the stone is tronsported to vibrating sieve for screening, thus the stone can be classified into several groups depending on the size. The stone with a necessary size will be sent by belt conveyor to the palce where finished product is piled; otherwise, the stone will be conveyed by belt conveyor to the impact crusher for another crushing, thus a circular production process is formed. Introduction of stone production line performance This production line is highly automatic, except the turning on, turning off and daily maintenance of the equipments no other mannual operations are needed. It enjoys the advantages like: high efficiency, low cost, high throughput, high profit, evenly-sized and good-shaped finished product, meeting the national requirements of rapid need of raw materials.
Jaw crushers series made by henan zhengyi construction machinery co.;ltd has the top quality with competitive price. This series of jaw crusher is mainly used to break materials whose compression strength is less than 320mpa in secondary and coarse crushing. It has the features as follows: high crushing rate, high throughput, even discharged material size, simple structure, reliable performance, easy maintenance, low cost. It has been widely used in mining, metallurgy, building materials, highway, railway and irrigation works. Performance features of jaw crusher: This series of jaw crusher has the fatures of simple struture, reliable performance, easy maintenance. It is mainly used in ore dressing, building materials, road construction, silicate and chemical industry. The maximum compression strength this machine can sustain is 320mpa. Our crusher is mainly used to break all kinds of ore and big block materials in secondary crushing. It is widely used in mining, metallurgy, building materials, highway, railway, irrigation works and chemical industry. The maximum compression strength for the machine is 320mpa. Usage and scope of jaw crusher íí 1. This series of crusher is mainly used in metallurgy, mining, chemical, cement, construction, refractories and ceramics to crush ore and rock with a medium hardness in secondary and fine crushing.íííííííííííí 2. This series of crusher is suitable to crush soft minerals with a compression strength less than 300mpa, the maximum size of the materials should not be bigger than that in the technical data form.
It is mainly used in areas of coal dust, coal slurry, middlings, coke powder, coking coal or scrap powder in metallurgy, and refractories. Ball press machine is always needed when powdery materials need smelting. Working principle After being screened, only the powder with a size less than 3mm can be sent into the ball press machine. The size of the briquette will be 35mm*25mm*15mm. Under the requirement of client, we can produce press machine that can make spificic size of balls with a bulk density of 1.9-2.2g/cm3 and the hardness as that of a quick lime block. The finished products needs screening, only qualified ones can be stored and waits for being smelt.
This jaw crusher is ideal for primary and secondary crushing. With the increase of production, our jaw crusher can greatly reduce the operating costs. And it is of reliability and flexibility. The large feed opening and force-feeding action from the inward and downward eccentric movement of the swing jaw mean that our jaw crusher can increase the capacity. The jaw has a smaller discharge setting, allowing for a higher degree of flexibility with relative equipment. Positive setting adjustment is easy. The jaw crusher has features of simplicity, easy access and low maintenance.
The impact crusher is a new design that produces an excellent cubical product. This impact crusher produces a high ratio of reduction. The impact crusher is built for durability and simplicity of operation. Adjustment is easy from the exterior of the crusher. Maintenance is simple through inspection doors, and electric power unit is standard. The impact crushers offer greater reliability, high production and are ideal for portable mounting. It features of simple structure, zero key connection and special impact liner. When crushing hard rocks, it is of efficiency and energy conservation; the products are of cubic shape; the sizes of the discharging particles are adjusted; the crushing process can be simplified; the production cost can be cut down.It features of simple structure, zero key connection and special impact liner. When crushing hard rocks, it is of efficiency and energy conservation; the products are of cubic shape; the sizes of the discharging particles are adjusted; the crushing process can be simplified; the production cost can be cut down.
The whole line is highly automatic and the size of the finished products is even, good-shaped and can be adjustable. With high crushing ratio, low power consumption and high capacity, the plant is suitable for big, middle and small projects such as road and bridge construction. This stone production line has features of high automation, adjustable size of discharged granularity, high broken ratio, low energy consumption, large output, high uniform granularity and good shape of the products, and it is suitable for various engineering project constructions, such as highway, bridge and so on.
Shibo jaw crushers are ideal for primary and secondary crushing. With the increase of production, our jaw crusher can greatly reduce the operating costs. And it is of reliability and flexibility. The large feed opening and force-feeding action from the inward and downward eccentric movement of the swing jaw mean that our jaw crusher can increase the capacity. The jaw has a smaller discharge setting, allowing for a higher degree of flexibility with relative equipment. Positive setting adjustment is easy. The jaw crusher has features of simplicity, easy access and low maintenance. Working principle of jaw crusher: The motor transmits power through belt, drives the moving jaw to do periodic motion towards the fixed jaw by the eccentric shaft. The angle between toggle plate and moving jaw plate increases when moving jaw moves . So the moving jaw moves towards the fixed jaw. The stuff will be crushed in this process. The angle between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw moves leaves fixed jaw by pulling rod and spring, the final crushed stuff will be discharged from the outlet. Characteristics of jaw crusher: -high ratio of crushing, -even final size, -simple structure, -reliable working condition, -easy maintenance, -low operating cost.
Features and benefites In the micro-power grinding room, the rollers hanged on the roller lifting frame, which is fixed with the main sheft and the scraper knife.The pressure spring press on the outer of the cantilever by tension rod, with the corss arm sheft as the supporting point.Let roller tightly press on the inner surface of the ring.When the motor moved with equipment, the scraper knife on the scraper frame moved with the roller at the same time.As the roller moved on the inner sphere surface and moved itself.Analyzer let the analyzer runner rotated by motor equipments, and the power fineness depend on the speed adjustment of the analyzer. Applicability High pressure grinding mill is suitable in grinding bartle, limestone, ceromic, coking coaland so on.It is mainly applied to the power processing of mineral products in the industries of mining, metallurgy, constrution materials and chemicl materials.Ect.More than 280 kinds of high finesse power grinded, and the final product size can be adjusted as requied in the rang of 80-425meshes(even til 1000meshes). Export standard
MODEL Max. Feed Size (mm) Discharge Size (mm) Capacity (t/h) Motor power (KW) PE-600X900 520mm 65-130 50-150 75
A new product by absorbing advanced technologies from home and abroad. The impact crusher machine is ideal choice for crushing and screening. The most outstanding advantage of this machine is that its finished power is in good, cubic shape and without tensility and cranny. So the final products of the impact crusher machine is ideal used in highway and railway surface as well as water and electricity industry.
